DOWNLOAD Sharp MX-FXX1 (serv.man2) Service Manual ↓ Size: 4.79 MB | Pages: 80 in PDF or view online for FREE

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 20

4

1-2

M Speaker volume when 

on-hook (Speaker 
volume during DTMF 
sending) 

This sets speaker volume for when the on-hook button is pushed.
Volume is available in three types.
"00": Medium
"01": Small
"10": Medium
"11": Large
If a setting outside the setting range is set, the initial value of Medium is 
reverted to.

1

Medium

FAX initial 
setting

0

3-4

M Call sound volume

Irrespective of whether there is a handset, this sets the volume of the 
call sound that is sounded when a signal arrives.
Volume is available in four types as follows.
"00": No sound
"01": Small
"10": Medium
"11": Large

1

Medium

FAX initial 
setting

0

5-6

M Line monitor volume 

setting

Set the speaker volume during line monitoring.
Volume is available in four types as follows.
"00": No sound
"01": Small
"10": Medium
"11": Large

1

Medium (North 
America/Australia/
Sweden/Finland/
Norway/Denmark/
Netherlands/Italy/
Switcherland/Austria/
New Zealand/China/
Singapore/Indonesia/
Thailand/Malaysia/
India/Philippine/Hong 
Kong/Taiwan/Middle 
East/Other3/Rusia)

FAX initial 
setting

0

0

No sound (U.K./
France/Germany/
Slovakia/South Africa/
Spain/Portuguese/
Luxemburg/Belgium/
Czech/Hungary/
Greece/Poland)

0

7-8

M Volume of the 

transmission 
completion sound
(Volume of the 
successful 
transmission sound)

Set the volume of the completion sound outputted from the speaker 
upon completion of FAX transmission.
Volume is available in four types as follows.
"00": No sound
"01": Small
"10": Medium
"11": Large

1

Medium

FAX initial 
setting

0

5

1-2

M Volume of the 

communication error 
completion sound. 
(Volume of the 
transmission and 
reception error sound)

This sets the volume of the completion sound outputted from the 
speaker upon completion of FAX communication error.
Volume is available in four types as follows.
"00": No sound
"01": Small
"10": Medium
"11": Large

1

Medium

FAX initial 
setting

0

3-4

M Volume of the 

reception completion 
sound (Volume of the 
reception completion 
sound)

This sets the volume of the completion sound outputted from the 
speaker upon completion of FAX reception.
Volume is available in four types as follows.
"00": No sound
"01": Small
"10": Medium
"11": Large

1

Medium

FAX initial 
setting

0

5-6

M Tone of the successful 

transmission sound

This sets the tone sounded when transmission is successful.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)

1

Pattern 3 (1000Hz)

FAX initial 
setting

0

7-8

M Tone of the 

transmission error 
sound

This sets the tone sounded when there is a transmission error.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)

1

Pattern 3 (1000Hz)

FAX initial 
setting

0

6

1-2

M Tone of the reception 

sound

This sets the tone sounded upon completion of reception.
"00": Pattern 1 (550Hz)
"01": Pattern 2 (750Hz)
"10": Pattern 3 (1000Hz)
"11": Pattern 4 (1700Hz)

1

Pattern 3 (1000Hz)

FAX initial 
setting

0

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 21

6

3-5

M Setting of the 

successful 
transmission sound 
time

This sets the time the tone is sounded when transmission is successful.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the setting range is 
set.

0

3.0 seconds

FAX initial 
setting

1
0

6-8

M Setting of the reception 

sound time

This sets the time the tone is sounded upon completion of reception.
"000": 2.0 seconds
"001": 2.5 seconds
"010": 3.0 seconds
"011": 3.5 seconds
"100": 4.0 seconds
The initial value is reverted to if a value outside of the setting range is 
set.

0

3.0 seconds

FAX initial 
setting

1
0

7

1

M Setting of the time of 

the transmission/
reception error sound

Transmission error sound sounding interval
"0": Every 0.3 seconds
"1": Every 0.7 seconds
Sounding time and paper feeding time are the same.

0

Every 0.3 seconds

FAX initial 
setting

2-3

Communication results 
sheet print settings (for 
ordinary transmission)
<FAX only>

This sets outputting of the communication results sheet following 
transmission (excluding successive broadcast, successive polling and 
relay broadcast transmission).
"00": Do not print
"01": Always print
"10": At times of transmission failure
The initial value is reverted to if a value outside of the setting range is 
set.

