DOWNLOAD Sharp PN-655RE (serv.man3) Service Manual ↓ Size: 6.11 MB | Pages: 80 in PDF or view online for FREE

CODE : 00Z

CONTENTS

Parts marked with "

" are important for maintaining the safety of the set. Be sure to replace these parts with spec-

ified ones for maintaining the safety and performance of the set.

PN655RUSME

■ LEAD-FREE SOLDER

PN-655RU/655RE   

■ Mounting precautions

This monitor should be used at an ambient temperature between 32 °F
(0 °C) and 104 °F (40 °C). Provide enough space around the monitor

to prevent heat from accumulating inside.

If it is difficult to provide such space because the monitor is installed

inside a housing or for other reasons, take other measures to keep the

ambient temperature between 32 °F (0 °C) and 104 °F (40 °C) such as
installing a fan in the housing.

■

The carrying handles are detachable. When carrying the monitor,

attach the four supplied carrying handles to the monitor as shown
below. To attach the carrying handles, remove the existing screws from

the monitor, and attach the handles with the supplied screws.

After you removed the handles, be sure to replace the removed screws

in the original holes.

■

Note that the values shown are approximate values.

When mounting the monitor, read the manual of the brackets or stand for their mounting procedure. The screw holes for mounting brackets (M10 

u

4 holes) are provided on the rear of the monitor. Note that screw hole depth of the monitor is 1-3/16 inch (30mm). Loose holding may cause the prod-

uct to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 3/4 inch (20mm)
length of thread. SHARP recommends using mounting interface that comply with UL1678 standard.

11-13/16 [30]

1-3/4 [4.5]

1-15/16 [5]

1-15/16[5]

1-15/16 [5]

Unit: inch [cm]

The Power LED must be on the lower side.

59-

7

/ 16

 [1509]

Opening height (56-

3

/ 8

 [1432])

61-

7

/ 8

 [1572]

25-

9

/ 16

 [650]

34-5/16 [871]

Unit: inch [mm]

1/4 [6] 5-7/8 [150]

36-5/16 [923]

Opening width

31-3/4 [807]

39-1/2 [1003]

17-5/16 [440]

1-9/16
    [40]

1-9/16
[40]

Screw holes for mounting brackets

PN-655RU/655RE   LEAD-FREE SOLDER

■ LEAD-FREE SOLDER

The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The
alphabet following the “LF” mark shows the kind of lead-free solder. 

When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a breakdown or an

accident. 

Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use solder-

ing iron is recommendable. 

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity
is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may

exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is

confirmed. 

Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.  

If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after com-
pletion of soldering work. 

If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer. 

5mm

Lead-Free

Solder composition 
code (Refer to the 
table at the right.)

Solder composition

Sn-Ag-Cu

Sn-Ag-Bi
Sn-Ag-Bi-Cu

Sn-Zn-Bi

Sn-In-Ag-Bi

Sn-Cu-Ni

Sn-Ag-Sb

Bi-Sn-Ag-P
Bi-Sn-Ag

a

b

z

i

n

s

p

Solder composition code

a

PN-655RU/655RE

OUTLINE OF THE PRODUCT, NOMENCLATURE AND FUNCTION

1 – 1

■

Note: As a part of our policy of continuous improvement, SHARP 

reserves the right to make design and specification changes for 

product improvement without prior notice. 

The performance specification figures indicates are normal val-

ues of production units. There may be some deviation from these

values in individual units.

■

Note: that the values shown are approximate values.

When mounting the monitor, read the manual of the brackets or stand

for their mounting procedure.

The screw holes for mounting brackets (M10 

×

 4 holes) are provided on

the rear of the monitor. Note that screw hole depth of the monitor is 1-3/

16 inch (30 mm). Loose holding may cause the product to fall, resulting

in serious personal injuries as well as damage to the product. The
screw and hole should come together with over 3/4 inch (20 mm) length

of thread. SHARP recommends using mounting interface that comply

with UL1678 standard.

Model

PN-655RU/RE

LCD element

65" wide (163.9 cm diagonal)
ASV low-reflection black TFT LCD

Max. resolution

(pixels) 1920 

×

 1080

Max. colors

16.77 M colors (8 bits/color)

Pixel pitch

0.744mm (H) 

×

 0.744mm (V)

Viewing angle

170° right/left/up/down
(contrast ratio

>

10)

Screen active area

inch (mm)

31-5/8 (H) 

×

 56-1/4 (V) (804 

×

 1428)

Computer input signal

Analog RGB (0.7Vp-p) [75

Ω], 

Digital (DVI 1.0 standard-compliant)

Sync
signal

Horizontal/vertical separate
(TTL: positive/negative), Sync-on-green,
Composite sync (TTL: positive/negative)

Video color system

PAL, PAL-60, SECAM, NTSC (3.58MHz),
NTSC (4.43MHz)

Plug and play

VESA DDC2B

Power management

VESA DPMS, DVI DMPM

Input terminals

Computer
signal

Analog Mini D-sub 15 pin,

3 rows  

×

 1

Digital

DVI-D 24 pin 

×

 1

Computer
audio

3.5 mm mini stereo jack 

×

 1

Serial
(RS-232C)

D-sub 9 pin 

×

 1

Composite
video

BNC 

×

 1

Component BNC (Y, Cb/Pb, Cr/Pr)  

×

 1

Audio

RCA pin (L/R) 

×

 1

Output terminals

Computer
signal

Digital

DVI-D 24 pin 

×

 1

Serial
(RS-232C)

D-sub 9 pin 

×

 1

Audio

RCA pin (L/R) 

×

 1

Speaker

10 W 

+

 10 W [6

Ω]

Power requirement

AC 120 V, 60 Hz(PN-655RU) /
AC 100V-240V, 50/60Hz (PN-655RE)

Operating
temperature

32 °F to 104 °F (0 °C to 40 °C)

Operating humidity

20% to 80% (no condensation)

Power consumption

560 W (Input signal waiting mode: 1.5 W,
Standby mode: 1.5 W)

Dimensions

inch (mm) Approx. 36-5/16 

×

 5-7/8 

×

 61-7/8

(923 

×

 150 

×

  1,572)

(excluding protrusions)

Weight 

lbs. (kg) Approx. 145.5 (66)

Unit: inch [mm]

Opening width 

(31-

3

/

4

 [807])

34-

5

/

16

 [871]

Opening height (56-

3

/

8

 [1432])

61-

7

/

8

 [1572]

5-

7

/

8

 

[150]

1

/

4

 [6]

1-

9

/

16

[40]

1-

9

/

16

[40]

59-

7

/

16

 [1509]

17-

5

/

16

 [440]

39-

1

/

2

 [1003]

36-

5

/

16

 [923]

25-

9

/

16

 [650]

Screw holes 
for mounting brackets