DOWNLOAD Sharp MX-BMX1 Service Manual ↓ Size: 22.28 MB | Pages: 127 in PDF or view online for FREE

20 October 2010 

AREA  A

Removal Sensor Q3
1.  Remove Infeed cover (  

  3.3.2 ).

NOTE: Picture shows Infeed module removed for clarity. It is not necessary to 

remove Infeed module to replace Sensor Q3.

2.  Disconnect connector [A] to Sensor Q3 ( 

 x1 ).

3.  Remove sensor Q3 [B].

Replacement Sensor Q3
1.  Reverse the removal procedure.

Removal Back jogger module
1.  Remove Infeed module ( 

  3.4.1 ).

2.  Remove Infeed transport module ( 

  3.4.3 ).

3.  Remove the screw to plastic distance [C] (   x1 ).
4.  Unhook the Length adjustment strap wheel [D].

NOTE: DO NOT TURN THE ADJUSTMENT SCREW.

5.  Insert a screwdriver [E] in the shaft and unscrew the shaft [F] to the Back jog-

ger module (   x1 ).

 

NOTE: Rotate the screwdriver counterclockwise to unscrew the shaft.

6.  Remove the shaft [F].
7.  Remove the Back jogger module.

NOTE: If removing the Back jogger module completely, remove three cable 

ties to the Infeed sensor Q1 harness.

NOTE: When replacing the Back jogger module, make sure that the Back jogger 

fingers [G] and the Infeed bearing bracket [H] is in its right position.

1.  Reverse the removal procedure.

20 October 2010

AREA  A 

[C]

[D]

[B]

[E]

[F]

[G]

[H]

[ I ]

[J]

[E]

[P]

[O]

[O]

[A]

[K]

[L]

20 October 2010 

AREA  A

Removal
1.  Remove Back jogger module ( 

 3.4.9 )

2.  Loosen spring [A] with a screwdriver [B], by pulling the screwdriver straight out  

according to the arrows [C] (   x1 ).

3.  Remove screws [D] (   x2 ).
4.  Remove E-clips [E] (   x4 ).
5.  Pull out the Back jogger arm shaft [F].

NOTE: Make sure to notice the orientation of the Back jogger fingers [G], [H], 

[I] and [J], and the brass bracket [K].

6.  Remove nut [L] and dismount the Back jogger finger (   x1 ).

NOTE: There is two different kind of Back jogger fingers. One type with a 

bearing [M] and one type without a bearing [N].

Replacement
1.  Remount the Back jogger finger and tighten the nut [L] (   x1 ).

NOTE: Tighten the nut finger tight, then tighten the nut ½ revolution with a 19 

mm open wrench.

2.  Reinstall correct Back jogger finger [G], [H], [ I ] and [J], Bras bracket and the 

two bushings [O] on correct place.

NOTE: Make sure to turn the Brass bracket correctly, according to the circles 

in the picture.

3.  Slide Back jogger arm shaft [F] in place.

NOTE: Make sure to turn the shaft the correct way [ P].

4.  Reinstall E-clips [E] (   x4 ).
5.  Reinstall Back jogger arm module in place, and tighten screws [D] (   x2 ).
6.  Push the spring [A] back with your thumb.

NOTE: Make sure that the bearing is in the slot on the feather spring.

7.  Reverse the rest of the removal procedure.

[M]

[N]

20 October 2010

AREA  A 

Removal
1.  Remove Back jogger module ( 

 3.4.9 ).

2.  Remove screw [A] and nut [B] (   x1,   x1 ).
3.  Remove the Bracket [C] from the motor axel.
4.  Remove connector [D]  ( 

 x1).

5.  Remove screws [E] to the motor (   x3 ).

Replacement
1.  Reinstall screws [E] to the motor (   x3 ).
2.  Reinstall connector [D]  ( 

 x1).

3.  Reinstall screw [A] and nut [B] (   x1,   x1 ).

NOTE: Make sure that the screw [A] is positioned against  flat of the motor 

shaft. And that the motor shaft is level [F] with the Bracket [C].

4.  Reverse the rest of the removal procedure.

[E]

[B]

[A]

[D]

[F]

[C]