Sharp AR-651 (serv.man25) User Manual / Operation Manual ▷ View online
1
2
3
4
5
6
7
8
9
10
11
12
2-1
2. HOW TO MAKE COPIES
1. General copying procedures .....................................................
2-2
2. Setting copy paper.....................................................................
2-4
- Acceptable copy paper types and sizes ..................................................... 2-4
- Handling and sorting paper ......................................................................... 2-5
- Changing the paper size of the drawer / Setting the drawer for special uses ............... 2-6
3. Setting originals .........................................................................
2-9
- Acceptable original types and sizes ........................................................... 2-9
- When placing an original on the glass ...................................................... 2-10
- When using the reversing automatic document feeder ............................. 2-11
4. Auto job start (Job preset) ........................................................
2-13
5. Interrupt copying .......................................................................
2-14
6. Stopping the copy operation .....................................................
2-15
7. Deleting or changing order of pending jobs ..............................
2-16
1
2
3
4
5
6
7
8
9
10
11
12
2-2
HOW TO MAKE COPIES
The initial (default) settings of the copier at the time of installation are as shown below.
*1 The copy modes that are automatically set when the power is turned on, when the energy-saving mode is
*1 The copy modes that are automatically set when the power is turned on, when the energy-saving mode is
cleared or when the CLEAR ALL key is pressed on the control panel are called the initial (default) settings.
Initial (default) settings
3
Select the copy modes
(
in the illustration on the page on the right)
.
- Use the touch panel and the digital keys.
4
Press the START key
(
in the illustration on the page on the right)
.
- When the reversing automatic document feeder is used and
the continuous feed mode is selected (
Page 5-2), copying begins.
1. GENERAL COPYING PROCEDURES
After placing, or confirming that there is, paper in the drawers, place the originals. When the START key
is pressed with any settings unchanged, copies are made in the initial (default) settings *
is pressed with any settings unchanged, copies are made in the initial (default) settings *
1
. You can make
copies as desired by setting different copy modes.
2
Place the original(s).
- Acceptable originals
Page 2-9
-When placing an original on the glass
Page 2-10
- When using the reversing automatic document feeder
Page 2-11
1
Place paper in the drawer(s).
-Acceptable copy paper
Page 2-4
5
Place the next original (2nd side) and press the
START key.
- Set the first page of your originals first.
- You can also press the YES key before pressing the
START key to perform the same operation.
- Repeat this step for the subsequent originals.
Reproduction ratio. ...100%
Copy quantity ......1
Automatic paper selection
1-sided copies from 1-sided originals
Auto image density
Standard mode (original image type)
Non-sort Non-staple mode
Continuous original feed mode
Copying Procedure
When the desired paper is not placed in any of the drawers or the large capacity feeder :
- Setting the drawer
Page 2-6
- Bypass copying
Page 5-8
- Selecting multiple copy modes may be restricted depending on their combination.
- Copy modes cannot be changed after the
- Copy modes cannot be changed after the
START key is pressed (including the case
when originals are divided into multiple sets when fed).
1
2
3
4
5
6
7
8
9
10
11
12
2-3
- After starting copying, press the JOB STATUS key on the control panel, then press the
STATUS key on the touch panel to indicate which drawer is in use. When paper runs out of
each drawer, the empty drawer will flash.
each drawer, the empty drawer will flash.
To make multiple sets of copies:
- Key in the copy quantity .
- To correct the input copy quantity, press the CLEAR key.
- To correct the input copy quantity, press the CLEAR key.
When the paper has run out in the middine of copying:
JOB STATUS key flashes. Press this key to check which drawer
is flashing and add papers.
is flashing and add papers.
To stop a copy operation
Page 2-15
When this message appears “Wait”:
The copier may automatically go into the adjustment mode. It
will soon start working. Do not turn OFF the power. Just wait
for a while.
will soon start working. Do not turn OFF the power. Just wait
for a while.
6
Once the final original has been scanned, press the FINISHED key.
