DOWNLOAD Sharp MX-FXX1 (serv.man2) Service Manual ↓ Size: 4.79 MB | Pages: 80 in PDF or view online for FREE

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 12

When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.

 

66-12

: Operation test/Check

Function (Purpose) : Used to send the selected signal at 300bps

to the line and the speaker. (Send level:
Soft SW setting)
* For the kings of send signals at 300bps,
refer to SIM66-11, 300bps send signal
table.

: FAX

: Operation

1)

When the machine enters Simulation 66-12, the following
screen is displayed. (Default, left upper setting)

2)

When a button of a sound message to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.

3)

When [EXECUTE] button is pressed, it is highlighted and a
sound message is sent.

4)

To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.

 

66-13

: Setting

Function (Purpose) : Used to register dial numbers for SIM66-

14/15/16, Dial test. (Up to 20 digits can be
registered.)

: FAX

: Data (Registration)

1)

When the machine enters Simulation 66-13, the following
screen is displayed.
* The number saved in the memory is displayed in the column

of [PRESENT:]. (If there is no data, [-------] is displayed.)

2)

Enter a number with 10-key.
The entered number is displayed in the column of [NEW:].
After entering 20 digits, 10-key is disabled (no response). Only
[C] key is enabled. (10-key [0] to [9], [*], [#], [C] key (back by
one digit))

3)

When [SET] key is pressed after completion of entry, the
entered number is displayed (registered) in the column of
[PRESENT:]. The column of [NEW:] becomes blank.
* If the "NEW:" column is blank, SET is inactive. When a value

is entered to the "NEW:" column, it becomes active.

 

66-14

: Adjustment

Function (Purpose) : Used to execute the dial pulse (10PPS)

send test and to adjust the make time.

: FAX

: Operation

1)

When the machine enters Simulation 66-14, the following
screen is displayed.
* Enter the make time (0 to 15) with 10-key and press [OK]

button, and the entered make time is temporality saved.

* Enter the make time (0 to 15) with 10-key and press [EXE-

CUTE] button instead of [OK] button, and [EXECUTE] but-
ton is highlighted and the dial pulse is sent from the line in
the set make time.

2)

When [EXECUTE] button is pressed, it is highlighted and the
dial pulse is sent from the line in the set make time.
* The dial pulse in this example is up to 20 digits registered

with SIM66-13.

3)

To end the dial test, press [EXCUTE] button again. The button
returns to the normal display and the test is terminated.
Also when dialing the number is completed, [EXECUTE] but-
ton returns to the normal display and the test is terminated.

 

66-15

: Adjustment

Function (Purpose) : Used to execute the dial pulse (20PPS)

send test and to adjust the make time.

: FAX

: Operation

1)

When the machine enters Simulation 66-15, the following
screen is displayed.
* Enter the make time (0 to 15) with 10-key and press [OK]

button, and the entered make time is temporality saved.

* Enter the make time (0 to 15) with 10-key and press [EXE-

CUTE] button instead of [OK] button, and [EXECUTE] but-
ton is highlighted and the dial pulse is sent from the line in
the set make time.

2)

When [EXECUTE] button is pressed, it is highlighted and the
dial pulse is sent from the line in the set make time.

NO SIGNAL

11111

11110

00000

010101

00001

CLOSE

EXECUTE

00000

11111

NO SIGNAL

SIMULATION

 NO.66-11

TEST

300bps SIGNAL OOUTPUT. (LEVEL MAX.)

11110

010101

00001

CLOSE

EXECUTE

00000

11111

NO SIGNAL

SIMULATION

 NO.66-12

TEST

300bps SIGNAL OOUTPUT. (SOFT

 SW.)

11110

010101

00001

A:

A

㧦 4

㧧 MAKE TIME [+29ms]

SIMULATION NO.66-14

DIAL TEST(10PPS)

4

㨇 0㨪 15㨉

OK

TEST

CLOSE

EXECUTE

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 13

* The dial pulse in this example is up to 20 digits registered

with SIM66-13.

3)

To end the dial test, press [EXCUTE] button again. The button
returns to the normal display and the test is terminated.
Also when dialing the number is completed, [EXECUTE] but-
ton returns to the normal display and the test is terminated.

 

66-16

: Adjustment

Function (Purpose) : Used to execute the DTFM signal send test

and to adjust the send level.

: FAX

: Operation

1)

When the machine enters Simulation 66-16, the following
screen is displayed.
* Item A (High group frequency) and item B (High-Low group

frequency) are selected with [

↑] [↓] buttons. When the

selected item is the top (last) item, [

↑] [↓] buttons gray out.

(The highlighted section of the set value is switched and dis-
played on the set setting area.)
When [

↑] [↓] buttons gray out, they are disabled.

* Enter the High group or High - Low group (0 to 15) with 10-

key and press [OK] button. The set sign send level is tempo-
rality saved.

* Enter the single send level (0 to 15) with 10-key and press

[EXECUTE] button instead of [OK] button, and [EXECUTE]
button is highlighted and the dial pulse is sent from the line
by the setting of high group or low group.

