Sharp AR-651 (serv.man25) User Manual / Operation Manual ▷ View online
1
2
3
4
5
6
7
8
9
10
11
12
2-5
Pay attention to the following points:
- Avoid using paper that is specially treated or paper that was printed on another machine, and also
- Avoid using paper that is specially treated or paper that was printed on another machine, and also
avoid performing double copying on the same side of paper; this may cause a malfunction.
- Do not use paper with creases, wrinkles, curled paper, paper prone to curling, smooth paper, or tough
paper; this may cause paper misfeeds.
- Paper should be wrapped in its wrapping paper and stored in a damp-free place.
- To prevent paper from being folded or bent, store it evenly on a flat surface.
paper; this may cause paper misfeeds.
- Paper should be wrapped in its wrapping paper and stored in a damp-free place.
- To prevent paper from being folded or bent, store it evenly on a flat surface.
Handling and Storing Paper
1
2
3
4
5
6
7
8
9
10
11
12
2-6
HOW TO MAKE COPIES
2. SETTING COPY PAPER (Cont.)
The paper size of the drawers of the copier can be changed to desired size. The drawers can also be set for
cover sheet, insertion, tab paper, thick paper and special sheets.
cover sheet, insertion, tab paper, thick paper and special sheets.
1
Pull out the drawer toward you.
-Do not touch the slide rail of the drawer.
4
While pushing the size selection lever in the direction
of the arrow, set the side guide to the desired paper
width.
- Adjust the side guides with both hands.
3
Push the arrow part (right side) of the size selection
lever to unlock it.
5
Push the arrow part (left side) to lock the size selection
lever.
6
Place paper in the drawer(s).
- Place the paper in face down.
- Notes for placing paper in the drawer.
Page 7-3, step 2
7
Push the drawer straight into the copier until it
comes to a stop.
- Be sure to push the drawer carefully and fully in.
Be carefull not to let your fingers be caught when closing the drawer.
Changing the Paper Size of the Drawer/Setting the Drawer for Special Uses
Changing the Paper Size of the Drawer
2
Push the lower part of the width guide in the direction
of the arrow to remove it, and reinstall the width
guide at the desired paper size (indicated on the
bottom surface of the drawer).
Slide rail
1
2
3
4
5
6
7
8
9
10
11
12
2-7
8
Press the JOB STATUS key on the control panel,
then the CASSETTE key on the touch panel.
9
Press the drawer key corresponding to that in which
the paper size has been changed, then press the
key of the paper size newly set.
- Chinese paper sizes (16K, 8K and 16K-R) can be selected
on the screen which appears when the Next key is pressed
once. Pressing the Next key again will display the LT format
paper sizes.
once. Pressing the Next key again will display the LT format
paper sizes.
- Press the RETURN key on the touch panel or the JOB
STATUS key on the control panel to return to the basic screen.
You can set the drawer for various uses (cover sheet, sheet insertion and tab paper, thick paper special
sheets).The default paper is plain paper
Page 2-4
Drawer for cover sheet
Page 4-18
Drawer for sheet insertion
Page 4-20
Drawer for tab paper (must be used in second drawer)
Page 4-22
Drawer for special sheets...Coloured paper, paper with a watermark, etc.
1
Place paper in the drawer(s).
- Place the paper with its face down.
- Setting tab paper
Page 4-22
- For changing the paper size in the drawer, follow step 1 to 9
on the previous page.
2
Press the JOB STATUS key on the control panel,
then the CASSETTE key on the touch panel. After
this procedure, press the MADIA TYPE key.
Setting the Drawer for Special Uses
1
2
3
4
5
6
7
8
9
10
11
12
2-8
HOW TO MAKE COPIES
Press THICK 1 or THICK 2 depending on the paper weight of
cover sheet, insertion, and special sheet. In this case of cover
sheet and insertion, ’
cover sheet, insertion, and special sheet. In this case of cover
sheet and insertion, ’
’ or ‘
’ is displayed in the drawer key.
* For example, when inserting 163
g
/m
2
paper, press INSERT
key, and press THICK 1 key.
3
Press the drawer key corresponding to that in which
the paper has been set, then press the key of the
paper type newly set.
- If you want to select the COVER , INSERT , or TAB , make sure
that paper with the same size as that for the COVER, INSERT, or
TAB PAPER is set in the other drawer including the optional
external LCF (Large Capacity Feeder).
TAB PAPER is set in the other drawer including the optional
external LCF (Large Capacity Feeder).
- The setting is completed as shown on the right.
2. SETTING COPY PAPER (Cont.)
Changing the Paper Size of the Drawer/Setting the Drawer for Special Uses(Cont.)
Up to 2 drawers can be set for the sheet insertion.
After having set INSERT 1, press the drawer key corresponding
to that in which the paper for INSERT 2 has been set, and press
the INSERT key.
the INSERT key.
Clearing the Drawer for Special Uses
Press the drawer key corresponding to that which is
set for the special use, then press the key of the same
mode as the drawer.
- If you clear INSERT 1 when both INSERT 1 and INSERT 2 are
set, the drawer for INSERT 2 changes to INSERT 1.
- Replace the paper set in the drawer as required.
- Press the RETURN key on the touch panel or the
JOB STATUS key or either lighting one of
COPY key
or PRINTER/NETWORK key on the control panel to return to
the machine to the basic screen (before JOB STATUS key is
pressed on the step 2).
the machine to the basic screen (before JOB STATUS key is
pressed on the step 2).
Click on the first or last page to see other AR-651 (serv.man25) service manuals if exist.