DOWNLOAD Sharp MX-M364N / MX-565N (serv.man5) Service Manual ↓ Size: 45.47 MB | Pages: 127 in PDF or view online for FREE

MX-M565N  MX-EB12N  25 – 2

Put a mark on both the mirroring kit HDD and the machine HDD
with a marker pen to indicate what is the mirroring HDD or the
machine HDD.

2) Disconnect the connector of the standard HDD and remove the

reuse band as the figure below. 

3) Attach the Mirroring unit to the standard HDD, and install the

unit to the main unit and fix it with the screws (Packed item
No.2). Attach the cable clamp which was removed at the proce-
dure 1).

4)

Connect the cable to the mirroring unit.

5) Arrange the RAID harness and connect the it to MFP control

PWB as the figure below.

ĭ

ĭ

Ĭ

Į

MX-M565N  MX-EB12N  25 – 3

1) Attach the shield plate.

2) Attach the left cabinet.

1) Turn on the main power switch and the operation panel power

switch.
Date copying from the standard HDD to the mirroring unit HDD
is started. It is called “Rebuilding.”

2) Check to confirm that the machine is booted. 

It takes about two hours to complete rebuilding. Do not turn off
the power during rebuilding. When, however, the power is
turned off during rebuilding, turn on the power again, and
rebuilding will be continued. During rebuilding, a message is
displayed to indicate the operation. A job can be performed
during rebuilding, though the job speed may be reduced.

1) Check to confirm that the mirroring kit active icon is displayed.
2) Use SIM62-20 to check to confirm that the HDD status is OK/

REBUILDING.

3) Perform copying and check to confirm that machine is normally

operating.

Be deleting the HDD mirroring information is necessary when dis-
continue use the mirroring kit.

RIB Buster software
The software is composed of the following two files. (They can be
downloaded from Tech DS Web site or Sharppcservice.com.)
-  RIB Buster{YYYYMMDD}.exe
-  Setup.ini

1)

-  USB cable
-  SATA connection cable
-  SATA connector
-  AC adapter
  (Support OS: Windows XP, Windows VISTA, Windows 7 (32/64bit)
  Windows PC

1)

Connect the target HDD to delete mirroring information with
the USB cable, SATA connection cable, SATA connector and
the AC adaptor as follows.

NOTE: When disconnect the cable from the HDD, be sure to dis-

connect the USB cable from the PC in advance.
If this precaution is ignored, the HDD may be damaged.

Mirroring kit installed

Mirroring kit/HDD trouble

Mirroring kit/Rebuilding

MX-M565N  MX-EB12N  25 – 4

2) Copy the RIB Buster software files (RIB Buster {YYYYM-

MDD}.exe and Setup.ini) to a same directory of the PC.
-  RIB Buster{YYYYMMDD}.exe
-  Setup.ini

3) Connect the target HDD to PC with USB cable.

4) Double-click RIB Buster {YYYYMMDD}.exe to boot the RIB

Buster software.
If the user account control is ON in VISTA or Windows7 set-
ting, the user account control menu is displayed. Click [Allow]
on this menu.

5) Select the target HDD to delete the mirroring information.

6)

Click [Clear RIB in HDD] button.

7)

Click [OK] button. (The mirroring information is deleted.)

8)

After completion of deleting the mirroring information, “OK” is
displayed.

Phenomenon 1
An error indicating an abnormality in the Setup.ini file when booting
the RIB Buster software.

Cause

Setup.ini file does not exists, or there is any 
abnormality in the file.

Countermeasures

Check to confirm that there is Setup.ini file in the 
proper directory and that there is no abnormality in 
the descriptions.

MX-M565N  MX-EB12N  25 – 5

Phenomenon 2
The mirroring information has not been deleted normally.

Phenomenon 3
Though the target HDD is connected, it is not displayed.

Cause

Temporary communication trouble, cable or other 
device trouble, HDD trouble

Countermeasures

1. Click [Clear RIB in HDD] button again.
2. If the trouble is not solved by procedure 1. , 
disconnect and connect the cable, change the 
devices, and reboot the RIB Buster. Then execute 
procedure 1.

Cause

The target HDD is not registered in the Setup.ini file. 
Cable or other device trouble, HDD trouble

Countermeasures

1. Reboot RIB Buster. Click the framed section.
2. If the trouble is not solved by procedure 1. , 
replace the Setup. ini file and the RIB Buster 
{YYYYMMDD} with the latest version, and execute 
procedure 1. .
3. If the trouble is not solved by procedure 2. , 
disconnect and connect the connector, change the 
devices, and reboot the RIB Buster. Then execute 
procedure 1. .