Sharp MX-PE10 FIERY (serv.man2) Service Manual ▷ View online
U
SING
THE
F
IERY
S
ERVER
28
T
O
SHUT
DOWN
,
RESTART
,
OR
REBOOT
FROM
THE
MFP
TOUCH
PANEL
N
OTE
:
Notify the network administrator before you remove the Fiery Server from
the network.
1 Make sure that the Fiery Server is not receiving, processing, or printing any jobs.
If Printing appears on the control panel, the Fiery Server is processing. You must wait until
the system finishes and reaches Idle before restarting or shutting down.
the system finishes and reaches Idle before restarting or shutting down.
If the system has just finished processing, wait at least five seconds after the system reaches
Idle before beginning the shutdown procedure.
Idle before beginning the shutdown procedure.
2 Change the MFP touch panel display to the Fiery Server desktop, if needed.
3 Click the Start button > Shut down.
Before accessing internal components, make sure that all cables are disconnected from the
back of the Fiery Server.
back of the Fiery Server.
R
EPLACING
PARTS
29
R
EPLACING
PARTS
Generally, the Fiery Server requires no regular service or maintenance. Use the procedures in
this chapter to inspect, remove, reseat, and replace major hardware components, as well as
install system software.
this chapter to inspect, remove, reseat, and replace major hardware components, as well as
install system software.
Overview
This chapter includes information about servicing the following components:
• Boards and cables
• Motherboard components (DIMMs, CPU, CMOS, jumpers, and battery)
• Fans
• Power supply
• Hard disk drive
• DVD drive
Replacement parts are available from your authorized service representative. The terms
“replace” and “replacing” are used throughout this document to refer to the reinstallation of
existing components. Install new components only when necessary. If you determine that a
component that you have removed is not faulty, reinstall it.
“replace” and “replacing” are used throughout this document to refer to the reinstallation of
existing components. Install new components only when necessary. If you determine that a
component that you have removed is not faulty, reinstall it.
N
OTE
:
Replacement parts and specifications are subject to change. Install the correct parts as
directed by your service/support center.
When performing the service procedures described in this chapter, follow the precautions
listed on
listed on
page 11
.
The tools required to service the Fiery Server are listed on
page 14
.
R
EPLACING
PARTS
30
Fiery Server overview diagrams
F
IGURE
3:
Front and connector panel
Front panel
Connector panel
USB ports
Power button
Control panel
DVD drive
Reset button
N
OTE
:
Use the
reset button
only if the
system is
unresponsive to
keyboard or
mouse actions.
only if the
system is
unresponsive to
keyboard or
mouse actions.
Eject button
Power connector
Network port (RJ-45)
Straight-through
Ethernet port (RJ-45)
Ethernet port (RJ-45)
USB ports (x2)
DVI port
USB ports (x2)
VGA port
Power switch
|: Power On
O: Power Off
|: Power On
O: Power Off
Printer interface port
R
EPLACING
PARTS
31
F
IGURE
4:
Connector panel and internal side view
Key
1 Power connector
2 Network port
3 DVI port (for connecting to the monitor on the MFP)
4 VGA port
5 Straight-through Ethernet port
6 USB ports (x2)
7 USB ports (x2)
8 Printer interface board
9 CPU cooling assembly
10 Power supply
11 DIMM slots
12 DVD drive
13 Removable drive (option)
14 Hard disk drive in bracket
15 Motherboard
16 Front fan
N
OTE
:
Cables, UIB, and front panel USB ports are not shown.
1
2
3
5
6
9
7
15
16
14
13
12
8
11
4
10
8
Click on the first or last page to see other MX-PE10 FIERY (serv.man2) service manuals if exist.