DOWNLOAD Sharp AR-M165-207 (serv.man17) Service Manual ↓ Size: 13.1 MB | Pages: 127 in PDF or view online for FREE

AR-M207 M165 M162 SIMULATIONS 7-18

24

13

Used to clear the scanner counter.

[OK] or [START] key: Clears the scanner counter and shifts to the sub code input window. 
[CA] key: Exits the simulation mode.
[Interruption] key: Shifts to the sub code input window. 

14

Used to clear the SPF jam total counter.

[OK] or [START] key: Clears the SPF jam total counter and shifts to the sub code input window.
[CA] key: Exits the simulation mode.
[Interruption] key: Shifts to the sub code input window.

15

Used to clear the scanner mode counter.

[OK] or [START] key: Clears the scanner mode counter and shifts to the sub code input window.
[CA] key: Exits the simulation mode.
[Interruption] key: Shifts to the sub code input window. 

25

01

When [OK] key or [START] key is pressed, the main motor (as well as the duplex motor in the case of the 
duplex model) is rotated for 30 sec.
If the developing unit is installed to save toner consumption at that time, the developing bias, the main 
charger, and the grid are also outputted.
In addition, since laser discharge is required when the motor is stopped, the polygon motor is also operated. 
Check if the developing unit is installed or not. If it is not installed, the previous high voltage is not outputted 
and only the motor is rotated.
After completion of 30sec operation, the machine shifts to the sub code input window.
* This simulation must not be executed with the door open/close switch forcibly turned ON.

After completion of the process, the machine shifts to the sub code input window. 
[CA] key: Exits the simulation mode.
[Interruption] key: Interrupts the output operation, and shifts to the sub code input window. 

Main 
code

Sub 

code

Contents

Remark

Sim24-13 COUNTER CLR

AER YOU SURE? EXEC

SCAN COUNTER 
CLEAR

Sim24-14 COUNTER CLR

AER YOU SURE? EXEC

SPF JAM COUNTER 
CLEAR

Sim24-15 COUNTER CLR

AER YOU SURE? EXEC

SCANNER MODE
COUNTER CLEAR

Sim25-1  MAIN MOTOR

PRESS OK KEY

EXEC

Sim25-1  MAIN MOTOR

EXEC

OK/START Key

(Execution start window)

(Execution window)

[07]SIMULATIONS.fm  18 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分

AR-M207 M165 M162 SIMULATIONS 7-19

25

10

When [OK] or [START] is pressed, the polygon motor is rotated for 30sec.

After completion of the process, the machine shifts to the sub code input window.
[CA] key: Exits the simulation mode.
[Interruption] key: Interrupts the output operation, and shifts to the sub code input window. 

26

01

Used to set YES/NO of installation of the hob separator.
After installation of the job separator, setting must be manually set to YES. 

[CA] key: Exits the simulation mode. (When setting is changed, the machine exits the simulation mode and 
performs the hard reset.)
[Interruption] key: Shifts to the sub code input window. (When setting is changed, it is invalid.)
[START] key:  Setting contents are saved in the EEPROM and the machine shifts to the code input window.   

(When setting is changed, the machine does not shift to the code input window.)

02

Used to set Enable/Disable of FC (8.5" x 13") size detection.
Detection size when FC (8.5" x 13") size document is used.

* For destinations other than the above, this setting is invalid.

Default:
00

03

Used to set the auditor.

* When the coin vendor mode is selected:

1. Sort auto select is OFF.
2. For Japan, the duplex copy use inhibition setting is ON (inhibited).

3. When the auditor mode exclusive-setting is ON (manual paper feed inhibited) and the standard tray is set

to the manual feed tray, the standard tray setting is set to the main tray. 

Default:
0 (P10)

Main 
code

Sub 

code

Contents

Remark

Sim25-10 LSU CHECK

PRESS OK KEY

EXEC

Sim25-10 LSU CHECK

EXEC

OK/START Key

(Execution start window)

(Execution window)

Sim26-1 JBS SET

1:JOB SEPARATOR
 0=NONE
 1=SEPARATOR
                 [   0-1]

0 : No job separator
1 : Job separator provided 

0

0

Unit to be 

used

Destination

Document size

Set value

0(Disable)

1(Enable)

Document

SPF

EX Japan AB 
series(FC)

FC(8.5"x13")

B4

FC(8.5"x13")

B4

B4

FC(8.5"x13")

Inch 
series(FC)

FC(8.5"x13")

LG(8.5"x14")

FC(8.5"x13")

LG(8.5"x14")

LG(8.5"x14")

FC(8.5"x13")

Sim26-2 SIZE SET

1:B4/LG,FC
 0=B4/LG
 1=FC
                 [   0-1]

Code: Setting
0 : Detection disabled
     (Default for destinations other than below)
1 : FC detection enabled
     (Default for SCA/Philippines)

0

0

Sim26-3 AUDITOR SET

1:AUDITOR
 0=P10

1=VENDOR

 2=OTHER
                 [   0-2]

Code: Mode
0 : Built-in auditor mode
1 : Coin vendor
2 : Other

0

0

[07]SIMULATIONS.fm  19 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分

AR-M207 M165 M162 SIMULATIONS 7-20

26

04

Used to set YES/NO of duplex setting.
This must be set to ON when the duplex unit is installed. If this setting is set to OFF on the duplex machine, 
the duplex motor dose not rotate and paper is not discharged normally, resulting in a paper jam.

