Sharp MX-PE10 FIERY (serv.man2) Service Manual ▷ View online
R
EPLACING
PARTS
36
T
O
SHUT
DOWN
FROM
THE
MFP
TOUCH
PANEL
N
OTE
:
Notify the network administrator before you remove the Fiery Server from
the network.
1 Make sure that the Fiery Server is not receiving, processing, or printing any jobs.
If Printing appears on the touch panel, the Fiery Server is processing. You must wait until the
system finishes and reaches Idle before restarting or shutting down.
system finishes and reaches Idle before restarting or shutting down.
If the system has just finished processing, wait at least five seconds after the system reaches
Idle before beginning the shutdown procedure.
Idle before beginning the shutdown procedure.
Before accessing internal components, make sure that all cables are disconnected from the
back of the Fiery Server.
back of the Fiery Server.
2 Change the MFP touch panel display to the Fiery Server desktop, if needed.
3 Click the Start button > Shut down.
R
EPLACING
PARTS
37
Opening the Fiery Server
To service internal components, open the Fiery Server as described in the following
procedure.
procedure.
• Never lift the Fiery Server by grasping the top panel. The top panel does not support the
weight of the system.
A
VERTISSEMENT
:
Ne jamais soulever le serveur d'impression par sa partie supérieure : celle-ci ne peut pas supporter le
poids du système.
A
VVERTENZA
:
Il server di stampa non deve essere mai sollevato afferrandolo dal pannello superiore, in quanto
quest'ultimo non può sostenere il peso dell'intero sistema.
W
ARNUNG
:
Heben Sie den Druckserver nicht an der oberen Gehäuseabdeckung an. Die obere Gehäuseabdeckung ist
nicht dafür ausgelegt, das Gesamtgewicht des Systems zu tragen.
A
DVERTENCIA
:
No levante nunca el servidor de impresión agarrándolo por el panel superior. El panel superior no
soporta el peso del sistema.
A
VISO
:
Nunca erga o servidor de impressão pelo painel superior. O painel superior não suporta o peso do sistema.
W
AARSCHUWING
:
Til de afdrukserver nooit op door het bovenpaneel vast te nemen. Het bovenpaneel kan het gewicht
van het systeem niet dragen.
T
O
OPEN
THE
F
IERY
S
ERVER
1 Shut down the Fiery Server (see
page 34
).
2 Remove all cables from the back of the Fiery Server.
3 Remove the Fiery Server from the furniture (see
page 38
).
4 Remove all panels necessary to access the component that you need to service.
For guidelines on which panels to remove, see the service procedure for the component that
you want to access.
you want to access.
N
OTE
:
When removing multiple panels from the Fiery Server, use the following order:
• Left panel (see
page 38
)
• Right panel (see
page 38
)
• Front panel (see
page 39
)
• Top panel (see
page 40
)
N
OTE
:
When replacing panels, reverse the order.
5 Place the Fiery Server on a flat surface. Attach an ESD wrist strap before handling internal
parts (see
page 13
).
6 Carefully position the Fiery Server so that it is resting on its side and the internal
components are facing up.
Place removed components on a grounded, antistatic surface.
R
EPLACING
PARTS
38
T
O
REMOVE
AND
REPLACE
THE
LEFT
OR
RIGHT
PANEL
1 Remove the screws that secure the panel to the back of the chassis.
Set aside the screws so that you can replace them later.
2 Pull the back edge of the panel away from the chassis and lift the panel off the chassis.
F
IGURE
7:
Removing/replacing the side panels
3 To replace the panel, fit the front edge of the panel on the pivot post in the chassis.
4 Rotate the panel closed against the back of the chassis and replace the screws that you
removed earlier.
Make sure not to damage cables as you replace the panel. Fold all cables inside the chassis
before closing the panel against the chassis.
before closing the panel against the chassis.
Pivot post inside chassis
Left side panel
Right side panel
R
EPLACING
PARTS
39
T
O
REMOVE
AND
REPLACE
THE
FRONT
PANEL
N
OTE
:
To remove the front panel, you must first remove the left and right panels.
1 Remove the upper faceplate from the front of the chassis.
Press down to release the two tabs that secure the upper faceplate to the front panel, and then
carefully remove the upper faceplate from the front panel.
carefully remove the upper faceplate from the front panel.
N
OTE
:
You must remove the upper faceplate in order to remove the front panel from
the chassis.
2 Pull outward on the six tabs that secure the front panel to the chassis, and then lift the panel
off of the chassis.
First remove the two top tabs, then the two middle tabs, and then the two bottom tabs.
F
IGURE
8:
Removing/replacing the front panel
3 To replace the front panel, align the four cutouts in the panel with the power and reset
buttons and front USB ports.
4 Press the panel against the chassis to snap it into place.
Snap the tabs in pairs (first the top tabs, then the middle tabs, and then the bottom tabs).
5 Replace the upper faceplate.
Insert the two standoffs at the base of the faceplate into the chassis, and then carefully press
the faceplate against the chassis to lock the faceplate into place.
the faceplate against the chassis to lock the faceplate into place.
Upper faceplate
Click on the first or last page to see other MX-PE10 FIERY (serv.man2) service manuals if exist.