Sharp MX-PEX1 (serv.man3) Service Manual ▷ View online
45
Fiery X3eTY2 system software
Installing system software over the network port
The System Software CDs contain the system software and the system software installer.
To install system software using the network port on the Fiery X3eTY2, you need:
To install system software using the network port on the Fiery X3eTY2, you need:
• A crossover Ethernet cable (4-pair/8-wire, short-length)
The MFP Ethernet cable is a crossover Ethernet cable, and may be used for system
software installation.
software installation.
• A Windows XP/2000 computer with:
• A CD-ROM drive, built in or attached
• Support for 100BaseTX or 1000BaseT
T
O
INSTALL
SYSTEM
SOFTWARE
OVER
THE
NETWORK
PORT
N
OTE
:
Before beginning system software installation, disable all Internet firewalls and
anti-virus software on the Windows XP/2000 computer.
1.
Power off the MFP using the secondary power switch on the Control Panel, and then the
main power switch inside the front compartment.
main power switch inside the front compartment.
2.
Move the power switch on the Fiery X3eTY2 to the Off (O) position (see Figure X on
page 47).
page 47).
3.
Remove all external cables from the Fiery X3eTY2, except for the power cable.
Leave the power cable connected to the Fiery X3eTY2.
46
Fiery X3eTY2 system software
4.
Connect the Ethernet crossover cable to the Fiery X3eTY2 network port and to a
Windows XP/2000 computer (see Figure W)
Windows XP/2000 computer (see Figure W)
N
OTE
:
The MFP Ethernet cable is an Ethernet crossover cable. To use the cable in this
step, disconnect the cable from the Fiery X3eTY2 and the MFP. For information about
how to identify a crossover cable, see Figure V on page 42.
how to identify a crossover cable, see Figure V on page 42.
F
IGURE
W
Creating an isolated Ethernet network using a crossover cable
5.
Power on the computer and insert System Software CD 1 into the computer CD-ROM drive.
6.
If the installer does not start automatically, navigate to the CD-ROM drive and
double-click the drive icon.
double-click the drive icon.
7.
At the Welcome screen, click Next.
8.
Read the Software License Agreement. Select “I Agree” to continue the installation
process, and then click Next.
process, and then click Next.
9.
At the Connection Type screen, make sure Ethernet is selected. Click Next to advance to
the Confirmation screen.
the Confirmation screen.
N
OTE
:
Ignore the text and graphics on this Confirmation screen. The graphics on this
screen may not accurately depict Fiery X3eTY2 hardware.
Network connector
Windows 2000/XP computer
Ethernet crossover cable
47
Fiery X3eTY2 system software
10.
Flip the Fiery X3eTY2 service switches to the service mode position (to the “ON”
position).
position).
See Figure X below.
F
IGURE
X
Fiery X3eTY2 power and service switches
After you install system software, return the service switches to the normal (OFF)
position (away from “ON”).
position (away from “ON”).
11.
Power on the Fiery X3eTY2 by moving its dedicated power switch to On (|) position.
Wait approximately 10 seconds for the Fiery X3eTY2 to start up and show “FF” on the
LED display.
LED display.
12.
Click Next on the computer screen.
13.
At the Installation screen, click Next to commence installation. Wait while the files
are copied and installed.
are copied and installed.
N
OTE
:
Progress is slow at first. For most computers, expect to wait approximately
20 minutes.
If prompted, select your network adapter and click OK.
If you click Cancel, you must power off the Fiery X3eTY2 using its dedicated power
switch, click Next on the computer screen (ignoring the text and graphics on this screen),
click Finish, and then repeat this procedure starting from step 6. If the installation
terminates abnormally, reboot the computer as well.
switch, click Next on the computer screen (ignoring the text and graphics on this screen),
click Finish, and then repeat this procedure starting from step 6. If the installation
terminates abnormally, reboot the computer as well.
Service switches
Flip the service switches
from normal (OFF) position...
from normal (OFF) position...
...to service mode (ON) position:
Power switch
LED display
48
Fiery X3eTY2 system software
14.
At the computer message “Please insert DISK 2,” remove System Software CD 1 from the
computer CD-ROM drive. Insert System Software CD 2, and click OK on the computer
screen.
computer CD-ROM drive. Insert System Software CD 2, and click OK on the computer
screen.
After all the system software files are copied to the Fiery X3eTY2, a computer screen
appears prompting you to restore the Fiery X3eTY2 connections and switches.
appears prompting you to restore the Fiery X3eTY2 connections and switches.
N
OTE
:
Ignore the text and graphics on this screen. The graphics on this screen may not
accurately depict Fiery X3eTY2 hardware.
15.
Power off the Fiery X3eTY2 using its dedicated power switch.
16.
Flip the service switches down to normal position (away from “ON”).
17.
Disconnect the crossover cable from the network port and the Windows XP/2000
computer.
computer.
18.
Reconnect all cables between the Fiery X3eTY2 and the MFP (see Figure T on page 38).
If you used the MFP Ethernet cable in this procedure, reattach the cable to the MFP and
to the MFP Ethernet port on the Fiery X3eTY2.
to the MFP Ethernet port on the Fiery X3eTY2.
19.
Click Next on the computer screen.
20.
Click Finish when the message is displayed that the installation is successful.
Remove System Software CD 2 from the computer.
Remove System Software CD 2 from the computer.
21.
Power on the MFP using the main power switch in the front compartment, and then the
secondary power switch on the Control Panel. Move the power switch on the Fiery X3eTY2
to the ON (|) position.
secondary power switch on the Control Panel. Move the power switch on the Fiery X3eTY2
to the ON (|) position.
Allow the MFP to start up and display Ready status on the control panel.
22.
When the “Initializing print controller. Please wait” message appears on the MFP touch
panel, press OK.
panel, press OK.
23.
Press the System Settings button on the MFP.
24.
On the touch panel, press Admin Password and then press Password.
25.
On the touch panel, use the keyboard to enter the administrator password for the MFP.
Press OK and then press OK again at the next screen.
Press OK and then press OK again at the next screen.
N
OTE
:
This password is not the same as the administrator password for the
Fiery X3eTY2.
26.
At the System Settings screen, use the arrows to scroll to Printer Settings and press
Printer Settings.
Printer Settings.
The Select Language screen appears.
27.
Use the arrows on the left to display the customer’s desired language, and press the
selection key on the right that corresponds to OK.
selection key on the right that corresponds to OK.
Click on the first or last page to see other MX-PEX1 (serv.man3) service manuals if exist.