Sharp MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) Service Manual ▷ View online
MX-5141N MX-PNX6A/B/C/D (PUNCH MODULE) 15 – 4
D. Check of the connected position of main unit
and finisher
1)
Engage the finisher that has installed punch unit to the main
unit, and temporarily fix.
unit, and temporarily fix.
* Insert the rail of the finisher unit into the rail reception fixture
of main unit, fix temporarily.
2)
Open the front door of punch unit.
3)
Check that the center of the screw hole of the punch unit is in
the range of specification of an oval hole of the mounting fix-
ture in front side of main unit.
the range of specification of an oval hole of the mounting fix-
ture in front side of main unit.
* When not the range of specification, progress to the proce-
dure of "F. Adjustment".
If the adjustment is not required, remove the screw from the
screw hole directly and push the caster into it until the instal-
lation fixing. (MX-FN11 only)
If the adjustment is not required, remove the screw from the
screw hole directly and push the caster into it until the instal-
lation fixing. (MX-FN11 only)
E. Adjustment
* Refer to the adjustment procedure of each finisher.
F. Install to main unit
1)
Engage the finisher that has installed punch unit to the main
unit.
unit.
2)
Open the front door of punch unit.
MX-5141N MX-PNX6A/B/C/D (PUNCH MODULE) 15 – 5
3)
Secure the main unit and the punch unit with the fixing screw
(Packed items of the MX-FN11).
(Packed items of the MX-FN11).
4)
Close the front door of punch unit.
5)
Install the fixing screw (Packed items of MX-FN11) on rear
side.
side.
6)
Install the rear cover of punch unit with the fixing screws.
7)
By using nippers, split the removed connector cover of the fin-
isher along the perforated line.
isher along the perforated line.
8)
Install the connector cover of the finisher and fix it with the fix-
ing screw.
ing screw.
G. Connection of connector to the main unit
1)
Connect two connectors of the finisher to the main unit, and
tighten the screws.
tighten the screws.
MX-5141N MX-PNX6A/B/C/D (PUNCH MODULE) 15 – 6
H. Punch position label attachment
1)
Attach the punch position label (Packed items of the MX-FN11)
to the position indicated in the figure.
to the position indicated in the figure.
For scanner
For DSPF/RSPF
I.
Turn on the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
DSPF
RSPF
R2.5 connection line
Edge line R 2.5
CAUTION
Cleaning of the document scan section
When streaks appear on copy or scan
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
Document scan section
MX-5141N MX-TU13 (EXIT TRAY CABINET) 16 – 1
MX-5141N
Service Manual
[16] MX-TU13 (EXIT TRAY CABINET)
1. Unpacking
A. Packed items check
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Paper exit tray attachment
1)
Open the front cabinet, and remove the front cabinet upper.
2)
Attach the paper exit tray (Packed items), and fix it with the
screw (Packed items).
screw (Packed items).
3)
Attach the front cabinet upper, and close the front cabinet.
4)
Attach the paper holding arm (Packed items).
5)
Attach the full detection actuator (Packed items).
NOTE: Be careful of the installing direction of the full detection
actuator.
6)
B. Turn ON the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
No.
Name
Quantity
1
Paper exit tray
1
2
Screw
4
3
Paper holding arm
1
4
Full detection actuator
1
5
Paper exit cover
1
2
1
3
4
5
!
Click on the first or last page to see other MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) service manuals if exist.