DOWNLOAD Sharp MX-FXX1 (serv.man2) Service Manual ↓ Size: 4.79 MB | Pages: 80 in PDF or view online for FREE

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 8

* A to I: The greater the adjustment value is, the greater the image

loss is. 1step=0.1mm

 

 

66-1

: Setting

Function (Purpose) : Used to display the FAX-related soft SW on

the LCD to allow changing the soft SW
while checking with the LCD.

: FAX

: Setting

1)

When the machine enters Simulation 66-01, the screen on the
right is displayed.

2)

When [SW NO] is entered with 10-key, "6" is displayed in the
column of [SW NO].
* (In this example, "6" is entered.)
* (The range of value to be entered is 2  to 170.)
* When [C] key is pressed, the entered value of [SW NO] is

cleared.

3)

When [DATA] button is pressed, the data of soft SW No. 6 are
displayed.
* When [SW NO] button is pressed, the display returns to the

initial screen.

4)

The data of soft SW can be changed with 10-key.
* When 10-key corresponding to the bit is pressed, the bit

data are displayed as follows:
[1] 

→ [0]

[0] 

→ [1]

*  When [SW NO] button is pressed, the display returns to the

initial screen.

5)

When [EXECUTE] button is pressed, it is highlighted and the
setting is saved.
After saving the setting, [EXECUTE] button returns to the nor-
mal display.

 

66-2

: Setting

Function (Purpose) : Used to enter a country code and set the

default value for the country code.

: FAX

: Setting

1)

When the machine enters Simulation 66-02, the following
screen is displayed.
* When [DEST CODE] button is pressed, the display is shifted

to the country code list screen.

* The country code shift screen is shown on the next page.
* The currently set country code is displayed in the column of

"PRESENT:".

2)

Enter the country code (8 digits) with 10-key([0]/[1]). The
entered country code is displayed in the column of "NEW:" and
[SET] key becomes active.
* When [C] key is pressed, the column of “NEW:” is cleared.

3)

When [SET] button is pressed after entering the country code,
[EXECUTE] button becomes active. The country code is dis-
played in the column of "PRESENT:", and the column of
"NEW:" is cleared.
* When [C] key is pressed, the display returns to the initial set-

ting screen.

4)

When [EXECUTE] button is pressed, it is highlighted and
[YES] and [NO] buttons become active. The country name is
displayed on the tile line.
* When [NO] button is pressed, [EXECUTE] button returns to

the normal display and [YES] and [NO] buttons become
inactive.

5)

When [YES] button is pressed, it is highlighted and the soft SW
corresponding to the country code is initialized.
* During clearing the FAX-related soft SW, [EXECUTE] and

[YES] buttons are highlighted.

6)

After completion of initialization of the soft SW, [EXECUTE],
[YES], and [NO] buttons become inactive.
* When [CA] key is pressed after completion of initialization of

the soft SW, the whole machine is reset.

* When [DEST CODE] button is pressed on the initial screen, the

display is shifted to the country code list screen.
Use [

↑] [↓] buttons to select the country select page.

When the table item is the top (last)item, [

↑] [↓] buttons gray out.

When [

↑] [↓] buttons gray out, they are disabled.

* Press [BACK] button to return to the entry screen.

SCANNER 
mode (FAX, 
other than 
COPY)

A

Image  loss 
setting OC

LEAD_EDGE(OC)

OC lead edge image loss setting

0 to 100

0 (0mm)

B

FRONT_REAR(OC)

OC side image loss setting

0 to 100

0 (0mm)

C

TRAIL_EDGE(OC)

OC rear edge image loss setting

0 to 100

0 (0mm)

D

Image  loss 
setting SPF 
SIDE1

LEAD_EDGE(SPF_SIDE1)

Front surface lead edge image loss setting 

0 to 100

0 (0mm)

E

FRONT_REAR(SPF_SIDE1)

Front surface side image loss setting 

0 to 100

0 (0mm)

F

TRAIL_EDGE(SPF_SIDE1)

Front surface rear edge image loss setting 

0 to 100

0 (0mm)

G

Image  loss 
setting 
SPFSIDE2

LEAD_EDGE(SPF_SIDE2)

Back surface lead edge image loss setting 

0 to 100

0 (0mm)

H

FRONT_REAR(SPF_SIDE2)