1

At times of 
transmission failure

FAX initial 
setting

0

4-5

Setting of the 
communication results 
sheet printing (at times 
of broadcast 
transmission)

This sets outputting of the communication results sheet at times of 
successive broadcast, successive polling and relay broadcast 
transmission.
"00": Do not print
"01": Always print
"10": Failed transmission address
The initial value is reverted to if a value outside of the setting range is 
set.

0

Always print

FAX initial 
setting

1

6-7

Communication results 
sheet print setting 
(when receiving)
<FAX only>

This sets outputting of the communication results sheet for when 
communications are received (excluding confidential communications).
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is 
set.

0

Do not print

FAX initial 
setting

0

8

Report output (when 
receiving confidential 
communications) 
<FAX only>

Setting to determine whether or not to output the communication results 
sheet (receiving) when confidential communications are received.
"1": Print
"0": Do not print
This only functions when the communication results sheet print setting 
(receiving) is set to be outputted.

0

Print

FAX initial 
setting

8

1-2

Print document 
contents when 
transmitting (results 
sheet)
<FAX only>

Setting to determine whether or not to print part of the transmitted 
document on the communication results sheet (transmission) when 
FAX transmission error occurs.
"00": Do not print
"01": Always print
"10": At times of error
The initial value is reverted to if a value outside of the setting range is 
set.
This functions when the communication results sheet print setting 
(ordinary transmission) (broadcast transmission) is set to be outputted.

1

At times of error

FAX initial 
setting

0

3

Automatic printing of 
the record sheet when 
memory is full.

Setting to determine whether or not to automatically output the 
communication record sheet when transmitted and received data on the 
FAX/Internet FAX communication record sheet reach 200 entries.
"0": No (do not output)
"1": Yes (automatically output)
If the data are not outputted, then new data are written over the 
previous data starting from the oldest of the 200 entries.
Trigger printing of 200 entries.

0

No

FAX initial 
setting

4-8

Printing of the 
communication record 
sheet at a designated 
time (hours)

Set the hours part of the designated time (hours and minutes) for 
outputting the communication record sheet.
Setting can be made over the range of 0 to 23 (hours) in 1-hour 
increments by binary inputting. The initial value of 0 hour is reverted to if 
a value outside of the setting range is set.

0

0 hour

FAX initial 
setting

0
0
0
0

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 22

9

1-6

Printing of the 
communication record 
sheet at a designated 
time (minutes)

Set the minutes part of the designated time (hours and minutes) for 
outputting the communication record sheet.
Setting can be made over the range of 0 to 59 (minutes) in 1-minute 
increments by binary inputting. The initial value of 0 minute is reverted 
to if a value outside of the setting range is set.

0

0 minute

FAX initial 
setting

0
0
0
0
0

7

Printing of the 
communication record 
sheet at a designated 
time

Setting to determine whether or not to output the communication record 
sheet at a designated time.
"1": Output the communication record sheet at a designated time
"0": Do not output the communication record sheet at a designated 
time. Even if designated time printing is set, do not output when the 
designated time coincides with the nighttime FAX mode.

0

Do not output

FAX initial 
setting

8

M ECM (valid except 

during V.34: reflected 
in the V.21 DIS/DCS/
DTC)

Setting to determine whether or not to execute the error re-send mode.
However, this is only valid when communication is other than V.34.
"1": No. Set with no ECM function.
"0": Yes. Set with ECM function.
ECM is on during communication in the V.34 mode.

0

Yes

FAX initial 
setting

10

1-8

M Remote changeover 

number setting

Set by binary inputting the number for receiving remote changeover 
from external telephones.
However, the remote changeover number is "XX*" with * fixed.
Adopt * when "A" is inputted.
Adopt # when "B" is inputted.
For bits 1-4, fix the upper digit of the remote changeover number. (0-F)
For bits 5-8, fix the second lowest digit of the remote changeover 
number. (0-F)
When C-F are set, the initial value is reverted to.

0

5*

FAX initial 
setting

1
0
1
1
0
1
0

11

1-4

M Distinctive ring (DRD 

setting)

Setting to determine whether or not to execute FAX arrival call by the 
distinctive ring.
Even if a call signal other than the set pattern is detected, there will be 
no automatic arrival call.
"0000": OFF
"0001": STANDARD
"1000": Pattern 1
"0100": Pattern 2
"1100": Pattern 3
"0010": Pattern 4
"1010": Pattern 5
"0110": ON (Australia) 
"1110": ON (New Zealand) 
"1001": ON (Hong Kong) 
When contents other than the above are set, the initial value is reverted 
to. 

