Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) Service Manual ▷ View online
MX-4070V Heater kit 5 – 21
4)
Pass the harness of the heater unit for the tray 3/4 through the
hole in the frame, and pass it through the clamp.
hole in the frame, and pass it through the clamp.
(7)
Heater harness 2 attachment
1)
Remove the desk LCC connector fixing plate.
2)
Attach the heater harness 2 to the desk LCC connector fixing
plate.
plate.
3)
Attach the desk LCC connector fixing plate.
4)
Attach the circle terminal of heater harness 2 with the two screws
(M4x8) and attach the heater frame 2 with the reusable band.
(M4x8) and attach the heater frame 2 with the reusable band.
Left side
Right side
Rear
Ĭ
Ĭ
ĭ
ĭ
Į
Į
Į
ĭ
ĭ
Ĭ
MX-4070V Heater kit 5 – 22
(8)
Heater harness attachment
1)
Attach the reusable band of the heater harness and connect the
connector of the heater harness to the connector of the heater
harness 2.
connector of the heater harness to the connector of the heater
harness 2.
2)
Attach the reusable band of the heater harness and connect the
connector of the heater harness to the connector of the tray 2
heater. Then, attach the circle terminal of heater harness with the
two screws (M4x8)
connector of the heater harness to the connector of the tray 2
heater. Then, attach the circle terminal of heater harness with the
two screws (M4x8)
3)
Attach the reusable band of the heater harness and connect the
connector of the heater harness to the connector of the tray 3/4
heater, and pass the heater harness through the clamp.
connector of the heater harness to the connector of the tray 3/4
heater, and pass the heater harness through the clamp.
(9)
Paper feed tray attachment
1)
Clean the label attaching surface of the tray 2 by the alcohol and
affix the high temperature warning label onto the frame.
affix the high temperature warning label onto the frame.
2)
Attach the paper feed tray.
(10) Right rear cabinet, rear cabinet and Connector cover
attachment
1)
Attach the right rear cabinet.
Ĭ
ĭ
Į
Ĭ
ĭ
Į
į
ĭ
Į
į
İ
ı
ı
Ĭ
0mm
0.5mm
0mm
0.5mm
ĭ
ĭ
Ĭ
MX-4070V Heater kit 5 – 23
2)
Attach the rear cabinet.
3)
Attach the Connector cover.
(11) Connector connection
1)
Remove the rear cabinet cover of the machine.
2)
Attach the edge saddle.
3)
Connect the heater harness to the machine harness.
The heater harness are held by the Edge saddle.
4)
Cut the part of the removed cover shown in the figure.
5)
Attach the rear cabinet cover of the machine.
ĭ
ĭ
ĭ
Ĭ
ĭ
Ĭ
Be careful of the mounting direction.
Open the right side.
Open the right side.
1 stage desk: No.12
2/3 stage desk: No.14
2/3 stage desk: No.14
Ĭ
ĭ
Į
MX-4070V Heater kit 5 – 24
F. LCC heater kit installation
(1)
cabinet removal
1)
Remove screws and remove Rear cabinet.
2)
Remove screws and remove Left front cabinet and Left rear cabi-
net.
net.
3)
Remove screws and remove LCC unlock connecting plate.
4)
Remove the harnesses on Paper feed unit from the Edge saddle.
Remove screws, slightly pull out the rear side of the LCC connect-
ing plate left toward front and slightly slide toward rear side.
Remove the harness avoiding the section A.
ing plate left toward front and slightly slide toward rear side.
Remove the harness avoiding the section A.
(2)
Heater attachment
1)
Attach Heater and M clamp. Put the harness through the M
clamp.
clamp.
Ĭ
Ĭ
Ĭ
Ĭ
Ĭ
Ĭ
Ĭ
ĭ
Ĭ
ĭ
A
*CTPGUUGU
'FIGUCFFNG
2CRGTHGGFWPKV
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) service manuals if exist.