Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) Service Manual ▷ View online
MX-4070V Heater kit 5 – 25
2)
Attach LCC connecting plate left and put the harnesses through
the Edge saddle on Paper feed unit.
the Edge saddle on Paper feed unit.
(3)
Heater harness unit attachment
1)
Attach AC cord fixer and Heater harness as shown below and fix
the round terminal with a screw.
Connect the Heater harness connector and Heater connector.
the round terminal with a screw.
Connect the Heater harness connector and Heater connector.
(4)
Cabinet attachment
1)
Attach the LCC unlock connecting plate.
2)
Attach Left front cabinet and Left rear cabinet.
3)
Attach Rear cabinet.
Ĭ
ĭ
A
*CTPGUUGU
'FIGUCFFNG
2CRGTHGGFWPKV
ĭ
ĭ
ĭ
ĭ
ĭ
ĭ
ĭ
Ĭ
MX-4070V Heater kit 5 – 26
4)
Paste a protection sheet according to the cutout position on the
plate.
plate.
(5)
Connector connection
1)
Remove the connector cover.
Do not use the connector cover removed.
2)
Connect the connector.
If the dehumidifier heater kit is not installed, there is no need to
connect the dehumidifier heater connector to the connector.
connect the dehumidifier heater connector to the connector.
G. Operation check after installation
1)
Turn on the dehumidifier heater switch.
2)
Measure the resistance value between the earth terminal and the
AC terminal (L side), and between the earth terminal and AC ter-
minal (N side) with the circuit tester, and confirm they are not
short-circuited.
AC terminal (L side), and between the earth terminal and AC ter-
minal (N side) with the circuit tester, and confirm they are not
short-circuited.
3)
When not using the dehumidifier heater after checking, turn off the
dehumidifier heater switch.
dehumidifier heater switch.
Ĭ
ĭ
.%%JCTPGUUKUEQXGTGFYKVJCEQPPGEVQTEQXGT
The dehumidifier heater connector
MX-LC17 connector
Ĭ
ĭ
Ĭ
ĭ
MX-4070V MX-LC17 N (LARGE CAPACITY TRAY) 6 – 1
MX-4070V
Service Manual
[6] MX-LC17 N (LARGE CAPACITY TRAY)
1. Unpacking
If the connector is removed first, it may be damaged during the instal-
lation procedures. Therefore, keep it packed while un-boxing and
unpack it only when connecting the connector to the machine.
lation procedures. Therefore, keep it packed while un-boxing and
unpack it only when connecting the connector to the machine.
A. Packed items check
2. Installation
Before installation, be sure to turn both the operation and main power
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
A. Release the lock
1)
Remove the paper feed desk fixing screw.
NOTE: Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on without
removing the fixing screw, a trouble may be resulted.
removing the fixing screw, a trouble may be resulted.
No.
Name
Quantity
1
Large capacity tray
1
2
Mounting plate upper
2
3
Connecting unit
1
4
Fixing screw A (Hex washer S-tight M4x18)
4
5
Fixing screw B (Hex washer S-tight M4x12)
2
6
Fixing screw C (M4x8 cup)
1
7
LCC Guide sheet
1
2
1
3
4
6
5
7
MX-4070V MX-LC17 N (LARGE CAPACITY TRAY) 6 – 2
B. Main unit and large capacity tray unit connection
1)
Attach the mounting plate upper (Packed item No.2) to the right
side of main unit with the fixing screw A (Packed item No.4).
When installing, put the rubber section (
side of main unit with the fixing screw A (Packed item No.4).
When installing, put the rubber section (
) of the mounting plate
upper on the lower side.
2)
Remove the right door cover from the machine.
3)
Attach the LCC guide sheet (Packed item No.7) onto the paper
entering guide.
entering guide.
Clean surface of the LCC guide sheet with alcohol.
4)
Remove the fixing screws (1 pc) of the machine and remove the
screw cap. And remove the right under cover.
screw cap. And remove the right under cover.
Ĭ
ĭ
Ĭ
ĭ
Attachment position of LCC guide sheet.
Be sure no protruding the tip of the sheet
on the paper transportation guide.
Sectional view.
0mm
0.5mm
0mm
0.5mm
Ĭ
ĭ
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) service manuals if exist.