DOWNLOAD Sharp MX-FXX1 (serv.man2) Service Manual ↓ Size: 4.79 MB | Pages: 80 in PDF or view online for FREE

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 16

 

66-30

: Operation test/Check

Function (Purpose) : Used to display the TEL/LIU status change,

The display is highlighted by status change.

: FAX

: Operation

1)

When the machine enters Simulation 66-30, the following
screen is displayed.

2)

HS1, HS2, RHS, and EXHS are highlighted when the signal is
detected, and displayed normally when the signal is not
detected.

 

66-31

: Setting

Function (Purpose) : Used to set ON/OFF the port for output to

TEL/LIU.

: FAX

: Operation

1)

When the machine enters Simulation 66-31, the following
screen is displayed.
* When starting execution of the simulation, the current set-

ting is displayed.

2)

Change the port setting.
When a port is set to ON, the port display is highlighted. Two or
more ports can be selected.
* At that time, the actual port output is not reflected.

3)

When [EXECUTE] button is pressed, the changed setting is
reflected to the port which outputs to TEL/LIU.

4)

To terminate the process, press [EXECUTE] button again.
[EXECUTE] button returns to the normal display.

 

66-32

: Operation test/Check

Function (Purpose) : Used to check the fixed data received from

the line and to display the result.

: FAX

: Operation

1)

Press [EXECUTE] button to check the fixed data received from
the line. At that time, [EXECUTE] button is highlighted.
* Fixed data check procedure
• The data received from the line is checked of the following

fixed data status for minutes, then if they are in accord with
“OK” is displayed on LCD, if not “NG” is displayed.

• The judgment is made in 2 minutes.

Receive speed: 300BPS
Receive data: 00H
Judgment data: 100byte

2)

After completion of check, [EXECUTE] button returns to the
normal display. The result is displayed as "OK" or "NG."
* To check the fixed data again, press [EXECUTE] button, and

check of the fixed data can be made again.

 

66-33

: Operation test/Check

Function (Purpose) : Used to execute detection of various sig-

nals with the line connected and to display
the detection result. When a signal is
detected, the display is highlighted.

: FAX

: Operation

1)

When the machine enters Simulation 66-33, the following
screen is displayed.

2)

When a signal is detected, "FNET" and"BUSY TONE CNG
CED DTMF"are highlighted. When a signal is not detected,
they are normally displayed.

HS1

Polarity inversion signal

HS2

Polarity inversion signal

RHS

Handset hook SW

EXHS

External telephone hook SW

CION

MR

EC

S.

CLOSE

EXHS

HS2

HS1

SIMULATION

 NO.66-30

TEST

TEL/LIU

 SENSOR CHECK

RHS

FNET

BUSY TONE

CNG

CED

DTMF

EXECUTE

CLOSE

SIMULATION

 NO.66-31

TEST

TEL/LIU

 SETTING.

EC

CION

MR

S.

EXECUTE

CLOSE

SIMULATION

 NO.66-32

TEST

RECEIVED DATA CHECK

CHECKING

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 17

 

66-34

: Operation test/Check

Function (Purpose) : Used to execute the send test and display

the time required for sending image data in
the test. Used to execute send test and dis-
play. (Unit: ms)

: FAX

: Operation

1)

When the machine enters Simulation 66-34, the following
screen is displayed.

2)

When image data are actually sent, the time required for send-
ing the image data is displayed on the LCD.

* #### : Time

 

66-36

: Operation test/Check

Function (Purpose) : Used to check send and receive data from

the MODEM controller to the MFP control-
ler or the data line or the command line
individually.

: FAX

: Operation

1)

When the machine enters Simulation 66-36, the following
screen is displayed. (Default: left upper selected)

2)

Operation check
Select an item to be checked on the screen.
* When an item to be checked is selected, it is highlighted.

3.1. When "Operation check once" is selected:
● When (once) is selected:
When [EXECUTE] button is pressed under this state, [EXECUTE]
button is highlighted and the operation check is started.
After completion of the operation check, [EXECUTE] button returns
to the normal display and the check result is displayed.
When the check is normally completed, "OK" is displayed. In case
of an error, [NG" is displayed.
3.2. When "Operation check repeat" is selected:
● When [repeat] is selected:
When [EXECUTE] button is pressed under this state, [EXECUTE]
button is highlighted and the operation check is started.
* In the case of [Repeat] check, the title display is changed as fol-

lows for every execution of check.
"MFP-MDMC I/F CHECK.- *"

"MFP-MDMC I/F CHECK.- **"
"MFP-MDMC I/F CHECK.- ***"
"MFP-MDMC I/F CHECK.- ****"
"MFP-MDMC I/F CHECK.- *****"
Check is repeated until [EXECUTE] button is pressed or "NG"
occurs.
To stop the operation check, press [EXECUTE] button, and
[EXEUTE] button returns to the normal display and the operation
check is terminated.
* When an abnormality occurs during check, "NG" is displayed

and the operation is terminated.

