Sharp MX-M950 / MX-MM1100 (serv.man37) Service Manual ▷ View online
MX-M1100 ADJUSTMENTS 6 – 69
13-B
Monochrome image send mode, image
density and gradation adjustment
(by each mode)
density and gradation adjustment
(by each mode)
Normally, there is no need to perform this adjustment. In the follow-
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When there is a defective copy in a scan image.
* When the scan image density is too light.
1)
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When there is a defective copy in a scan image.
* When the scan image density is too light.
1)
Enter the Sim. 46-5 mode.
2)
Select a mode to be adjusted with the scroll button.
3)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
4)
Scan a monochrome document in the color scan mode (Scan
to PC or Scan to e-Mail), and check the density of the received
image.
Check can be made also in the copy mode by the following
procedure.
4) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
to PC or Scan to e-Mail), and check the density of the received
image.
Check can be made also in the copy mode by the following
procedure.
4) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
13-C
Image send mode, image color balance
adjustment
adjustment
Normally, there is no need to perform this adjustment. In the follow-
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When the scan image color balance is defective.
1)
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When the scan image color balance is defective.
1)
Enter the Sim. 46-8 mode.
2)
Select a color to be adjusted with [R], [G], [B] buttons.
3)
Select a mode (low density section or high density section) to
be adjusted with the scroll button.
be adjusted with the scroll button.
4)
Enter the adjustment value with 10-key, and press [OK] key.
To increase the density of the target color, increase the adjust-
ment value. To decrease the density of the target color,
decrease the adjustment value.
To increase the density of the target color, increase the adjust-
ment value. To decrease the density of the target color,
decrease the adjustment value.
5)
Scan a color document in the color scan mode (Scan to PC or
Scan to e-Mail), and check the density of the received image.
Check can be made also in the copy mode by the following
procedure. The scanned image, however, is in monochrome.
5) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
Scan to e-Mail), and check the density of the received image.
Check can be made also in the copy mode by the following
procedure. The scanned image, however, is in monochrome.
5) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
Display/Item
Content
Setting
range
Default
A
AUTO TEXT
Auto/Text mode
1 - 99
50
B
AUTO TEXT/PRINT
PHOTO
PHOTO
Auto/Text/Printed
Photo mode
Photo mode
1 - 99
50
C
AUTO TEXT/
PHOTO
PHOTO
Auto/Text/Photograph
mode
mode
1 - 99
50
D
TEXT
Text mode
1 - 99
50
E
TEXT/PRINTED
PHOTO
PHOTO
Text/Printed Photo
mode
mode
1 - 99
50
F
TEXT/PHOTO
Text/Photograph mode
1 - 99
50
G
PRINTED PHOTO
Printed Photo mode
1 - 99
50
H
PHOTOGRAPH
Photograph mode
1 - 99
50
I
MAP
Map mode
1 - 99
50
OK
A㧦 50
㧧
AUTO TEXT
B㧦 50
㧧
AUTO TEXT/PRINT PHOTO
C㧦 50
㧧
AUTO TEXT/PHOTO
D㧦 50
㧧
TEXT
0
A:
SIMULATION NO.46㧙05
EXPOSURE ADJUSTMENT(B/W)[SCANNER]
50
㨇
1 㨪 99 㨉
TEST
CLOSE
E㧦 50
㧧
TEXT/PRINTED PHOTO
F㧦 50
㧧
TEXT/PHOTO
G㧦 50
㧧
PRINTED PHOTO
H㧦 50
㧧
PHOTOGRAPH
I㧦 50
㧧
MAP
Display/Item
Content
Setting
range
Default
A
LOW DENSITY
POINT
POINT
Low density section
color balance
adjustment value
color balance
adjustment value
1 - 99
50
B
HIGH DENSITY
POINT
POINT
High density section
color balance
adjustment value
color balance
adjustment value
1 - 99
50
A㧦 50
㧧
LOW DENSITY POINT
B㧦 50
㧧
HIGH DENSITY POINT
0
A:
SIMULATION NO.46㧙08
SCANNER COLOR BALANCE ADJUSTMENT 㧔COLOR SCANNER MODE㧕
50
㨇
1 㨪 99 㨉
B
G
R
OK
TEST
CLOSE
MX-M1100 ADJUSTMENTS 6 – 70
13-D
FAX send mode, image sharpness
adjustment
adjustment
Normally, there is no need to perform this adjustment. In the follow-
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When the sharpness in the FAX send mode is too low.
