Sharp MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) Service Manual ▷ View online
MX-5141N MX-FN18 (SADDLE STITCH FINISHER) 14 – 9
4)
Remove the screw, and remove the connector cover on rear
side of the finisher.
side of the finisher.
5)
Install the Step screw B (Packed items (No.4)).
6)
Attach the connector cover on rear side of the finisher with the
fixing screw.
fixing screw.
G. Connection of connector to the main unit
1)
Connect two connectors of the saddle stitch finisher to the
main unit, and tighten the screws.
main unit, and tighten the screws.
H. Staple position label attachment
1)
Attach the staple position label (Packed items) to the position
indicated in the figure.
indicated in the figure.
For scanner (Packed items (No.9))
For DSPF/RSPF (Packed items (No.10))
I.
Turn on the power of the main unit
1)
Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
and turn ON the main power switch and the operation panel
power switch.
Fit with the corner R.
Label attachment reference
*Corner of the upper
cabinet bottom
Fit with the corner R.
DSPF
RSPF
Cleaning of the document scan section
CAUTION
When streaks appear on copy or scan
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
images, open the automatic document
feed unit and clean the document scan
section with the glass cleaner (accessory).
MX-5141N MX-PNX6A/B/C/D (PUNCH MODULE) 15 – 1
MX-5141N
Service Manual
[15] MX-PNX6A/B/C/D (PUNCH MODULE)
1. Unpacking
A. Pulling out of the punch unit
B. Removal of the protection material
1)
Remove the fixing tape and protection material.
2)
Open the front cover, and open the top cover.
3)
Remove the screws, and remove the fixing material. (2 posi-
tions)
tions)
4)
Close the top cover, and close the front cover.
1
2
1
2
MX-5141N MX-PNX6A/B/C/D (PUNCH MODULE) 15 – 2
C. Packed items check
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
NOTE: Before installing the punch unit, unpack the finisher.
A. Installation of punch unit
1)
Attach the step screw A (Packed items) to the finisher.
2)
Remove the fixing screw, and remove the connector cover on
rear side of the finisher.
rear side of the finisher.
3)
Hang the punch unit on the step screws installed to the fin-
isher.
isher.
4)
Tighten the step screws bundled to the punch unit, fix the
punch unit.
punch unit.
No.
Name
Quantity
1
P tight M4x12
1
2
Step screw A
2
3
Cap screw M3x6
3
4
Binding head M4x12
4
5
Front cover
1
6
Front cover mounting fixture
1
7
Connection fixture F (for punch)
1
8
Connection fixture R (for punch)
1
9
Guide mylar upper (Not used)
1
10
Guide mylar lower (Not used)
1
1
2
3
5
6
7
8
9
10
P
P
4
1
2
MX-5141N MX-PNX6A/B/C/D (PUNCH MODULE) 15 – 3
5)
Attach the front cover mounting fixture (Packed items) with the
fixing screws (Packed items).
fixing screws (Packed items).
Remove the screw of the finisher, and reuse it. Install it using
the reuse screw, and three fixing screws (Packed items) bun-
dled to punch unit.
the reuse screw, and three fixing screws (Packed items) bun-
dled to punch unit.
6)
Open the front door of punch unit.
7)
Engage the pawls of the rear side of front cover (Packed
items), attach the front cover with the fixing screw (Packed
items).
items), attach the front cover with the fixing screw (Packed
items).
B. Connection of connector of the finisher and
punch unit
1)
Remove the fixing screws, and remove the rear cover.
2)
Connect two connectors of the finisher to the PWB of punch
unit, and fix the harness to the clamp.
unit, and fix the harness to the clamp.
C. Install of the Connection fixture F/R
1)
Install the Connection fixture F (Packed items) to the main unit
with the fixing screws (Packed items).
with the fixing screws (Packed items).
2)
Install the Connection fixture R (Packed items) to the main unit
with the fixing screws (Packed items).
with the fixing screws (Packed items).
2
3
1
Click on the first or last page to see other MX-4140N / MX-4141N / MX-5140N / MX-5141N (serv.man8) service manuals if exist.