Back surface side image loss setting 

0 to 100

0 (0mm)

I

TRAIL_EDGE(SPF_SIDE2)

Back surface rear edge image loss setting 

0 to 100

0 (0mm)

CLOSE

0

A:

SIMULATION

NO.50

㧙27

SCANNER/FAX-SEND ALL EDGE ADJUSTMENT VALUE

30

㨇 0㨪

100

㨉

OK

TEST

FAX

SCANNER

A

㧦

30

㧧 LEAD_EDGE(OC)

B

㧦

20

㧧 FRONT_REAR(OC)

C

㧦

20

㧧 TRAIL_EDGE(OC)

D

㧦

30

㧧 LEAD_EDGE(SPF_SIDE1)

SIMLATION NO.66-01

TEST

FAX SOFT SW. SETTING.

CLOSE

EXECUTE

SW No.

DATA

㧦

㧦

1 2 3 4 5 6 7 8

(SW No.2-170)

JAPAN

00000000

U.S.A.

10110101

AUSTRALIA

00001001

U.K.

10110100

FRANCE

00111101

GERMANY

00000100

SWEDEN

10100101

NEWZEALAND

01111110

CHINA

00100110

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 9

Initial screen

Country code list screen

 

66-3

: Operation test/Check

Function (Purpose) : Used to execute the read/write check of

EEPROM on the MODEM controller,
SDRAM, SRAM on the MFP controller, and
flash ROM, and to display the results.

: FAX

: Operation

1)

When the machine enters Simulation 66-03, the following
screen is displayed.
* Use [

↑] [↓] buttons to select the country select page. (The

highlighted section of the set value is switched and dis-
played on the set setting area.)
When [

↑] [↓] buttons gray out, they are disabled.

2)

When the memory check item button is selected, the display is
shifted to the memory check screen.
* Only one memory check item can be selected.

3)

When [EXECUTE] button is pressed, it is highlighted and the
memory check of the selected item is started.
* When [EXECUTE] button is pressed again during memory

check, the operation is interrupted. (The display shows the
status immediately before pressing [EXECUTE] button.)
When [EXECUTE] button is pressed after interrupting the
operation, memory check is resumed.

4)

After completion of memory check, [EXECUTE] button returns
to the normal display and the result of memory check is dis-
played.
* For the memory which is not installed, [NO CHECK] is dis-

played.

* In the case of [REPEAT] check, the following display is made for

every execution.
CHECKING 0001
CHECKING 0002
CHECKING 0003
  :
  :
The number of times is displayed in 4-digit decimal numbers.
When the number exceeds 9999, it becomes 0000
Check is repeated until [EXECUTE] is pressed or [NG] occurs.

The number in < > indicates the line.

SINGAPORE

10011100

TW

11111110

OTHER1

11111101

OTHER2

11111100

OTHER3

11111011

FINLAND

00111100

NORWAY

10000010

DENMARK

00110001

NETHERLANDS

01111011

ITALY

01011001

SWITZERLAND

10100110

AUSTRIA

00001010

INDONESIA

01010100

THAILAND

10101001

MALAYSIA

01101100

INDIA

01010011

PHILIPPINES

10001001

HONGKONG

01010000

RUSSIA

10111000

SOUTHAFRICA

10011111

SPAIN

10100000

PORTUGUESE

10001011

LUXEMBURG

01101001

BELGIUM

00001111

CZECH

00101110

HUNGARY

01010001

GREECE

01000110

POLAND

10001010

SIMULATION

 NO.66-02

TEST

FAX

SOFT

SW.CLEAR(WITH

 ADJUSTMENT

VALUE).

  CHINA

CLOSE

PRESENT

00000000

㧦

㧦

NEW

㧦

SET

EXECUTE

DEST

 CODE

ARE

YOU

SURE?

YES

NO

SIMULATION NO.66-02

TEST

FAX SOFT SWITCH CLEAR

CLOSE

JAPAN

:00000000

U.S.A

:10110101

AUSTRALIA

:00001001

U.K

:10110100

FRANCE

:00111101

GERMANY

:00000100

SWEDEN

:10100101

NEWZELAND

:01111110

CHINA

:00100110

SINGAPORE

:10011100

TW

:11111110

OTHER1

:11111101

BACK

NO CHECK

No check

CHECKING

During checking

OK

Check complete OK

NG A##

Check complete NG

Error occurring address or data 
line is displayed for each item. 

