Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) Service Manual ▷ View online
MX-4070V Heater kit 5 – 13
(2)
WH harness connection
1)
Connect the connector on AC PWB.
2)
Connect the connector on WH PWB.
3)
Attach the three clumps to the frame. And pass it through the
clamp.
clamp.
4)
Attach the earth wire.
The boss of the rotation stopper come to the right side of the ter-
minal.
minal.
(3)
Dehumidifier heater control switch attachment
1)
Connect the WH harness to the dehumidifier heater control
switch.(Connect to the terminal on the AC cord side.) And attach
the dehumidifier heater control switch.
switch.(Connect to the terminal on the AC cord side.) And attach
the dehumidifier heater control switch.
2)
Cut away the dehumidifier heater control switch section on the
rear cabinet.
Attach the dehumidifier heater control switch label to the rear cab-
inet.
rear cabinet.
Attach the dehumidifier heater control switch label to the rear cab-
inet.
Ĭ
ĭ
Į
į
į
Ĭ
ĭ
Į
DH
PO
WER
PO
WER
MX-4070V Heater kit 5 – 14
C. Heater kit installation
(1)
Heater unit assembly
1)
Attach the heater to the heater mounting plate and secure it with
the screw (M3 x 6 S-tight).
Attach the clamp, and fix the harness to the clamp.
the screw (M3 x 6 S-tight).
Attach the clamp, and fix the harness to the clamp.
The direction where the heater is attached to do the indication
side of voltage / electricity specifications listed in a heater in the
bottom.
side of voltage / electricity specifications listed in a heater in the
bottom.
2)
Attach the CSS-WH harness to the heater mounting plate, and
connect the harness of the dehumidifier heater.
connect the harness of the dehumidifier heater.
(2)
Heater unit attachment
1)
Remove the tray 1.
2)
Open the front cover. Attach the heater unit to the main unit, and
secure it with the screw (M4 x 10 P-tight).
secure it with the screw (M4 x 10 P-tight).
Pass the harness of the heater through the hole on the main unit
frame.
frame.
3)
Attach the wire saddle to the mein frame. Pass the CCS-WH har-
ness through the wire saddle. Connect the CCS-WH harness to
the AC-WH harness.
ness through the wire saddle. Connect the CCS-WH harness to
the AC-WH harness.
No.1
No.2
No.3
No.7
No.4
No.10
No.10
No.8
Ĭ
ĭ
No.5
ACWH harness
CSS-WH
harness
harness
MX-4070V Heater kit 5 – 15
4)
Attach the High temperature caution label to the casette 1. (Only
200V series.)
200V series.)
(3)
External fixture attachment
1)
Close the front cover.
2)
Install the casette 1 to main body.
3)
Attach the rear cabinet.
D. Scanner heater kit installation
(1)
Scanner heater unit assembly
1)
Secure the marking position on the harness of the scanner heater
to the heater fixing plate with the banding band.
to the heater fixing plate with the banding band.
2)
Extend the harness, and secure the other position of it with band-
ing band.
ing band.
No.9
ĭ
ĭ
Ĭ
ĭ
ĭ
ĭ
ĭ
3
᳸OO
2
1
MX-4070V Heater kit 5 – 16
3)
Tighten the snap band and cut its tip to approx. 5 mm or less.
Slide the banding band head to the square hole (Part that is
enclosed by the mark).
enclosed by the mark).
The banding band head and cut tip must not protrude behind the
heater fixing plate.
heater fixing plate.
(2)
Table glass removal
1)
Open the SPF.
2)
Remove the glass holder. Remove the table glass and the SPF
glass.
glass.
(3)
Scanner heater unit attachment
1)
Remove the two screws.
DSPF type only
Ĭ
ĭ
Į
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) service manuals if exist.