Sharp MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) Service Manual ▷ View online
MX-5141N AR-SU1 (STAMP UNIT) 23 – 1
MX-5141N
Service Manual
[23] AR-SU1 (STAMP UNIT)
1. Unpacking
A. Remove the stamp unit
B. Packed items check
* When replacing the stamp cartridge, Refer to “Stamp cartridge
replacement” in the “User’s Guide” (PDF document) which is
stored in the hard disk of the machine. The user must be notified
of that. (Do not refer to “Stamp cartridge replacement procedure”
(Packed items).)
stored in the hard disk of the machine. The user must be notified
of that. (Do not refer to “Stamp cartridge replacement procedure”
(Packed items).)
2. Installation (RSPF model)
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Install the stamp unit
1)
Open the RSPF unit, and remove the OC mat.
For removing and fixing screws, use a stubby screwdriver.
* If stubby screwdriver is not available, loosen the screw of
the angle adjustment plate on the rear side of the machine,
and lower the angle adjustment plate and put the RSPF unit
straight.
and lower the angle adjustment plate and put the RSPF unit
straight.
2)
Remove the sensor cover. Remove the stamp case, and
remove the earth cord.
remove the earth cord.
No.
Name
Quantity
1
Stamp unit
1
2
Stamp cartridge replacement procedure*
1
3
Stamp cartridge
3
4
Installing screw
1
1
2
3
4
MX-5141N AR-SU1 (STAMP UNIT) 23 – 2
3)
Attach the stamp unit (Packed items) to the stamp case which
was removed from the RSPF unit with the installing screw
(Packed items). (Fix it together with the earth wire.)
was removed from the RSPF unit with the installing screw
(Packed items). (Fix it together with the earth wire.)
4)
Install the stamp case unit, and connect the connector.
5)
Install the sensor cover.
6)
Install the stamp cartridge (Packed items).
7)
Install the OC mat, and close the RSPF unit.
* If the angle adjustment plate was lowered for installation, lift
the angle adjustment plate, and fix it with the screw, and
close the RSPF unit.
close the RSPF unit.
B. Turn on the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
MX-5141N AR-SU1 (STAMP UNIT) 23 – 3
3. Installation (DSPF model)
A. Install the stamp unit
1)
Open the DSPF unit, remove the OC mat.
2)
Remove the screw, and remove the paper exit PG cover.
Remove the screw.
Remove the screw.
Disengage the pawl, and remove the stamp case unit.
3)
Attach the stamp unit (Packed items) to the stamp case which
was removed from the DSPF unit with the installing screw
(Packed items). (Fix it together with the earth wire.)
was removed from the DSPF unit with the installing screw
(Packed items). (Fix it together with the earth wire.)
* Arrange the harness of the stamp unit as shown below.
4)
Install the stamp case unit, and fasten it with the screw. Install
the earth wire. Connect the connector.
the earth wire. Connect the connector.
5)
Install the paper exit PG cover.
6)
Disengage the pawl, and open the stamp case unit.
Install the stamp cartridge (Packed items).
1
2
2
4
3
2
4
1
3
2
1
3
MX-5141N AR-SU1 (STAMP UNIT) 23 – 4
7)
Install the OC mat to the SPF glass, and close the DSPF unit.
B. Turn on the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
Click on the first or last page to see other MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) service manuals if exist.