0

OFF

FAX initial 
setting

0
0
0

5-8

M Not used

0
1
1
0

12

1-2

M Not used

0
0

3-4

M PBX setting

Setting to determine whether or not to send out ID or Flash before 
dialing.
Functions only in Germany and France.
In other countries, this setting is fixed to "OFF".
"00": OFF
"01": Flash
"10": ID
The setting other than the above would be granted as the default.

0

No (invalid)

FAX initial 
setting

0

5-8

M ID (number) setting

<Input the 1st digit 
when dial inputting and 
dialing>

Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW12-3, 12-4.
The initial value of 0 is reverted to if a value outside of the setting range 
(0-15) is set.

0

FAX initial 
setting

0
0
0

13

1-4

M ID (number) setting 2

<Input the 2nd digit 
when dial inputting and 
dialing>

Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW12-3, 12-4.
Do not use as the ID number when a value outside of the setting range 
(0-15) is set.
"-" when 13 is set.

1

FAX initial 
setting

1
0
1

5-8

M ID (number) setting 3

<Input the 3rd digit 
when dial inputting and 
dialing>

Conduct ID No. setting when the PBX function is valid.
Valid when ID is set using SW12-3, 12-4.
When 10-12, 14, 15 are designated, do not use numbers with those 
digits.
"-" when 13 is set.

1

FAX initial 
setting

1
0
1

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 23

14

1

M External telephone 

connection

Setting to determine whether or not to use an external telephone.
If "Yes" is not set using this switch, an external telephone cannot be 
used.
"0": No (invalid)
"1": Yes (valid)
The user cannot set without an external telephone. 

1

Yes

FAX initial 
setting

2-8

M Not used

0
1
0
0
0
0
0

15

1-8

M Signal sending level

Set the level adjustment for sending signals from the modem. Setting 
can be made over the range of 0 to 26 in 1dBm increments by binary 
inputting.
Since the maximum level differs according to country, if a value above 
the maximum level is set, the maximum value for the present country 
code will be adopted.

0

"00001010": -10dBm 
(North America/China/
Singapore/Thailand/
Malaysia/Philippine/
Hong Kong/Middle 
East/Other3)
"00001001": -9dBm 
(U.K./France/
Germany/Sweden/
Finland/Norway/
Denmark/
Netherlands/Italy/
Switcherland/Austria/
Indonesia/Slovakia/
South Africa/Spain/
Portuguese/
Luxemburg/Belgium/
Czech/Hungary/
Greece/Poland)
"00001011": -11dBm 
(Australia/New 
Zealand/India/Taiwan)
"00001110": -14dBm 
(Rusia)

Adjustment 
value

0
0
0
1
0
1
0

16

1-4

Not used

"0000": North America/Taiwan/Middle East/Other3/Rusia/South Africa
"0001": China/Hong Kong
"0011": India
"0101": Indonesia/Thailand/Malaysia/Philippine
"0110": Singapore
"1000": U.K./France/Germany/Sweden/Finland/Norway/Denmark/
Netherlands/Italy/Switcherland/Austria/New Zealand/Slovakia/Spain/
Portuguese/Luxemburg/Belgium/Czech/Hungary/Greece/Poland
"1010": Australia

0
0
0
0

5-6

M 1300Hz detection time

Set the time for determining that the signal (1300Hz), which is 
transmitted by the exchange (NTT) when binding the contract for F-net, 
has been detected.
"00": 2.5sec
"01": 3.0sec
"10": 1.5sec
"11": 2.5sec

0

2.5sec

0

7-8

Not used

0
0

17

1

M Automatic reduced 

transmission

In cases where the transmitted document size (width) is larger than the 
FAX paper size (width) of the other party’s machine, this setting 
determines whether to reduce the transmitted document or to cut off 
both edges.
"0": Transmit in reduced size
"1": Do not transmit in reduced size

0

Transmit in reduced 
size.

FAX 
transmission 
setting

2

Rotated transmission 
selection (A4 

→ A4R)

Rotated transmission or not depending on orientation of the document.
When transmitting A4 document, this setting determines whether to 
transmit as A3 width (A4) or to rotate the read image and transmit as A4 
width (A4R).
"0": Rotate
"1": Do not rotate

0

Rotate

FAX 
transmission 
setting

3

 Rotated transmission 
selection (B5R 

→ B5)

Rotated transmission or not depending on orientation of the document.
When transmitting B5R document, this setting determines whether to 
transmit as A4 width (B5R) or to rotate the read image and transmit as 
B4 width (B5).
"0": Rotate
"1": Do not rotate

0

Rotate

FAX 
transmission 
setting