2)

When [EXECUTE] button is pressed, it is highlighted and the
dial pulse signal is sent from the line by the setting of high/low
group of the signal send level.

3)

To terminate the dial test, press [EXECUTE] button. The button
returns to the normal display and the test is terminated.
When dialing the dial number is completed, [EXECUTE] button
returns to the normal display and the test is terminated.

 

66-17

: Operation test/Check

Function (Purpose) : Used to send the DTMF signal to the line

and the speaker. (Send level: Max.)

: FAX

: Operation

1)

When the machine enters Simulation 66-17, the following
screen is displayed. (Default, left upper selected)

2)

When a button of a send signal is selected, it is highlighted and
the previously set button returns to the normal display.
* Only one kind of signal to be sent can be selected.

3)

When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
* When another signal send button is pressed during sending

signals, the send signal can be changed.

4)

To stop signal sending:
When [EXECUTE] button is pressed, it returns to the normal
display and signal sending is interrupted.

 

66-18

: Operation test/Check

Function (Purpose)

: Used to send the DTMF signal to the line

and the speaker. (Send level: Soft SW set-
ting)

: FAX

: Operation

1)

When the machine enters Simulation 66-18, the following
screen is displayed.

2)

When a button of a send signal is selected, it is highlighted and
the previously set button returns to the normal display.

3)

When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
* When another signal send button is pressed during sending

signals, the send signal can be changed.

4)

To stop signal sending:
When [EXECUTE] button is pressed, it returns to the normal
display and signal sending is interrupted.

 

66-19

: Backup

Function (Purpose) : Used to write the telephone book data

stored in HD into the FLASH ROM.

: FAX

: Data

1)

Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.

A:

A

㧦 4

㧧 MAKE TIME [+9ms]

SIMULATION NO.66-15

DIAL TEST(20PPS)

4

㨇 0㨪 15㨉

OK

TEST

CLOSE

EXECUTE

A:

A

㧦 4

B

㧦 4

㧧 HIGH(dB)

㧧 HIGH-LOW

SIMULATION

 NO.66-16

DIAL TEST(DTMF)

4

㨇 0㨪 15㨉

OK

TEST

CLOSE

EXECUTE

SIMULATION NO.66-17

TEST

DTMF SIGNAL OUTPUT.(LEVEL MAX)

EXECUTE

1

2

3

4

6

7

9

#

5

8

0

SIMULATION

 NO.66-18

TEST

DTMF SIGNAL OUTPUT.(SOFT

 SW)

EXECUTE

1

2

3

4

6

7

9

㧖

#

5

8

0

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 14

2)

Press [YES] button.
The telephone book data stored in HD are written into the
FLASH ROM. [YES] button is highlighted.
* When [NO] button is pressed, [EXECUTE] button returns to

the normal display and [YES] and [NO] buttons gray out.

* During execution of backup, [EXECUTE] and [YES] buttons

are highlighted.

3)

After completion of memory writing, [EXECUTE] button returns
to the normal display and [YES] and [NO] buttons gray out.

 

66-20

: Backup

Function (Purpose) : Used to write the telephone book data

stored in the FLASH ROM into HD.

: FAX

: Data

1)

Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.

2)

Press [YES] button.
The telephone book data stored in the FLASH ROM are writ-
ten into HD. [YES] button is highlighted.
* When [NO] button is pressed, [EXECUTE] button returns to

the normal display and [YES] and [NO] buttons gray out.

* During execution of read/write, [EXECUTE] and [YES] but-

tons are highlighted.

3)

After completion of memory writing, [EXECUTE] button returns
to the normal display and [YES] and [NO] buttons gray out.

 

66-21

: Check

Function (Purpose) : Used to print the selected items (various

registration information, communication
management information, file management
information, system error, protocol moni-
tor).

: FAX

: Data

1)

When an item button to be printed is selected, it is highlighted
and the previously set button returns to the normal display.
(Default select: Left upper)
* Only one item can be selected.

2)

Press [EXECUTE] button.
[EXECUTE] button is highlighted and printing is started.

* During printing an item, [EXECUTE] and the print item but-

ton are highlighted.

3)

After completion of printing, [EXECUTE] button returns to the
normal display.

* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key is

pressed during printing, the operation is interrupted.

 

66-22

: Setting

Function (Purpose) : Used to set the handset sound volume.

(This simulation can be executed even
though the handset setting is set to NO.
When, however, the handset is not
installed, the sound volume cannot be
checked.) (Japan model only)

: FAX

: Operation

1)

When the machine enters the simulation, the number of the set
sound volume is displayed. (In this example, MIDDLE is set as
the default sound volume.)

2)

Use 10-key to set the handset sound volume. (0: MIN 1:MID-
DLE 2:MAX)
* Enter the sound volume (0 to 2) with 10-key and press [OK]

button. The set sound volume is saved.

* Enter the sound volume (0 to 2) with 10-key and press [EXE-

CUTE] key instead of [OK] key. [EXECUTE] key is high-
lighted and the set sound volume is saved. The on-hold tone
is delivered in the set sound volume.

3)

Press [EXECUTE] button to deliver the selected on-hold tone.
* The sound message is outputted to the handset and an

external telephone. The speaker, however, is muted.