- When the reversing automatic document feeder is used, and the single-feed mode is selected, the
procedure is slightly different from the above. Procedure of using the single-feed mode
Page 5-3
When Coming Across the Situations below
The paper exits with its printed side down except in the following
cases.
cases.
When paper is exited with its printed side up:
- When ‘Non-sort / Non-staple’ mode is selected for setting the
original on the original glass.
- When the paper size is not set for bypass copying.
original on the original glass.
- When the paper size is not set for bypass copying.
Exiting Copy Papers
1
2
3
4
5
6
7
8
9
10
11
12
2-4
HOW TO MAKE COPIES
*1 Automatic duplex copying is not available.
*2 Available only when non-sort non-staple mode. Staple and hole punch is not available.
- Paper between 80
*2 Available only when non-sort non-staple mode. Staple and hole punch is not available.
- Paper between 80
g
/m
2
and 209
g
/m
2
can be copied if the thick mode is used.
- The available paper sizes are specified for hole punch. Ask your service technician for details.
- “Maximum capacity” refers to the number of sheets when the paper recommended by Sharp is set.
- “Maximum capacity” refers to the number of sheets when the paper recommended by Sharp is set.
2. SETTING COPY PAPER
Acceptable Copy Paper Types and Sizes
For optimum copy quality, use the paper recommended by Sharp. Consult your service technician for details.
Plain Paper
(64
(64
-
80
g
/m
2
)
Thick 1
(
(
-
163
g
/m
2
)
Drawers
Feeder
Paper Type
Paper Size
Remarks
Tandem LCF
External LCF
(optional)
(optional)
Sheet Bypass
Plain Paper
(64
(64
-
80
g
/m
2
)
Thick 1
( - 163
( - 163
g
/m
2
)
Thick 2
( - 209
( - 209
g
/m
2
)
(Standard size)
A/B format: A3, A4, A4-R, A5-R, B4,
A/B format: A3, A4, A4-R, A5-R, B4,
B5,B5-R, FOLIO
LT format: LD, LG, LT, L T-R, ST-R,
COMP, 13" LG, 8.5" SQ
COMP, 13" LG, 8.5" SQ
(Non-Standard size)
Length: 100 - 305mm
Width: 148 - 457mm
Length: 100 - 305mm
Width: 148 - 457mm
Plain Paper
(64
(64
-
80
g
/m
2
)
Thick 1
(
(
-
163
g
/m
2
)
Thick 2
(
(
-
209
g
/m
2
)
Plain Paper
(64
(64
-
80
g
/m
2
)
Thick 1
(
(
-
163
g
/m
2
)
Thick 2
(
(
-
209
g
/m
2
)
Thick 2
(
(
-
209
g
/m
2
)
Tracing Paper
OHP film
(Standard size)
A4
A4
(Standard size)
A4
A4
*1
*1,*2
(Standard size)
A4, LT
Tab paper
(Standard size)
A4, LT
*1
100 sheets (80
g
/m
2
)
Tab paper
(Standard size)
A4, LT
Only the 2nd drawer can be
set *1
set *1
4000 sheets (80
g
/m
2
)
2500 sheets (80
g
/m
2
)
500 sheets (80
g
/m
2
)
(Standard size)
A/B format: A3, A4, A4-R, A5-R,
A/B format: A3, A4, A4-R, A5-R,
B4 (257 x 364mm),
B5 (257 x 182mm),
B5-R (182 x 257mm),
FOLIO (210 x 330mm),
LT format: LD (11"
B5-R (182 x 257mm),
FOLIO (210 x 330mm),
LT format: LD (11"
x
17"),
LG (8½"
x 14"), LT (11” x 8½"),
LT -R (8½"
x 11"), ST-R (5½"
x
8½"),
COMP (10
1
/
8
"x 14"), 13" LG (8½” x 13"),
8.5" SQ (8½" x 8½")
Click on the first or last page to see other AR-651 (serv.man25) service manuals if exist.