Note:
Normally this adjustment value may be set to the default and there
is no need to perform the adjustment. When, however, the sharp-
ness of a printed image on the receiving FAX side to too low, per-
form this adjustment.
When performing this adjustment, be sure to check that the receiv-
ing side FAX is normal.
1)
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When the sharpness in the FAX send mode is too low.
Note:
Normally this adjustment value may be set to the default and there
is no need to perform the adjustment. When, however, the sharp-
ness of a printed image on the receiving FAX side to too low, per-
form this adjustment.
When performing this adjustment, be sure to check that the receiv-
ing side FAX is normal.
1)
Enter the Sim. 46-39 mode.
2)
Select a mode to be adjusted with the scroll button.
3)
Enter the adjustment value with 10-key, and press [OK] button.
To increase the sharpness, increase the adjustment value. To
decrease the sharpness, decrease the adjustment value.
To increase the sharpness, increase the adjustment value. To
decrease the sharpness, decrease the adjustment value.
4)
Send a FAX message.
5)
Check the sharpness of the received FAX image.
Repeat the above procedures until a satisfactory result is
obtained.
Repeat the above procedures until a satisfactory result is
obtained.
ADJ 14
FAX send mode image quality
adjustment
adjustment
Normally this adjustment is not required. However, perform this
adjustment in the following cases:
* When the user request for performing this adjustment.
* When the FAX send image density is low or high.
NOTE:
Normally, the adjustment value may be set to the default value and
there is no need to make this adjustment. When, however, the
image density on the receiving FAX side is unsatisfactory, perform
this adjustment.
Before execution of this adjustment, however, be sure to confirm
that the receiving FAX operates normally.
adjustment in the following cases:
* When the user request for performing this adjustment.
* When the FAX send image density is low or high.
NOTE:
Normally, the adjustment value may be set to the default value and
there is no need to make this adjustment. When, however, the
image density on the receiving FAX side is unsatisfactory, perform
this adjustment.
Before execution of this adjustment, however, be sure to confirm
that the receiving FAX operates normally.
14-A
Image density and gradation adjustment in
the FAX send mode (Collective adjustment
of all the FAX modes)
the FAX send mode (Collective adjustment
of all the FAX modes)
1)
Enter the Sim. 46-40 mode.
2)
Press [EXECUTE] button.
The adjustment pattern is printed.
The adjustment pattern is printed.
3)
Check the print density in the adjustment pattern.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
4)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 2 thru 4 until a satisfactory result is
obtained.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 2 thru 4 until a satisfactory result is
obtained.
Display/Item
Content
Setting
range
Default
A
200
✕ 100 [DPI] OFF 200 ✕ 100 [DPI]
Half-tone OFF mode
0 - 2
1
B
200
✕ 200 [DPI] OFF 200 ✕ 200 [DPI]
Half-tone OFF mode
0 - 2
1
C
200
✕ 200 [DPI] ON
200
✕ 200 [DPI]
Half-tone ON mode
0 - 2
1
D
200
✕ 400 [DPI] OFF 200 ✕ 400 [DPI]
Half-tone OFF mode
0 - 2
1
E
200
✕ 400 [DPI] ON
200
✕ 400 [DPI]
Half-tone ON mode
0 - 2
1
F
400
✕ 400 [DPI] OFF 400 ✕ 400 [DPI]
Half-tone OFF mode
0 - 2
1
G
400
✕ 400 [DPI] ON
400
✕ 400 [DPI]
Half-tone ON mode
0 - 2
1
H
600
✕ 600 [DPI] OFF 600 ✕ 600 [DPI]
Half-tone OFF mode
0 - 2
1
I
600
✕ 600 [DPI] ON
600
✕ 600 [DPI]
Half-tone ON mode
0 - 2
1
A㧦 1
㧧
200100㨇DPI㨉 OFF
B㧦 1
㧧
200200㨇DPI㨉 OFF
C㧦 1
㧧
200200㨇DPI㨉 ON
D㧦 1
㧧
200400㨇DPI㨉 OFF
0
A:
SIMULATION NO.46㧙39
IMAGE SEND SHARPNESS ADJUSTMENT
1
㨇
0 㨪 2 㨉
OK
TEST
CLOSE
E㧦 1
㧧
200400㨇DPI㨉 ON
F㧦 1
㧧
400400㨇DPI㨉 OFF
G㧦 1
㧧
400400㨇DPI㨉 ON
H㧦 1
㧧
600600㨇DPI㨉 OFF
I㧦 1
㧧
600600㨇DPI㨉 ON
A㧦 50
㧧
EXPOSURE LEVEL(ALL)
0
A:
SIMULATION NO.46-40
EXPOSURE ADJUSTMENT(FAX㧦ALL)
50
㨇
1㨪 99 㨉
OK
TEST
CLOSE
EXECUTE
MX-M1100 ADJUSTMENTS 6 – 71
14-B
Image density and gradation adjustment in
the FAX send mode (Normal mode)
the FAX send mode (Normal mode)
1)
Enter the Sim. 46-41 mode.
