Sharp MX-BMX1 Service Manual ▷ View online
Replacement Adjustment
20 October 2010
3-15
COVERS
Adjustment
1. Loosen screw [D] ( x1 ) and screws [F] ( x2 ). Adjust so that the Top cover
1. Loosen screw [D] ( x1 ) and screws [F] ( x2 ). Adjust so that the Top cover
rests on the rubber supports [H] ( x3 ) when closed.
2. Loosen nuts [C] ( x4 ) and adjust so that the plate [I] holding the upper part
of the Top cover lock enters the cut-out in the front frame centered.
3. Check that the Top cover lock works without binding. Loosen screws and nuts
[J] ( x2 ) ( x2 ) to adjust upper part in/out. Loosen nuts [K] ( x2 ) to
adjust lower part up/down.
4. Check that the Top cover Interlock switch is correctly adjusted (
3.3.8 ).
[H]
[J]
[J]
[I]
[K]
20 October 2010
3-16
COVERS
3.3.8 INTERLOCK SWITCH S16 &S17
Removal
1. Remove Front cover (
1. Remove Front cover (
3.3.1 ).
2. Remove connector [A] (
x1 ).
3. Remove nuts [B] to Interlock box ( x2 ).
4. Remove screws [C] to Switch PCB ( x2 ).
4. Remove screws [C] to Switch PCB ( x2 ).
Replacement
1. Reverse the removal procedure.
1. Reverse the removal procedure.
Adjustment
1. Check that the Top cover is correctly adjusted (
1. Check that the Top cover is correctly adjusted (
3.3.5 ).
2. Loosen nuts [B] to Interlock box ( x2 ).
3. Adjust the Interlock box, so that Top cover activates interlock switch 2 mm /
3. Adjust the Interlock box, so that Top cover activates interlock switch 2 mm /
5/64” before closing.
4. Tighten nuts [B] to Interlock box ( x2 ).
5. Recheck step 3.
5. Recheck step 3.
[A]
[B]
WARNING
Overriding or cheating the interlock allows the MX-BMX1 system to operate
with the top cover open which can result in personal injury. Never give
the operator access to the cheater or show how overriding the interlock
system is carried out.
[C]
Replacement Adjustment
20 October 2010
3-17
AREA A
3.4 AREA A
3.4.1 INFEED MODULE
1. Remove Front and Rear cover (
3.3.1 ).
2. Remove Infeed cover (
3.3.2 ).
3. Remove connectors [A] (
x2 ).
4. Unhook of the length adjustment strap
[B].
5. Remove screws [C] on the Front side of the Booklet maker ( x2 ).
6. Remove screws [D] on the Rear side of the Booklet maker ( x2 ).
7. Pull out the Infeeder carefully.
6. Remove screws [D] on the Rear side of the Booklet maker ( x2 ).
7. Pull out the Infeeder carefully.
NOTE: Make sure that the Side jogger motor M3 is not catching the frame of the
Booklet maker.
[A]
[B]
[C]
[D]
20 October 2010
3-18
AREA A
3.4.2 PAPER INFEED SENSOR
1. Remove Infeed Module (
3.4.1 ).
2. Remove screw [A] ( x1 ).
NOTE: You do not have to remove the Infeed module to reach the screw, you
are able to reach the screw through the hole in the Infeed module.
3. Remove connector [B] (
x1 ).
[B]
[A]
Click on the first or last page to see other MX-BMX1 service manuals if exist.