 

66-39

: Setting

Function (Purpose) : Used to check and change the destination

setting saved in EEPROM of the FAX BOX.

: FAX

: Specifications

1)

When the machine enters the simulation, the currently set des-
tination button is highlighted. (In the default state, JAPAN is set
as the destination.)

2)

Select a destination button to set the destination. (In this
example, USA/CANADA is selected.) The selected button is
highlighted and the previously selected button returns to the
normal display.
* When the destination button is changed, the new destination

setting is saved to EEPROM of the FAX BOX.

* When, however, there is no destination setting in EERPOM

of the FAX BOX, "NO DESTINATION" is displayed on the
title line and all the destination buttons are normally dis-
played.

CLOSE

FNET

SIMULATION NO.66-33

TEST

SIGNAL DETECT CHECK.

BT/CNG/CED/DTMF

MFP 

← MDMC (DATA once)

MFP 

→ MDMC (DATA once)

Data line Once

Data line Once

MFP 

← MDMC (DATA repeat)

MFP 

→ MDMC (DATA repeat)

Data line Repeat

Data line Repeat

MFP 

← MDMC (CMD once)

MFP 

→ MDMC (CMD once)

Command line Once

Command line Once

MFP 

← MDMC (CMD repeat)

MFP 

→ MDMC (CMD repeat)

Command line Repeat

Command line Repeat

JAPAN

U.S.A/CANADA

EUROPE

AUSTRALIA

CHINA

ASIA&OTHERS

SIMULATION NO.66

36

TEST

MFP-MDMC I/F CHECK.

MFP<-MDMC (DATA once)

MFP->MDMC (DATA once)

MFP<-MDMC(DATA repeat)

MFP->MDMC(DATA repeat)

MFP<-MDMC (CMD once)

MFP>MDMC (CMD once)

EXECUTE

MFP<-MDMC (CMD repeat)

MFP->MDMC (CMD repeat)

CLOSE

CLOSE

AUSTRALIA

U.S,A/CANADA

JAPAN

SIMULATION NO.66-39

TEST

FAX DESTINATION SETUP

EUROPE

CHINA

ASIA&OTHERS

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 18

 

66-42

: Setting

Function (Purpose) : Used to rewrite the program to power con-

trol installed in the FAX BOX.

: —

: —

1)

Press [EXECUTE] button.[EXECUTE] button is highlighted
and YES] and [NO] buttons become active.

2)

Press [YES] button.
The power control program is rewritten.
* During rewriting the power control program, [EXECUTE] and

[YES] buttons are highlighted.

* When [NO] button or [EXECUTE] button is pressed, [EXE-

CUTE] button returns to the normal display, and [YES] and
[NO] buttons gray out.

3)

When rewriting of the power control program is normally com-
pleted, "OK" is displayed and [EXECUTE] button returns to the
normal display, and [YES] and [NO] buttons gray out.
* When rewriting of the power control program is failed, the

error message of "NG"is displayed and [EXECUTE] button
returns to the normal display, and [YES] and [NO] buttons
gray out.

 

66-43

: Setting

Function (Purpose) : Used to write the adjustment value into the

power control installed in the FAX BOX.

: FAX

: Setting

1)

When the machine enters Simulation 66-43, the following
screen is displayed. (Default: left upper selected)
* Use  [

↑] [↓] buttons to select the select item of the power

control adjustment value. Selection is made in Item A to H.
When the selected item is the top (last) item,  [

↑] [↓] buttons

gray out. (The highlighted section of the set value is
switched and the new value is displayed on the setting
area.)
When [

↑] [↓] buttons gray out, they are disabled.

* Enter the power control adjustment value with 10-key and

press [OK] button ([

↑] [↓] buttons). The set power control

adjustment value is saved to the primary memory area.

* The set data are saved in the primary memory area. There-

fore, the setting is reflected only when [EXECUTE] button is
pressed to execute.

* For the range of the power control adjustment value and

each value, refer to the table.