2)
Select a mode to be adjusted with the scroll button.
3)
Press [EXECUTE] button.
The adjustment pattern is printed.
The adjustment pattern is printed.
4)
Check the print density of the adjustment pattern.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
5)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 3 thru 5 until a satisfactory result is
obtained.
To select the exposure mode actually used in the FAX send
mode, select item G and enter the set value corresponding to
the exposure mode with 10-key and press [EXECUTE] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 3 thru 5 until a satisfactory result is
obtained.
To select the exposure mode actually used in the FAX send
mode, select item G and enter the set value corresponding to
the exposure mode with 10-key and press [EXECUTE] button.
14-C
Image density and gradation adjustment in
the FAX send mode (Fine mode)
the FAX send mode (Fine mode)
1)
Enter the Sim. 46-42 mode.
2)
Select a mode to be adjusted with the scroll button.
Display/Item
Content
Setting
range
Default
A AUTO
FAX auto exposure mode
send image density
(Normal mode)
send image density
(Normal mode)
1 - 99
50
B EXPOSURE1
FAX exposure level 1 send
image density
(Normal mode)
image density
(Normal mode)
1 - 99
50
C EXPOSURE2
FAX exposure level 2 send
image density
(Normal mode)
image density
(Normal mode)
1 - 99
50
D EXPOSURE3
FAX exposure level 3 send
image density
(Normal mode)
image density
(Normal mode)
1 - 99
50
E EXPOSURE4
FAX exposure level 4 send
image density
(Normal mode)
image density
(Normal mode)
1 - 99
50
F EXPOSURE5
FAX exposure level 5 send
image density
(Normal mode)
image density
(Normal mode)
1 - 99
50
G EXECUTE
MODE
AUTO
1
1
(AUTO)
EXP1
2
EXP2
3
EXP3
4
EXP4
5
EXP5
6
A㧦 50
㧧
AUTO
B㧦 50
㧧
EXPOSURE1
C㧦 50
㧧
EXPOSURE2
D㧦 50
㧧
EXPOSURE3
0
A:
SIMULATION NO.46-41
EXPOSURE ADJUSTMENT(FAX㧦NORMAL)
50
㨇
1㨪 99 㨉
OK
TEST
CLOSE
E㧦 50
㧧
EXPOSURE4
F㧦 50
㧧
EXPOSURE5
G㧦 1
㧧
EXECUTE MODE㧦AUTO
EXECUTE
Display/Item
Content
Setting
range
Default
A AUTO
FAX auto exposure mode
send image density
(Fine mode)
send image density
(Fine mode)
1 - 99
50
B EXPOSURE1
FAX exposure level 1 send
image density (Fine mode)
image density (Fine mode)
1 - 99
50
C EXPOSURE2
FAX exposure level 2 send
image density (Fine mode)
image density (Fine mode)
1 - 99
50
D EXPOSURE3
FAX exposure level 3 send
image density (Fine mode)
image density (Fine mode)
1 - 99
50
E EXPOSURE4
FAX exposure level 4 send
image density (Fine mode)
image density (Fine mode)
1 - 99
50
F
EXPOSURE5
FAX exposure level 5 send
image density (Fine mode)
image density (Fine mode)
1 - 99
50
G AUTO
H_TONE
FAX auto exposure mode
send image density
(Half-tone/Fine mode)
send image density
(Half-tone/Fine mode)
1 - 99
50
H EXPOSURE1
H_TONE
FAX exposure level 1 send
image density
(Half-tone/Fine mode)
image density
(Half-tone/Fine mode)
1 - 99
50
I
EXPOSURE2
H_TONE
H_TONE
FAX exposure level 2 send
image density
(Half-tone/Fine mode)