1

All Memory Device Check (Once)

All the items are checked 
once. 

2

MFP SRAM (Once)

Check only once

3

MFP SRAM (Repeat)

Repeat check

4

MFP FLASH + OP.FLASH (Once)

Check only once

5

MFP FLASH + OP.FLASH (Repeat)

Repeat check

6

MODEM EEPROM <1> (Once)

Check only once in LINE1

7

MODEM EEPROM <1> (Repeat)

Repeat check in LINE1

8

MODEM SDRAM <1> (Once)

Check only once in LINE1

9

MODEM SDRAM<1>(Repeat)

Repeat check in LINE1

10

MODEM EEPROM <2> (Once)

Check only once in LINE2

11

MODEM EEPROM <2> (Repeat)

Repeat check in LINE2

12

MODEM SDRAM <2> (Once)

Check only once in LINE2

13

MODEM SDRAM <2> (Repeat)

Repeat check in LINE2

CLOSE

SIMULATION NO.66-03

TEST

FAX PWB MEMORY CHECK

All Memory Device Check (once)

MFP SRAM (once)

MFP FLASH + OP.FLASH (repeat)

MODEM EEPROM<1> (once)

MODEM EEPROM<1> (repeat)

MFP SRAM (repeat)

MFP FLASH + OP.FLASH (once)

MODEM SDRAM<1> (once)

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 10

 

66-4

: Operation test/Check

Function (Purpose) : Used to send the selected signals to the

line and the main unit speaker. (Send level:
max.) 

: FAX

: Operation

1)

When the machine enters Simulation 66-04, the screen on the
right is displayed. (Default, left upper selected.)
* Use [

↑] [↓] buttons to switch the send mode select page.

When the selected item is the top (last)item, [

↑] [↓] buttons

gray out. (The highlighted section of the set value is
switched and displayed on the set setting area.)
When [

↑] [↓] buttons gray out, they are disabled.

2)

When a button of a signal to be sent is selected, it is high-
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.

3)

When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.

4)

To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.

 

66-5

: Operation test/Check

Function (Purpose) : Used to send the selected signal to the line

and the main unit speaker. (Send level: Soft
SW setting) (For the kinds of send signals,
refer to PART1 and PART2 of SIM66-04.)

: FAX

: Operation

1)

When the machine enters Simulation 66-05, the following
screen is displayed. (Default, left upper selected)
* Use [

↑] [↓] buttons to switch the send mode select page.

When the selected item is the top (last)item, [

↑] [↓] buttons

gray out. (The highlighted section of the set value is
switched and displayed on the set setting area.)

When [

↑] [↓] buttons gray out, they are disabled.

2)

When a button of a signal to be sent is selected, it is high-
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.

3)

When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.

4)

To end signal send:
* When [EXECUTE] button is pressed, it is highlighted and

signal send is interrupted.

 

66-6

: Data output/Check

Function (Purpose) : Used to print the confidential registration

check table (BOX NO., BOX name, pass-
code. (If there is no confidential registra-
tion, no print is made.)

: FAX

: Data (Confidential passcode)

1)

When [EXECUTE] button is pressed, it is highlighted and the
confidential checkable is printed.
* If there is no confidential registration, no print is made even

though [EXECUTE] key is pressed.

2)

After completion of printing, [EXECUTE] button returns to the
normal display.

* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key is

pressed during printing, the operation is interrupted.

 

66-7

: Data output/Check

Function (Purpose) : Used to output all image data saved in the

image memory. (Confidential data are also
outputted.)

: FAX

: Data (Image data)

1)

When [EXECUTE] button is pressed, it is highlighted and all
image data saved in the image memory are outputted.
* The confidential data are also outputted.

After completion of printing, the image data are not cleared.

* If there is no image memory, no print is made though [EXE-

CUTE] button is pressed.

2)

After completion of printing, [EXECUTE] button returns to the
normal display.