* Even during sending the on-hold tone ([EXECUTE] button is

highlighted), the sound volume can be changed by switching
the sound volume button.

* If, however, the handset is not installed, the sound volume

cannot be checked. Execution is possible.

4)

When [EXECUTE] button is pressed, it is highlighted and deliv-
ery of the on-hold tone is stopped.

SIMULATION

 NO.66-19

TEST

ADDRESS DATA BACK UP. (WRITE TO FLASH ROM)

CLOSE

EXECUTE

ARE

YOU

SURE?

YES

NO

SIMULATION

 NO.66-20

TEST

ADDRESS DATA BACK UP. (READ FROM FLASH ROM)

CLOSE

EXECUTE

ARE

YOU

SURE?

YES

NO

REGISTERED

MANAGEMENT

FILE MANAGEMENT

SYSTEM ERROR LINE 1

PROTOCOL LINE 1

SYSTEM ERROR LINE 2

PROTOCOL LINE 2

SIMULATION NO.66-21

TEST

FAX INFORMATION PRINT OUT.

REGISTERED

MANAGEMENT

PROTOCOL LINE 1

SYSTEM ERROR LINE 2

EXECUTE

PROTOCOL LINE 2

FILE MANAGEMENT

SYSTEM ERROR LINE 1

A:

A

1

(0:MIN 1:MIDDLE 2:MAX)

SIMULATION NO.66-22

HANDSET VOLUME SETTING

1

0

2

OK

TEST

CLOSE

EXECUTE

MX-FXX1  SIMULATIONS, FAX SOFTWARE SWITCH  5 – 15

 

66-24

: Data clear

Function (Purpose) : Used to clear the FAST save data.
Section

: FAX

: Data clear

1)

Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.

2)

Press [YES] button.
The FAST save data are cleared. [YES] button is highlighted.
* When [NO] button is pressed, [EXECUTE] button returns to

the normal display and [YES] and {NO} buttons gray out.

* During execution of the FAST save data clear, [EXECUTE]

and [YES] buttons are highlighted.

3)

After completion of memory clear, [EXECUTE] button returns
to the normal display and [YES] and {NO} buttons gray out.

 

66-25

: Setting

Function (Purpose) : Used to register the FAX number for

MODEM dial-in.

: FAX

: Data clear

1)

When the machine enters Simulation 66-25, the following
screen is displayed.
* The stored number is displayed in the column of

"PRESENT:". (If there is no data, [-------] is displayed.)

2)

Enter a number with 10-key.
Entry can be made up to 20 digits.
After entering 20 digits. 10-key is disabled. Only [C] key is
enabled.
The entered number is displayed in the column of "NEW:".
(10-key [0] to [9], [*], [#], [C] key (back by one digit))

3)

When [SET] button is pressed after completion of entering a
number, the entered umber is displayed (registered) in the col-
umn of "PREZENT:".
The column of "NEW:" becomes blank.
* When the column of "NEW:" is blank, [SET] becomes inac-

tive. When a number is entered to "NEW:", [SET] becomes
active.

 

66-26

: Setting

Function (Purpose) : Used to register external telephone num-

bers for MODEM dial-in.

: FAX

: Data (Registration)

1)

When the machine enters Simulation 66-26, the screen on the
right is displayed.
* The stored number is displayed in the column of

"PRESENT:". (If there data, [-------] is displayed.)

2)

Enter a number with 10-key. Entry can be made up to 20 digits.
After entering 20 digits. 10-key is disabled. Only [C] key is
enabled.
The entered number is displayed in the column of "NEW:". (10-
key [0] to [9], [*], [#], [C] key (back by one digit))

3)

When [SET] button is pressed after completion of entering a
number, the entered umber is displayed (registered) in the col-
umn of "PRESENT:".
The column of "NEW:" becomes blank.
* When the column of "NEW:" is blank, [SET] becomes inac-

tive. When a number is entered to "NEW:", [SET] becomes
active.

 

66-29

: Clear

Function (Purpose) : Used to initialize the telephone book data

(the one-touch registration table, the FTP/
Desktop expansion table, the group expan-
sion table, the program registration table,
the interface memory box table, the meta
data, InboundRouting, and the Documen-
tAdmin table).

: FAX

: Data (Initializing)

1)

Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.

2)

Press [YES] button.
The telephone book data area cleared. [YES] button is high-
lighted.
* When [NO] button is pressed, [EXECUTE] button returns to

the normal display and [YES] and [NO] buttons gray out.

* During the telephone book data clear, [EXECUTE] and

[YES] buttons are highlighted.

3)

After completion of memory clear, [EXECUTE] button returns
to the normal display and [YES] and [NO] buttons gray out.

SIMULATION NO.66-25

TEST

M-D-IN FAX NUMBER SETTING. 0-9[0-9].*:[*]:#:[#]

PRESENT

---------------------

NEW

:

:

SET

CLOSE

SIMULATION NO.66-26

TEST

M-D-IN EXTEL NUMBER SETTING. 0-9[0-9]*:[*]:#:[#]

PRESENT:

-----------------

NEW:

㧦

SET

CLOSE