Sharp MX-M364N / MX-565N (serv.man5) Service Manual ▷ View online
MX-M565N AR-SU1 22 – 1
MX-M565N
Service Manual
[22] AR-SU1
1. Unpacking
A. Packed items check
*1: When replacing the stamp cartridge, Refer to “Stamp cartridge
replacement” in the “Operation Guide” (PDF document). The user
must be notified of that. (Do not refer to “Stamp cartridge replace-
ment procedure” (package part).)
replacement” in the “Operation Guide” (PDF document). The user
must be notified of that. (Do not refer to “Stamp cartridge replace-
ment procedure” (package part).)
2. Installation for RSPF
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. RSPF unit removal
1) Remove the screws, the RSPF relay cable unit, earth cable
and Disconnect the connector.
2)
Remove the RSPF unit from the main unit.
3)
Put the RSPF unit on a stable table with the OC mat upside.
B. Stamp unit attachment
1)
Open the OC mat.
2)
Remove the sensor cover.
No.
Name
Quantity
1
Stamp unit
1
2
Stamp cartridge replacement procedure
*1
1
3
Stamp cartridge
3
4
Installing screw
1
1
2
3
4
1
1
2
3
1
1
2
MX-M565N AR-SU1 22 – 2
3) Remove the screw from the stamp unit mounting section. Use
the removed screw to attach the stamp unit together with the
earth wire, and connect the connector.
earth wire, and connect the connector.
4) Install the sensor cover.
5) Close the OC mat.
C. RSPF unit attachment
1)
Attach the RSPF unit to the main unit.
2)
Connect the connector and fix the earth cable as the figure
below..
below..
- The cable of red circle needs to be arranged upward of the
hook.
hook.
- Fix the earth cable between the following red allow range.
3)
Attach the RSPF relay cable unit and fix it with screws which
were removed at the procedure A-1) with pressing the RSPF
relay cable unit at the red allow.
were removed at the procedure A-1) with pressing the RSPF
relay cable unit at the red allow.
1
2
2
4
5
4
3
1
3
3
2
2
2
1
MX-M565N AR-SU1 22 – 3
D. Finish stamp cartridge attachment
1) Open the left cover, and open the document tray.
2) Attach the finish stamp cartridge.
E. Turn ON the power of the main unit
1) Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
power switch.
F. Installation check
1) Use SIM22-10 to check to confirm that the finish stamp (AR-
SU1) is recognized.
3. Installation for DSPF
A. Install the stamp unit
1)
Open the DSPF unit, remove the OC mat.
2)
Remove the screw, and remove the paper exit PG cover.
Remove the screw.
Disengage the pawl, and remove the stamp case unit.
Remove the screw.
Disengage the pawl, and remove the stamp case unit.
3)
Remove the screw which fixs the earth cable and attach the
stamp unit (Packed items) to the stamp case which was
removed from the DSPF unit with the screw. (Fix it together
with the earth wire.)
stamp unit (Packed items) to the stamp case which was
removed from the DSPF unit with the screw. (Fix it together
with the earth wire.)
* Arrange the harness of the stamp unit as shown below.
1
2
2
4
3
MX-M565N AR-SU1 22 – 4
4) Install the stamp case unit, and fasten it with the screw. Install
the earth wire. Connect the connector.
5) Install the paper exit PG cover.
6) Disengage the pawl, and open the stamp case unit.
Install the stamp cartridge (Packed items).
7)
Install the OC mat to the SPF glass, and close the DSPF unit.
B. Turn on the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
2
4
1
3
2
1
3
Click on the first or last page to see other MX-M364N / MX-565N (serv.man5) service manuals if exist.