Sharp MX-BMX1 Service Manual ▷ View online
Replacement Adjustment
20 October 2010
3-23
AREA A
3.4.7 SIDE JOGGER MOTOR M3 & SENSOR Q12
Removal
1. Remove Infeed module (
1. Remove Infeed module (
3.4.1 ).
2. Remove connectors [A] (
x2 ).
3. Loosen allen screw [B] to pulley ( x1 ).
4. Remove screws [C] to motor bracket ( x2 ).
5. Remove Side jogger motor M3 & sensor Q12.
4. Remove screws [C] to motor bracket ( x2 ).
5. Remove Side jogger motor M3 & sensor Q12.
NOTE: The sensor Q12 is located on the motor.
Replacement
1. Push the pulley down, to make sure that it is in the right position.
2.
1. Push the pulley down, to make sure that it is in the right position.
2.
When installing the motor, make sure that the allen screw is positioned against
the flat [D] of the motor shaft.
3. Reverse the rest of the removal procedure.
[C]
[A]
[B]
[D]
20 October 2010
3-24
AREA A
3.4.8 SIDE GUIDE TRANSMISSION &SENSOR Q13
[B]
Continued on next page....
[A]
[D]
[C]
[E]
[F]
[G]
[H]
[I]
Replacement Adjustment
20 October 2010
3-25
AREA A
Removal Sensor Q13
1. Remove Infeed module (
1. Remove Infeed module (
3.4.1 ).
2. Disconnect connector [A] to sensor Q13 (
x1 ).
NOTE: Make sure that the side guides are in there most inner position and move
the Back jogger module by hand, to make it easier to get to the sensor.
Replacement
1. Reverse the removal procedure.
1. Reverse the removal procedure.
Removal Side guide transmission
1. Remove Side jogger motor (
1. Remove Side jogger motor (
3.4.7 ).
2. Loosen nuts [B] ( x2 ).
3. Use a screwdriver [C] to press the springs [D] together, to slack the drive belt
3. Use a screwdriver [C] to press the springs [D] together, to slack the drive belt
( x2, x1).
4. Tighten nuts [B] again ( x2 ).
5. Remove screwdriver [C] ( x1).
6. Remove connector [A] (
5. Remove screwdriver [C] ( x1).
6. Remove connector [A] (
x1 ).
7. Remove Side jogger home position sensor Q13 [E].
8. Use a flat plier to lift up the drive belt from the side guide brackets [F].
9. Remove the pulley [G] and the dive belt [H].
8. Use a flat plier to lift up the drive belt from the side guide brackets [F].
9. Remove the pulley [G] and the dive belt [H].
Replacement
1. Place the side guides in there outermost position [I].
2. Take the pulley [G], and press the drive belt into the left side guide bracket [F].
1. Place the side guides in there outermost position [I].
2. Take the pulley [G], and press the drive belt into the left side guide bracket [F].
Continue and press the drive belt into the right side guide bracket [F].
3. Loosen nuts [B], and let the springs [D] tensioning the drive belt ( x2, x2 ).
4. Tighten nuts [B] again ( x2 ).
5. Reverse the rest of the removal procedure.
4. Tighten nuts [B] again ( x2 ).
5. Reverse the rest of the removal procedure.
20 October 2010
3-26
AREA A
3.4.9 BACK JOGGER MODULE & SENSOR Q3
[D]
[C]
[E]
[F]
Continued on next page....
[B]
[A]
[C]
[G]
[ H ]
Click on the first or last page to see other MX-BMX1 service manuals if exist.