DOWNLOAD Sharp AR-M165-207 (serv.man17) Service Manual ↓ Size: 13.1 MB | Pages: 127 in PDF or view online for FREE

AR-M207 M165 M162 SIMULATIONS 7-2

<Execution inhibit conditions>

*1) Execution is inhibited when the duplex setup is OFF and other than

RSPF is set. 

*2) Execution is inhibited when OC.

*3) Execution is inhibited when SPF. (Not RSPF)
*4) Execution is inhibited when the job separator is not installed.

*5) Execution is inhibited when the model is not provided with the

CRUM. 

*6) Execution is inhibited when the duplex setup is OFF. 

25

01

Main motor operation check (Cooling fan motor rotation 
check)

10

Polygon motor operation check 

26

01

Job separator setting

02

Size setting

03

Auditor setting

04

Copier duplex setting

05

Count mode setting

06

Destination setting

07

Machine condition check

18

Toner save mode setting

20

Job separator paper exit mode setting

22

Language setting clear

30

CE mark conformity control ON/OFF

31

Auditor mode exclusive setup

36

Cancel of stop at maintenance life over

37

Cancel of stop at developer life over

39

Memory capacity check

42

Transfer ON/OFF timing control setting

43

Side void amount setting

51

Copy temporary stop function setting

54

LCD contrast PWM duty setting

60

FAX mode key Enable/Disable setting

73

Toner save setting display/non-display

74

Total counter display change setting

30

01

Paper sensor status display

41

01

Document size detection photo sensor check

02

Document size detection photo sensor detection level 
adjustment

03

Document size detection photo sensor light receiving/
detection level check

04

Detection level adjustment when the document size is 
settled(15degrees - 20degrees)

42

01

Developing counter clear

43

01

Fusing temperature setting (Normal copy)

12

Standby mode fusing fan rotation setting

13

Fusing paper interval control allow/inhibit setting

44

34

Transfer current setting

40

Setting of rotation time before toner supply

46

01

Copy density adjustment (300dpi)

02

Copy density adjustment (600dpi)

09

Copy exposure level adjustment, individual setting 
(Text) 300dpi

10

Copy exposure level adjustment, individual setting 
(Text) 600dpi

11

Copy exposure level adjustment, individual setting 
(Photo) 600dpi

18

Image contrast adjustment (300dpi)

19

Exposure mode setting
(Gamma table setting/AE operation mode setting/
Photo image process setting)

20

SPF exposure correction *2

29

Image contrast adjustment (600dpi)

30

AE limit setting

31

Image sharpness adjustment

48

01

Main/sub scanning magnification ratio adjustment

05

SPF/RSPF mode sub scanning magnification ratio 
adjustment in copying *2

49

01

Flash ROM program writing mode

Main 
code

Sub 

code

Contents

50

01

Image lead edge adjustment

06

Copy lead edge position adjustment (SPF/RSPF) *2

10

Paper off-center adjustment

12

Document off-center adjustment 

18

Memory reverse position adjustment in duplex copy *1

19

Rear edge void adjustment in duplex copy *6

51

02

Resist amount adjustment

53

08

SPF scanning position automatic adjustment *2

10

SPF scanning position setting

61

03

HSYNC output check 

63

01

Shading check

07

SPF automatic correction *2

64

01

Self print

65

10

Key reception time setting display/non-display setting

11

Info lamp setting

67

50

USB reception speed adjustment

Main 
code

Sub 

code

Contents

[07]SIMULATIONS.fm  2 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分

AR-M207 M165 M162 SIMULATIONS 7-3

Main 
code

Sub 

code

Contents

Remark

01

01

Used to check the operations of the scanner unit and its control circuit. 
Enter the number of times and the magnification ratio, and press [OK] key to operate the scanner unit. The 
speed is variable according to the specified magnification ratio. The number of scanning can be specified by 
entering a value to the right lower section of the LCD.
•Setting range of magnification ratio: 25%-400%

•Setting range of the number of scanning: 0-999 (When 0 is set, it means unlimited. )

Used to display the status (ON/OFF) of the mirror HP sensor on the LCD during scanning. (Highlighted at 
ON)
"EXEC" is displayed to indicate execution is in process. The scan counter is displayed above "EXEC." This 
counter is counted up even in simulation.
 The copy lamp is lighted during scanning.

[CA] key: Exits the simulation mode.
[Interruption] key: Returns to the sub code input window.
[C] key: Input value clear
10 key: Input of the number of scanning

02

Used to monitor the mirror home position sensor and display the ON/OF status of the sensor on the LCD.

[CA] key: Exits the simulation mode.
[Interruption] key: Returns to the sub code input window.

Sim1-1 SCAN CHECK

MHPS

OK/START Key

MHPS sensor status

Scan counter

(Scan number input window)

(Execution
         window)

Highlighted during execution

ZOOM

100%

5

123

Sim1-1 SCAN CHECK

ZOOM

100%

EXEC

123

MHPS

Set the scan magnification ration.
This magnification ratio accords with the scan speed
in actual copying. The setting range is 25% - 400%. 

Specify the scan number to be performed. 
The setting range is 0 - 999. When 0 is set,
the number is unlimited.

