Sharp MX-M182 / MX-M182D (serv.man4) Service Manual ▷ View online
MX-M232D (MX-FX13/XB17) 6 - 7
11) Remove dummy panel.
<1>Unscrew from the dummy panel.
<2>Disengage the pawls, and remove the dummy panel from the
<1>Unscrew from the dummy panel.
<2>Disengage the pawls, and remove the dummy panel from the
machine.
12) Attach FAX keyboard.
<1>Connect the machine flat cable to FAX keyboard.
<2>Place the FAX keyboard onto the machine while engaging the
<1>Connect the machine flat cable to FAX keyboard.
<2>Place the FAX keyboard onto the machine while engaging the
pawls.
<3>Secure the keyboard using 2 screws.
13) Reattach keyboard back cover.
<1>Insert the claw lock of the keyboard back cover into the machine.
<1>Insert the claw lock of the keyboard back cover into the machine.
Make sure that the claw lock is securely inserted.
<2>Secure the cover using two screws.
14) Paste label on the rear cabinet of the machine.
After installing FAX Expansion Kit, paste the supplied label on the
position shown in the illustration.
position shown in the illustration.
15) Insert the power plug of the machine to the outlet, and then turn on
the main switch of the machine.
Destination setting <Europe only>
1) Enter the SIM66-2 mode.
2) Select the destinationing up/down key.
3) Press [OK] twice to set.
Setup date and time.
Press [FUNCTION] key on the Operation Panel, select [Key
Operator Program], enter 5-digit key operator code, and select
[FAX] mode.
Operator Program], enter 5-digit key operator code, and select
[FAX] mode.
Select [Initial setup] and then [Date and Time]. Enter date in the
order of year, Month, Day and press [OK] to set.
order of year, Month, Day and press [OK] to set.
Select [Time Setup], enter time in the order of Hour and Minute, and
press [OK] to set.
press [OK] to set.
16) Connect line cable.
Connect the line cable to the FAX Expansion Kit.
Connect the line cable to the FAX Expansion Kit.
USA, Canada only
In order to manifest the compliance with FCC Part 68 and IC CS-03, it
is required to provide the machine with the FCC Registration Number
(USA), Ringer Equivalence (USA) and Ringer Eqivalence (Canada).
After installing the FAX expansion kit in the machine, please put the
registration label, packed with the kit, on the prescribed location.
In order to manifest the compliance with FCC Part 68 and IC CS-03, it
is required to provide the machine with the FCC Registration Number
(USA), Ringer Equivalence (USA) and Ringer Eqivalence (Canada).
After installing the FAX expansion kit in the machine, please put the
registration label, packed with the kit, on the prescribed location.
Australia, New Zealand only
A-TICK label attachment.
A-TICK label attachment.
<Taiwan/Brazil/South Africa only>
Even when connecting the telephone line to TEL line, attach the core
to the telephone line.
Pass the line cable through the core twice.
Even when connecting the telephone line to TEL line, attach the core
to the telephone line.
Pass the line cable through the core twice.
Taiwan/Brazil/South Africa only
MX-M232D (MX-NB12) 7 - 1
[7] MX-NB12
1. Unpacking
2. Installation
1) Remove the screw. Remove the rear cabinet and the rear cabinet
cover.
2) Connect the bundled AC harness to the power PWB of the
machine.
Note: Connect the connector with the insulation tube of the AC harness
to the power PWB of the machine.
<Taiwan/Brazil/South Africa only>
No.
Name
Quantity
1
Network PWB mounting unit
1
2
Network PWB mounting unit
(Taiwan/Brazil/South Africa only)
(Taiwan/Brazil/South Africa only)
1
3
AC harness
1
4
AC harness (Taiwan/Brazil/South Africa only)
1
5
Rear cabinet cover
1
6
Screw
4
7
CD-ROM
2
1
3
5
6
7
2
4
(1)
(1)
(1)
(2)
(1)
(1)
(1)
(1)
(1)
(3)
(4)
MX-M232D (MX-NB12) 7 - 2
3) Remove one screw, and remove the USB device connector PWB
on the machine side.
4) Install the network PWB mounting unit and fix it with 4 screws.
Then connect the connector.
Connect the AC harness mounted to the main unit. Attach the reuse
snap band to the plate.
snap band to the plate.
<Taiwan/Brazil/South Africa only>
5) Attach the rear cabinet and the rear cabinet cover. Fix it with
screws.
Note: Since the power PWB is at the vicinity of the MX-NB12, use
enough care when repairing it.
(3)
(2)
(1)
(1)
(2)
(2)
(2)
(3)
(3)
(4)
(3)
(2)
(1)
(2)
(2)
(2)
(3)
(3)
(4)
(3)
(2)
(4)
(4)
(4)
(1)
(4)
(4)
(4)
(4)
(4)
(2)
(3)
MX-M232D (MX-TR10) 8 - 1
[8] MX-TR10
1. Unpacking
<Before installation>
• For improvement of workability, some description in this manual as
well as components and accessories may change without prior
notice.In this case, refer to the service manual.
notice.In this case, refer to the service manual.
2. Installation
2-1. Remove the right cabinet and the right front cab-
inet.
1) Open the document cover or the document feeder.
2) Open the bypass tray.
3) Remove the right door.
4) Open the front cover
5) Remove the five screws and then remove the right cabinet.
6) Remove the screw and then remove the right front cabinet.
2-2. Attach the separator motor unit.
1) Connect the connector.
2) Insert the two bosses of the machine into the positioning holes of
the separator motor unit and secure it with the supplied screw.
2-3. Arrange the wiring of the separator motor unit.
1) Insert the excessive cord into the clamp attached on the separator
motor unit and arrange the wiring as shown in the illustration.
2-4. Move the separator lever.
1) Rotate the separator gear to move the lever to the position shown in
the illustration. Do not move the lever position until operation check
is performed.
is performed.
Turn off the main switch of the machine and then remove the power
plug of the machine from the outlet.
plug of the machine from the outlet.
Click on the first or last page to see other MX-M182 / MX-M182D (serv.man4) service manuals if exist.