NOSIGNAL

33.6 V34

31.2 V34

28.8 V34

26.4 V34

24.0 V34

21.6 V34

19.2 V34

16.8 V34

14.4 V34

12.0 V34

9.6 V34

7.2 V34

4.8 V34

2.4 V34

14.4 V33

12.0 V33

14.4 V17

12.0 V17

9.6 V17

7.2 V17

9.6 V29

7.2 V29

4.8 V27t

2.4 V27t

0.3 FLG

CED 2100

CNG 1100

0.3 V21

ANSam

RINGER

No RBT

DP MAKE

DP BRK

NO MSG

28.8 V34

33.6 V34

NOSIGNAL

EXECUTE

CLOSE

SIMULATION

 NO.66-04

TEST

SIGNAL OUTPUT CHECK. (LEVEL MAX)

31.2 V34

26.4 V34

21.6 V34

19.2 V34

16.8 V34

12.0 V34

9.6 V34

7.2 V34

2.4 V34

14.4 V33

24.0 V34

14.4 V34

4.8 V34

28.8 V34

33.6 V34

NOSIGNAL

EXECUTE

CLOSE

SIMULATION NO.66-05

TEST

SIGNAL OUTPUT CHECK. (SOFT SW)

31.2 V34

26.4 V34

21.6 V34

19.2 V34

16.8 V34

12.0 V34

9.6 V34

7.2 V34

2.4 V34

14.4 V33

24.0 V34

14.4 V34

4.8 V34

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 11

* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key is

pressed during printing, the operation is interrupted.

 

66-8

: Operation test/Check

Function (Purpose) : Used to send the selected sound mes-

sages to the line and the speaker. (Send
level: Max.)

: FAX

: Operation

1)

When the machine enters Simulation 66-08, the following
screen is displayed. (Default, left upper selected)

2)

When the sound message button to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
* When [EXECUTE] button is pressed, it is highlighted and a

sound message is sent.

* When [EXECUTE] button is pressed, it is returns to the nor-

mal display and sending a sound message is interrupted.

 

66-9

: Operation test/Check

Function (Purpose) : Used to send the selected sound message

to the line and the speaker. (Send level:
max.)
* For details of sound messages, refer to
the sound message table of SIM66-08.

: FAX

: Operation

1)

When the machine enters Simulation 66-09, the following
screen is displayed. (Default, left upper setting)

2)

When a button of a sound message to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.

3)

When [EXECUTE] button is pressed, it is highlighted and a
sound message is sent.

4)

To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.

 

66-10

: Data clear

Function (Purpose) : Used to clear all image data saved in the

FAX image memory. (The confidential data
are also cleared.)

: FAX

: Clear (Image data)

1)

Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.

2)

Press [YES] button.
The image memory is cleared. [YES] button is highlighted.
* When [NO] button is pressed, [EXECUTE] button returns to

the normal display and [YES] and [NO] buttons gray out.

* During clearing the image memory, [EXECUTE] and [YES]

buttons are highlighted.
The image memory can be cleared even if there is no image
data.

3)

After completion of clearing, press [CA] key to reboot the
machine.

 

66-11

: Operation test/Check

Function (Purpose) : Used to send the selected signal at 300bps

to the line and the speaker. (Send level:
Max.)

: FAX

: Operation

1)

When the machine enters Simulation 66-11, the following
screen is displayed. (Default, left upper setting)

2)

When a button of a sound message to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.

3)

When [EXECUTE] button is pressed, it is highlighted and a
sound message is sent.

4)

To end signal send:

NONE (Mute)

PAUSE (Pause 
melody)

MESSAGE1 
(Message 1)

MESSAGE2 
(Message 2)

MESSAGE3 
(Message 3)

MESSAGE4 
(Message 4)

MESSAGE5 
(Massage 5)

MESSAGE6 
(Message 6)

ALARM (Alarm)

RINGER 
(Ringing sound 
(Speaker))

EXT.TEL.RING
ER (External 
telephone call)

CLOSE

EXECUTE

MESSAGE2

PAUSE

NONE

SIMULATION NO.66-08

TEST

MESSAGE OUTPUT CHECK. (LEVEL MAX)

MESSAGE1

MESSAGE3

MESSAGE5

MESSAGE6

ALARM

EXT.TEL.RINGER

MESSAGE4

RINGER

CLOSE

EXECUTE

MESSAGE2

PAUSE

NONE

SIMULATION

 NO.66-09

TEST

MESSAGE

 OUTPUT CHECK.(SOFT SW.)

MESSAGE1

MESSAGE3

MESSAGE5

MESSAGE6

ALARM

EXT.TEL.RINGER

MESSAGE4

RINGER