image density
(Half-tone/Fine mode)
1 - 99
50
J
EXPOSURE3
H_TONE
H_TONE
FAX exposure level 3 send
image density
(Half-tone/Fine mode)
image density
(Half-tone/Fine mode)
1 - 99
50
K EXPOSURE4
H_TONE
FAX exposure level 4 send
image density
(Half-tone/Fine mode)
image density
(Half-tone/Fine mode)
1 - 99
50
L
EXPOSURE5
H_TONE
H_TONE
FAX exposure level 5 send
image density
(Half-tone/Fine mode)
image density
(Half-tone/Fine mode)
1 - 99
50
M EXECUTE
MODE
AUTO
1
1
(AUTO)
EXP1
2
EXP2
3
EXP3
4
EXP4
5
EXP5
6
AUTO H_TONE
7
EXP1 H_TONE
8
EXP2 H_TONE
9
EXP3 H_TONE
10
EXP4 H_TONE
11
EXP5 H_TONE
12
A㧦 50
㧧
AUTO
B㧦 50
㧧
EXPOSURE1
C㧦50
㧧
EXPOSURE2
D㧦50
㧧
EXPOSURE3
0
A:
SIMULATION NO.46-42
EXPOSURE ADJUSTMENT(FAX㧦FINE)
50
㨇
1 㨪 99㨉
OK
TEST
CLOSE
E㧦50
㧧
EXPOSURE4
F㧦50
㧧
EXPOSURE5
G㧦50
㧧
AUTO H_TONE
H㧦50
㧧
EXPOSURE1 H_TONE
I㧦50
㧧
EXPOSURE2 H_TONE
J㧦50
㧧
EXPOSURE3 H_TONE
K㧦50
㧧
EXPOSURE4 H_TONE
L㧦50
㧧
EXPOSURE5 H_TONE
EXECUTE
MX-M1100 ADJUSTMENTS 6 – 72
3)
Press [EXECUTE] button.
The adjustment pattern is printed.
The adjustment pattern is printed.
4)
Check the print density of the adjustment pattern.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
5)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 3 thru 5 until a satisfactory result is
obtained.
To select the exposure mode actually used in the FAX send
mode, select item M and enter the set value corresponding to
the exposure mode with 10-key and press [EXECUTE] button
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 3 thru 5 until a satisfactory result is
obtained.
To select the exposure mode actually used in the FAX send
mode, select item M and enter the set value corresponding to
the exposure mode with 10-key and press [EXECUTE] button
14-D
Image density and gradation adjustment in
the FAX send mode (Super fine mode)
the FAX send mode (Super fine mode)
1)
Enter the Sim. 46-43 mode.
2)
Select a mode to be adjusted with the scroll button.
3)
Press [EXECUTE] button.
The adjustment pattern is printed.
The adjustment pattern is printed.
4)
Check the print density of the adjustment pattern.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
If the print density of the adjustment pattern is unsatisfactory,
perform the following procedure.
5)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 3 thru 5 until a satisfactory result is
obtained.
To select the exposure mode actually used in the FAX send
mode, select item M and enter the set value corresponding to
the exposure mode with 10-key and press [EXECUTE] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
Repeat the procedures 3 thru 5 until a satisfactory result is
obtained.
To select the exposure mode actually used in the FAX send
mode, select item M and enter the set value corresponding to
the exposure mode with 10-key and press [EXECUTE] button.
14-E
Image density and gradation adjustment in
the FAX send mode (Ultra fine mode)
the FAX send mode (Ultra fine mode)
1)
Enter the Sim. 46-44 mode.
