DOWNLOAD Sharp AR-EB7 (serv.man2) Service Manual ↓ Size: 118.21 KB | Pages: 2 in PDF or view online for FREE

Model
AR-EB7 (serv.man2)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
118.21 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Unpacking installation
File
ar-eb7-sm2.pdf
Date

Sharp AR-EB7 (serv.man2) Service Manual ▷ View online

AR-EB7
UNPACKING AND INSTALLATION
– 4 –
[3] UNPACKING AND INSTALLATION
1. Unpacking
<Before installation>
For improvement of workability, any part of the description in this
manual may be modified without prior notice. In this case, refer to
the service manual.
2. Parts included
3. Installation procedure
Turn the main switch of the copier to the "OFF" position and then
remove the power plug of the copier from the power supply outlet.
1) Remove the rear cover.
Remove the screw, push the portion indicated by the arrow to
unlock the rear cover, and slide the cover to the right to remove it.
2) Cut out the cut-out portion of the rear cover.
Cut out the cut-out portion with nippers or the like.
At this time, be careful about the orientation of the nippers so that
the cut plane of the rear cover is flat.
3) Attach the IMC2 PWB.
Fit the two pawls on the rear surface of the IMC2 PWB frame to the
mounting portions of the copier and secure the PWB with the four
supplied golden screws M3 x 6.
IMC2 PWB (with frame)
screw (golden) M3 x 6: 4pcs.
Installation manual: 1 volume
Pawl for 
locking
Rear cover
Screw
Cut-out portion
Rear cover
Pawl
Screws (golden)
M3 x 6
Pawl
IMC2 PWB
Screws (golden)
M3 x 6
Take care not to get 
the cable caught.
AR-EB7
UNPACKING AND INSTALLATION
– 5 –
4) Connect the IMC2 PWB to the MCU PWB of the copier.
Connect the flat cables of the IMC2 PWB to the connectors of the
MCU PWB of the copier so that the shorter cable comes inside and
the longer cable comes outside as shown in the illustration.
Be careful about the orientation of the flat cable insertion and check
that both ends of each cable are securely inserted into the connec-
tor. (The terminal surface of each flat cable must have contact with
the connector terminals.)
5) Attach the rear cover.
Fit the four pawls of the rear cover to the rear cabinet, slide the
cover to the left until it is locked, and then secure the cover with the
screw.
Insert the power plug of the copier into the power supply outlet
and turn on the power switch. Then, carry out the following proce-
dure.
6) Check the IMC2 PWB.
Press the SORT/GROUP key on the operation panel to check that
the SORT mode indicator lights up.
7) Check printing.
For installation of the driver software on the computer, see the oper-
ation manual supplied with the copier.
Connect the USB cable, carry out printing from the computer, and
check that printing can be performed normally.
4.  Installation of additional memory 
(After installation, proceed to step 5.)
1
Open the two locking clips of the socket.
2
Insert the memory matching the orientation of its notches.
3
Close the locking clips of the socket.
Flat cable (shorter)
Flat cable (longer)
Copier MCU PWB
IMC2 PWB
Connector
Pawl
Pawl
Pawl
Pawl
Pawl for 
locking
Rear cabinet
Rear cover
Screw
1
1
2
3
3
As additional memory, use AR-SM5 (sold separately).
Display

Sharp AR-EB7 (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sharp AR-EB7 (serv.man2) Service Manual ↓ Size: 118.21 KB | Pages: 2 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp AR-EB7 (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp AR-EB7 (serv.man2) Copying Equipment. Information contained in Sharp AR-EB7 (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.