2)

When [EXECUTE] key is pressed, it is highlighted and writing
to the power control is executed. When writing is normally
completed, "OK" is displayed. When it is failed, "NG" is dis-
played.

3)

After completion of writing, [EXECUTE] key returns to the nor-
mal display.

SIMULATION NO.66-42

TEST

POWER CONTROL PROGRAM RELOAD

CLOSE

EXECUTE

ARE

YOU

SURE?

YES

NO

A

CI_LEVEL_JUDGE

2 to 15

2

B

CI_CYCLE_MIN

1 to 254

10

C

CI_CYCLE_MAX

2 to 255

110

D

CI_COUNT

2 to 15

3

E

POFF_LEVEL_JUDGE

2 to 15

15

F

EXHS_LEVEL_JUDGE

2 to 15

10

G

RHS_LEVEL_JUDGE

2 to 15

2

H

SON_TIMEOUT

1 to 127

20

CLOSE

A:

A :

2

B:

10

C : 110

D :

3

CI_LEVEL_JUDGE

CI_CYCLE_MIN

CI_CYCLE_MAX

CI_COUNT

SIMULATION NO.66-43

PIC ADJUSTMENT VALUE WRITING.

2

㨇 2㨪 15 㨉

OK

TEST

EXECUTE

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 19

1

1-8

M Country code

Control is performed according to the set country code.
The destination setting that is set in SIM66-2 as the image send 
function is reflected.
The country code setting cannot be directly made from this SW.

1

North America
* For codes of the 

other countries, 
refer to the page of 
SIM 66-2 setting.

0
1
1
0
1
0
1

2

1

Change from the 
image send screen to 
the copy screen

Setting to determine whether or not to automatically change from the 
image send screen to the copy screen.
When changing over, if no keys are operated for 20 seconds after 
pushing the final key in the image send mode, the copy mode will be 
automatically switched to.
If there is no changeover, the machine will remain in the image send 
mode and not switch to the copy mode.
"1": Change over
"0": Do not change over

1

Change over 
(North America)

Operation 
settings

0

Do not change over 
(Other country)

2-5

Image quality priority 
selection (standard 
image quality setting)

Setting to determine the initial setting for image quality selection when 
reading documents on the FAX.
"0000": Ordinary lettering
"0001": Small lettering
"0010": Fine
"0011": Very fine
"0101": Small lettering, medium tone
"0110": Fine, medium tone
"0111": Very fine, medium tone
"Ordinary lettering" (initial value) is reverted to if a value outside of the 
setting range is set.

0

Ordinary lettering

Operation 
settings

0
0
0

6

Image quality setting 
when saving (FAX)

Setting to determine whether or not to make filed image quality valid 
(initial setting for image quality selection when transmitting filed 
document files by FAX)
"1": Apply
"0": Do not apply

0

Do not apply.

Operation 
settings

7

Defaulted stamp 
setting

When using the document feeder (RSPF), this setting determines 
whether or not to use the finish stamp upon completion of the document 
reading.
 "1": Yes (use the finish stamp)
 "0": No (do not use the finish stamp)

0

No

Operation 
settings

8

Not used

0

3

1

Received data printing 
hold (FAX/Internet 
FAX) 

Setting to determine whether or not to store data received by FAX/
Internet FAX in the memory without outputting it.
"0": Do not hold
"1": Hold

0

Do not hold

Operation 
settings

2-3

M Tone/Pulse initial 

setting (Dial call signal 
setting)

This is set according to dial type.
"00": 10PPS (pulse)
"01": 20PPS
"10": TONE
"11": TONE
If "20pps" is set, adopt the initial TONE.

1

TONE

FAX initial 
setting

0

4

Auto startup mode

In the case where FAX or Internet FAX is received during nighttime 
mode or simulated mode, if this setting is ON, the received document 
will be outputted when the machine becomes able to output. When 
OFF, the machine will receive the data by proxy without outputting the 
document, but it will output the received document when the panel 
power SW is ON.
"0": Setting (setting for automatically starting up the main unit and 
outputting)
"1": Release (setting for storing in the memory without starting up the 
main unit)

0

Setting

FAX initial 
setting

5-8

M Pause time setting 

(between dials)

This sets the time per pause inputted during dialling.
The pause time can be set from 1 to 15 seconds in 1-second 
increments by binary inputting N over the range of 0 to 15 (1 second x 
N). 
If a value outside the setting range (or "0000") is set, the initial value of 
2 seconds is reverted to.

0

2 seconds

FAX initial 
setting

0
1
0