DOWNLOAD Sharp MX-M310 / MX-M310N (serv.man5) Service Manual ↓ Size: 6.6 MB | Pages: 39 in PDF or view online for FREE

MX-M260/M310/M260N/M310N MX-DS11/DS12 (Machine stand) 4 - 1

Unpack the package, and check to confirm that all the parts are pro-
vided.

Packed parts

1) Attach the casters to the desk.

Remove the desk from the package, and put it on the floor as
shown below. 
Attach the four casters and fix them with caster fixing screws. 
(3 screws for each caster)

2) Attach the adjusters. 

Attach the front adjusters (2 pcs.) and the rear adjusters (2 pcs.) as
shown in the figure below. 

Machine stand

Packed parts add

MX-DS11

MX-DS12

Casters: 4pcs.

Front adjusters: 2 pcs.

Rear adjusters: 2 pcs.

Adjuster covers: 2 pcs.

Caster fixing screws: 12 pcs.

Copier connecting fixtures: 
2 pcs.

Screws (S tight): 
2 pcs.

Screws (P tight): 
4 pcs.

(   110)

(   80)

Rear side

Casters

Casters

Front side

Caster fixing screws 
(3 for each caster)

Rear adjusters(   80)

Front 
adjuster

Front 
adjuster

Rear side

Front side

Screw the adjusters into 
the hole so that the adjuster 
tips do not extend out from 
the hole. 

∗

(   110)

(   110)

MX-M260/M310/M260N/M310N MX-DS11/DS12 (Machine stand) 4 - 2

3) Attach the adjuster covers. 

Put the desk on the floor in the normal state, and open the door.
(MX-DS11 only)
Slide the adjuster covers (2 pcs.) as shown in the figure below and
attach them. Then, close the door.

4) Remove the paper tray.

Pull out the paper feed unit tray from the copier until it stops.
Lift it and remove it from the copier. 

5) Put the copier (or the paper feed unit) on the desk.

Insert the positioning pins (2 pcs.) of the desk into the positioning
holes of the copier (or the paper feed unit). 
At that time, be careful not to break the fixtures on the desk side.

6) Connect the copier with the desk.

Connect the copier with the desk with two screws (P tight, packed
together with the copier) and the fixture.

7) Remove the two screws, and remove the rear cover.

8) Connect the copier (or the paper feed unit) and the desk with two

screws (P tight) and two screws (S tight) packed together with the
copier. When connecting, be careful of the direction of the connect-
ing fixture of the copier.

Front side

Adjuster covers

Adjuster covers

Front side

MX-DS11

MX-DS12

Positioning pin

Positioning pin

Be careful not to hit.

Machine stand

Copier

Fixture

Screws (P tight)

Front side

Screws (P tight)

Back side

Copier 
connecting
fixture

Screws (P tight)

Screws (P tight)

Screws (S tight)

Copier 
connecting
fixture

Screws (S tight)

MX-M260/M310/M260N/M310N MX-DS11/DS12 (Machine stand) 4 - 3

9) Attach the rear cover, and fix it with the two screws.

10) Install the paper tray.

Install the paper tray to the original position.

MX-M260/M310/M260N/M310N MX-FN13 (Finisher) 5 - 1

1) Unpacking

∗ When removing the finisher, put your hand beneath the unit and lift it

up as shown below. 

Check to confirm that all the packed parts are provided. 

2) Remove the paper exit tray cover as shown in the figure below. 

3) Open the front cover.

4) Remove the five screws, and remove the left cabinet. 

5) Remove the screws (3 positions) which are fixing the paper exit

tray.

FIN connection unit

FIN front cover

Second paper exit unit

Paper holding arm

Rail dummy cover

M3 x 8 S tight bind

(4 pcs.)

M3 x 10 S tight bind

(4 pcs.)

Resin grip

Harness clamp (2 pcs.)

(with M3 screw)

Staple position label