Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) Service Manual ▷ View online
MX-4070V Heater kit 5 – 17
2)
Attach the FFC cover.
3)
Attach the clamp to the scanner frame.
When installing, be careful to prevent damage of the wire.
4)
Connect the harness of the scanner heater. Attach the scanner
heater unit, and fixing the screw (M3 x 4 Round-tipped).
heater unit, and fixing the screw (M3 x 4 Round-tipped).
5)
Attach the scanner heater and secure it with the screw (M4 x 6
Bind machine screw). Pass the harness through the clamp.
Bind machine screw). Pass the harness through the clamp.
The convex part of the scanner heater must be inserted into the
hole of the scanner frame.
hole of the scanner frame.
6)
Tighten the loose scanner heater harness by pulling it in the arrow
direction and secure it with the snap band then cut its tip to
approx. 5 mm or less.
direction and secure it with the snap band then cut its tip to
approx. 5 mm or less.
7)
Move the lamp unit by hand and check that it move smoothly in all
movable area.
movable area.
Check that there is no interference of the harness of the scanner
heater in the wire and the 2/3 mirror unit.
heater in the wire and the 2/3 mirror unit.
Use the attached screw.
Use the removed screw.
2
2
1
1
2
MX-4070V Heater kit 5 – 18
(4)
Table glass attachment
1)
Attach the SPF glass and the table glass. Attach the glass holder.
When installing the glass holder, slide it to the left until it clicks,
and fix it with screws.
and fix it with screws.
2)
Close the SPF.
E. Desk heater kit installation
(1)
Tray 2 heater unit assembly
1)
Clean the label attaching surface of the desk heater mount plate
upper by the alcohol and attach the desk heater protection sheet.
upper by the alcohol and attach the desk heater protection sheet.
2)
Attach the desk heater to the heater mounting plate, and fix it with
a screw (M3 x 4 S tight bind).
a screw (M3 x 4 S tight bind).
3)
Attach the mini clamp on the desk heater mount plate upper and
pass the heater harness through it.
pass the heater harness through it.
DSPF type only
Ĭ
ĭ
Į
±1mm
±1mm
Ĭ
Ĭ
ĭ
ĭ
Ĭ
MX-4070V Heater kit 5 – 19
(2)
Tray 3/4 heater unit assembly
1)
Attach the desk heater to the heater mounting plate, and fix it with
a screw (M3 x 4 S tight bind).
a screw (M3 x 4 S tight bind).
(3)
Connector cover, rear cabinet and right rear cabinet
removal
removal
1)
Remove the Connector cover.
2)
Remove the rear cabinet.
3)
Remove the right rear cabinet.
(4)
Paper feed tray removal
1)
Pull out the paper feed tray, and lift it to remove.
(5)
Tray 2 heater unit attachment
1)
Pass the harness of the heater unit for the tray 2 through the hole
in the frame. Attach the heater unit for the tray 2 to the frame, and
fix it with a screw (M3 x 6 S tight bind).
in the frame. Attach the heater unit for the tray 2 to the frame, and
fix it with a screw (M3 x 6 S tight bind).
Ĭ
ĭ
ĭ
Ĭ
ĭ
Ĭ
Ĭ
Ĭ
ĭ
Ĭ
Ĭ
ĭ
Ĭ
ĭ
MX-4070V Heater kit 5 – 20
2)
Attach the mini clamp on the rear frame.
3)
Pass the heater harness through the mini clamp.
4)
Clean the label attaching surface of the desk bottom by the alco-
hol and affix the high temperature warning label onto the frame.
hol and affix the high temperature warning label onto the frame.
(6)
Tray 3/4 heater unit attachment
1)
Attach the four mini clamps on the desk bottom.
2)
Attach the two mini clamps on the rear frame.
3)
Attach the heater unit for the tray 3/4 to the frame, and fix it with a
screw (M3 x 6 S tight bind).
screw (M3 x 6 S tight bind).
0mm
0mm
0.5mm
0.5mm
Ĭ
Ĭ
ĭ
ĭ
ĭ
ĭ
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man7) service manuals if exist.