115%

100%

  86%

115%

100%

  86%

Sim1-2 SENSOR CHECK

MHPS

MHPS(MIRROR HOME POSITION SENSOR)
ON

:Highlight display

OFF

:Normal display

[07]SIMULATIONS.fm  3 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分

AR-M207 M165 M162 SIMULATIONS 7-4

02

01

Used to check the operations of the SPF unit and its control circuit.
Enter the magnification ratio and press OK or [START] key to drive the SPF unit at the speed corresponding 
to the setting.

* When [Interruption] key is press, the simulation is terminated and the machine returns to the sub code

input window. 

* When [CA] key is pressed, the simulation is terminated and the machine exits the simulation mode. 

02

Used to display the sensor status in the SPF/RSPF section. An active sensor is highlighted.

[CA] key: Exits the simulation mode.
[Interruption] key: Returns to the sub code input window.

03

Used to check the operation of the SPF motor and its control circuit. When this simulation is executed, the 
initial menu shown below is displayed. Select the magnification ratio to drive the motor.

[CA] key: The SPF motor is stopped, and the machine exits the simulation mode. [Interruption] key: The SPF 
motor is stopped, and the machine returns to the sub code input window.

Main 
code

Sub 

code

Contents

Remark

Sim2-1 SPF AGING

115%

100%

  86%

1SIDE

2SIDE

OK/START Key

(Magnification ratio selection window)

ZOOM

100%

EXEC

Sim2-1 SPF AGING

115%

100%

  86%

1SIDE

2SIDE

(Execution
         window)

ZOOM

100%

EXEC

Select the scan magnification ratio (drive speed).
This also accords with the magnification ratio and
the speed in copying similarly to the OC.
The setting range is 50% - 200%.

"EXEC" is highlighted during execution.

Sim2-2 SENSOR CHECK

SPFP
OCCV
POUT
SPFC

L1
L2

W0

W1

W2
W3

Displayed name

: Sensor name

SPFP

:SPF document transportation sensor

OCCV

:SPF unit (OC cover) open/close sensor

POUT

:SPF paper exit sensor

SPFC

:SPF paper feed cover open/close sensor

L1

:SPF paper length sensor 1

L2

:SPF paper length sensor 2

W0

:SPF document set sensor

W1

:SPF paper width sensor (small) 

W2

:SPF paper width sensor (middle)

W3

:SPF paper width sensor (large)

Sim2-3 OUTPUT CHECK

Sim2-3 OUTPUT CHECK

115%

100%

  86%

OK/START Key

(Initial window = Magnification ratio selection window)

ZOOM

100%

EXEC

115%

100%

  86%

ZOOM

100%

EXEC

(Execution
         window)

Select the scan magnification ratio (drive speed).
This also accords with the magnification ratio and
the speed in copying.
The setting range is 50% - 200%.

"EXEC" is highlighted during execution.

[07]SIMULATIONS.fm  4 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分

AR-M207 M165 M162 SIMULATIONS 7-5

02

08

Used to drive the SPF paper feed solenoid (PSOL) 20 times in the cycle of 500msec of "ON" and 500msec 
of "OFF." After completion of the process, the machine returns to the sub code input window.

When [Interruption] key is pressed, the machine returns to the sub code input window.
When [CA] key is pressed, the machine exits the simulation mode. 

09

Used to drive the SPF reverse solenoid (RSOL) 20 times in the cycle of 500msec of "ON" and 500msec of 
"OFF." After completion of the process, the machine returns to the sub code input window.

When [Interruption] key is pressed, the machine returns to the sub code input window.
When [CA] key is pressed, the machine exits the simulation mode.

10

Used to drive the SPF paper exit gate solenoid (GSOL) 20 times in the cycle of 500msec of "ON" and 
500msec of "OFF." After completion of the process, the machine returns to the sub code input window.

When [Interruption] key is pressed, the machine returns to the sub code input window.
When [CA] key is pressed, the machine exits the simulation mode.

11

Used to drive the SPF PS release solenoid (CLH) 20 times in the cycle of 500msec of "ON" and 500msec of 
"OFF." After completion of the process, the machine returns to the sub code input window.

When [Interruption] key is pressed, the machine returns to the sub code input window.
When [CA] key is pressed, the machine exits the simulation mode.

03

02

Used to monitor the sensors related to the shifter and the job separator and display the sensor status on the 
LCD. An active sensor is highlighted.

* Displayed only when the job separator is installed except for SFTH.

Main 
code

Sub 

code

Contents

Remark

Sim2-8  SPUS CHECK

PRESS OK KEY

EXEC

Sim2-8  SPUS CHECK

EXEC

OK/START Key

(Initial window)

(Execution window)

Sim2-9  SPFS CHECK

PRESS OK KEY

EXEC

Sim2-9  SPFS CHECK

EXEC

OK/START Key

(Initial window)

(Execution window)

Sim2-10  SGS CHECK

PRESS OK KEY

EXEC

Sim2-10  SGS CHECK

EXEC

OK/START Key

(Initial window)

(Execution window)

Sim2-11  CLH CHECK

PRESS OK KEY

EXEC

Sim2-11  CLH CHECK

EXEC

OK/START Key

(Initial window)

(Execution window)

Sim3-2 SENSOR

SFTHP
TRYF

JSUP

TRYD

JSDL

Displayed name

:Sensor name

SFTHP

:Shifter home position sensor

JSUP

:Job separator upper limit sensor

JSDL

:Job separator lower limit sensor

TRYF

:Tray full sensor

TRYD

: Paper exit sensor

[07]SIMULATIONS.fm  5 ページ  ２００４年１１月１７日　水曜日　午後１２時１１分