05

Used to set the count-up number of the total counter, the developer counter, and the maintenance counter 
individually when a special paper (A3/WLT/8K) is passed.
When this simulation is executed, the current set value is displayed.

[1]-[3] (Default:[0])
Enter a value with 10-key, and press [OK] key or [START] key to save the current adjustment value to the 
EEPROM. The machine returns to the sub code input window. 

Default:
0 (+2)

06

Used to set the destination of the main unit.
When this simulation is executed, the code number of currently set destination is displayed.

[0] - [6] (Default: Depends on the model.)
Enter a value with 10-key, and press [OK] key or [START] key, and the current adjustment value is saved in 
the EEPROM.
[CA] key: Exits the simulation mode. (When setting is changed, the machine exits the simulation mode and 

performs the hard reset.)

[Interruption] key: Shifts to the sub code input window. (When setting is changed, it is invalid.)
[START] key: Setting contents are saved in the EEPROM and the machine shifts to the code input window. 

(When setting is changed, the machine does not shift to the code input window.)

* When this setting is changed, the following adjustment values and the set values are automatically

changed according to the set destination.

O SIM46-19 (

 table setting)

O SIM46-30 (AE limit setting)
O Paper size (A4 for AB series, LT for inch series)
O Maintenance cycle (Returns to the default (Japan/Ex Japan). )
O Mini maintenance cycle (Only when setting is changed to Japan.) 

Default:
1

Main 
code

Sub 

code

Contents

Remark

Sim26-4 DUPLEX SET

1:DUPLEX
 0=OFF

1=ON 

                
                  [   0-1]

Code: Duplex setting
0 : OFF
1 : ON

0

0

Sim26-5 COUNT MODE

1:COUNT MODE
  
                
                  [   0-3]

1

1

Setting

Total/Developer

Maintenance

0

+2

+2

1

+1

+2

2

+2

+1

3

+1

+1

Sim26-6 DESTINATION

1:DESTINATION
 0=JAPAN 
                
                  [   0-6]

Code

:Setting

0=JAPAN

: Japan AB series

1=INCH

: Inch series

2=AB

: Ex Japan AB series

3=INCH(FC)

: Ex Japan inch series (FC)

4=AB(FC)

: Ex Japan AB series (FC)

5=CHINESE

: China (EX Japan AB series + Chinese paper support)

6=TAIPEI

: Taiwan (EX Japan AB series + Chinese paper support)

(Setting range 0 - 6)

0

0

[07]SIMULATIONS.fm  20 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分

AR-M207 M165 M162 SIMULATIONS 7-21

26

07

When this simulation is executed, the copy speed of the machine is displayed.

[CA] key: Exits the simulation mode.
[Interruption] key: Shifts to the sub code input window. 

18

Used to switch ON/OFF of the toner save mode.
When this simulation is executed, the current set value is displayed. Enter a set value with 10-key and press 
[OK] key or [START] key. The set value is saved in the EEPROM.
* When this setting is changed, the toner save setting of the key operator program is also changed

accordingly.

[CA] key: Exits the simulation mode.
[Interruption] key: Shifts to the sub code input window. 

Default:
0 (Toner save OFF)

20

Used to set the paper exit mode of the job separator.
* The purpose is to allow the simplified check when the job separator option is installed. It is valid only

during the adjustment simulation. Without installing a printer or a FAX machine, paper is discharged to the

upper stage to check if there is no problem or not.

If SIM26-01 is set to "Job separator not installed," paper is discharged to the lower stage regardless of
this setting.

[CA] key: Exits the simulation mode.
[Interruption] key: Shifts to the sub code input window. 

Default:
0 (OFF)

22

Used to clear the language setting. The scanner head is shifted to the fixing lock position.
(1) Initial display

(2) Press [OK]or [START] key.(Execution is starred.)

(3) After completion of counter clear and shifting to the lock position

Main 
code

Sub 

code

Contents

Remark

Sim26-7 CPM CHECK

16CPM

Displayed CPM list
14CPM
16CPM
20CPM

Sim26-18 TONER SAVE

1:TONER SV MODE
 0=OFF     1=ON 
                
                  [   0-1]

Code: Setting
0: Toner save OFF
1: Toner save ON

0

0

Sim26-20 JOBSEP OUT

1:JOBSEP OUT
 0=OFF

1=ON 

                
                  [   0-1]

Code: Setting
0: Lower tray
1: Upper tray

0

0

Sim26-22 LANGUAGE

AER YOU SURE? EXEC

LANGUAGE SETTING 
CLEAR

Sim26-22 LANGUAGE

LANGUAGE SETTING 
CLEAR

EXEC

Sim26-22 LANGUAGE

PLEASE SHUT OFF 
THE POWER.

[07]SIMULATIONS.fm  21 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分