Display/Item
Content
Setting
range
Default
A AUTO
FAX auto mode send image
density (Super fine mode)
density (Super fine mode)
1 - 99
50
B EXPOSURE1
FAX exposure level 1 send
image density
(Super fine mode)
image density
(Super fine mode)
1 - 99
50
C EXPOSURE2
FAX exposure level 2 send
image density
(Super fine mode)
image density
(Super fine mode)
1 - 99
50
D EXPOSURE3
FAX exposure level 3 send
image density
(Super fine mode)
image density
(Super fine mode)
1 - 99
50
E EXPOSURE4
FAX exposure level 4 send
image density
(Super fine mode)
image density
(Super fine mode)
1 - 99
50
F EXPOSURE5
FAX exposure level 5 send
image density
(Super fine mode)
image density
(Super fine mode)
1 - 99
50
G AUTO
H_TONE
FAX auto exposure mode
send image density
(Half-tone/Super fine mode)
send image density
(Half-tone/Super fine mode)
1 - 99
50
H EXPOSURE1
H_TONE
FAX exposure level 1 send
image density
(Half-tone/Super fine mode)
image density
(Half-tone/Super fine mode)
1 - 99
50
I
EXPOSURE2
H_TONE
H_TONE
FAX exposure level 2 send
image density
(Half-tone/Super fine mode)
image density
(Half-tone/Super fine mode)
1 - 99
50
J
EXPOSURE3
H_TONE
H_TONE
FAX exposure level 3 send
image density
(Half-tone/Super fine mode)
image density
(Half-tone/Super fine mode)
1 - 99
50
A㧦 50
㧧
AUTO
B㧦 50
㧧
EXPOSURE1
C㧦50
㧧
EXPOSURE2
D㧦50
㧧
EXPOSURE3
0
A:
SIMULATION NO.46-43
EXPOSURE ADJUSTMENT(FAX㧦SUPER FINE)
50
㨇
1 㨪 99㨉
OK
TEST
CLOSE
E㧦50
㧧
EXPOSURE4
F㧦50
㧧
EXPOSURE5
G㧦50
㧧
AUTO H_TONE
H㧦50
㧧
EXPOSURE1 H_TONE
I㧦50
㧧
EXPOSURE2 H_TONE
J㧦50
㧧
EXPOSURE3 H_TONE
K㧦50
㧧
EXPOSURE4 H_TONE
L㧦50
㧧
EXPOSURE5 H_TONE
EXECUTE
K EXPOSURE4
H_TONE
FAX exposure level 4 send
image density
(Half-tone/Super fine mode)
image density
(Half-tone/Super fine mode)
1 - 99
50
L
EXPOSURE5
H_TONE
H_TONE
FAX exposure level 5 send
image density
(Half-tone/Super fine mode)
image density
(Half-tone/Super fine mode)
1 - 99
50
M EXECUTE
MODE
AUTO
1
1
(AUTO)
EXP1
2
EXP2
3
EXP3
4
EXP4
5
EXP5
6
AUTO H_TONE
7
EXP1 H_TONE
8
EXP2 H_TONE
9
EXP3 H_TONE
10
EXP4 H_TONE
11
EXP5 H_TONE
12
Display/Item
Content
Setting
range
Default
A㧦 50
㧧
AUTO
B㧦 50
㧧
EXPOSURE1
C㧦50
㧧
EXPOSURE2
D㧦50
㧧
EXPOSURE3
0
A:
SIMULATION NO.46-44
EXPOSURE ADJUSTMENT(FAX㧦ULTRA FINE)
50
㨇
1 㨪 99㨉
OK
TEST
CLOSE
E㧦50
㧧
EXPOSURE4
F㧦50
㧧
EXPOSURE5
G㧦50
㧧
AUTO H_TONE
H㧦50
㧧
EXPOSURE1 H_TONE
I㧦50
㧧
EXPOSURE2 H_TONE
J㧦50
㧧
EXPOSURE3 H_TONE
K㧦50
㧧
EXPOSURE4 H_TONE
L㧦50
㧧
EXPOSURE5 H_TONE
EXECUTE
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man37) service manuals if exist.