Panasonic CF-08TX1BX1M Service Manual ▷ View online
9-1
9 Disassembly/Reassembly
Note:
Power off the computer. Do not shut down to the Suspend or hibernation mode.
Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.
Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.
9.1.
Disassembly Instructions
9.1.1.
Preparation
Be sure to make the following preparations before disassem-
bling.
bling.
• Shut down Windows and turn off the power.
• Disconnect the AC adaptor.
• Remove other devices if they are connected.
• Disconnect the AC adaptor.
• Remove other devices if they are connected.
Attention:
• Please execute writing BIOS ID when you exchange the
Main Board.
• Parts (Sheet and rubber) etc. related various the Conductive
Cloth and Heat Spreader cannot be recycled. Use new parts.
9.1.2.
Removing the Battery Pack
1. Open the hand strap cover.
2. Remove the hand strap.
3. Slide the Battery cover latch.
4. Open and remove the Battery cover.
4. Open and remove the Battery cover.
5. Pull the tab of the Battery Pack and remove it from the
wireless display.
6. Attach the hand strap.
7. Close the hand strap cover.
9.1.3.
Removing the Display Unit
1. Remove the two Screws <N4> and the Antenna Cover L.
2. Remove the two Screws <N4> and the Antenna Cover R.
2. Remove the two Screws <N4> and the Antenna Cover R.
hand strap cover
hand strap
battery cover latch
battery cover
battery pack
wireless display
hand strap
hand strap cover
Antenna
Cover L
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N6>
<N4>
<N4>
<N4>
Rear Cabinet
<N4>
<N6>
<N6>
Antenna
Cover R
9-2
3. Remove the 12 Screws <N6>.
4. Remove the Cable Hold Sheet while opening the Rear
Cabinet ASS'Y slowly.
5. Remove the Cable hooked on the Lamp Cable Spring.
6. Remove both the Inverter and the Inverter Case.
7. Remove the Connector (CN6) connected to the IO Power
6. Remove both the Inverter and the Inverter Case.
7. Remove the Connector (CN6) connected to the IO Power
PCB.
8. Open the Rear Cabinet.
9. Remove the Clamper and the Connectors (CN2, CN6)
connected to the Main PCB.
10. Remove the Display Unit.
Screws <N4>:DXSB2+6FNL
Screws <N6>:DXYN26+J6FNL
Screws <N6>:DXYN26+J6FNL
9.1.4.
Removing the Main PCB
1. Disconnect the seven Cables from the Connectors
(CN3,CN4,CN7,CN9,CN10,CN12,CN13).
2. Remove the four Screws <N2>.
3. Remove the PCB Reinforce Plate and the Main PCB.
3. Remove the PCB Reinforce Plate and the Main PCB.
Screws <N2>:DRSB2+5FKL
9.1.5.
Removing IO Power PCB
1. Disconnect the Cable from the Connector (CN8).
2. Remove the Edge Sheet.
3. Remove the eight Screws <N1>.
4. Remove the IO Power PCB.
2. Remove the Edge Sheet.
3. Remove the eight Screws <N1>.
4. Remove the IO Power PCB.
Screws <N1>:XSB2+4FNL
Lamp Cable Spring
Cable Holder Sheet
Rear Cabinet
IO Power P.C.B.
Inverter
Connector(CN6)
Cable
Display
Unit
Connector
(CN2)
Connector
(CN6)
Main P.C.B.
Clamper
<N2>
<N2>
<N2>
<N2>
Connector(CN7)
Connector(CN3)
Connector(CN13)
Connector(CN4)
Connector(CN9)
Connector(CN3)
Connector(CN13)
Connector(CN4)
Connector(CN9)
Main P.C.B.
Connector(CN12)
Connector(CN10)
PCB Reinforce Plate
Connector(CN8)
IO Power P.C.B.
Edge Sheet
<N1>
<N1>
<N1>
<N1>
<N1>
<N1>
<N1>
<N1>
9-3
9.1.6.
Removing the WLAN PCB
1. Remove the two Antenna Cables.
2. Remove the four Screws <N1>.
3. Remove the Lamp Cable Spring.
4. Remove the WLAN PCB.
2. Remove the four Screws <N1>.
3. Remove the Lamp Cable Spring.
4. Remove the WLAN PCB.
Screws <N1>:XSB2+4FNL
9.1.7.
Removing the Audio Con PCB
1. Disconnect the Cable from the Connector (CN300).
2. Remove the Edge Sheet.
3. Remove the two Screws <N1>.
4. Remove the Audio Con PCB.
2. Remove the Edge Sheet.
3. Remove the two Screws <N1>.
4. Remove the Audio Con PCB.
Screws <N1>:XSB2+4FNL
9.1.8.
Removing the Speaker
1. Remove the two Screws <K1-1-2>.
2. Remove the Speaker Hold Sheet.
3. Remove the Speaker fixed with the two-sided tape.
2. Remove the Speaker Hold Sheet.
3. Remove the Speaker fixed with the two-sided tape.
Screws <K1-1-2>:XSB2+4FNL
9.1.9.
Removing the USB PCB
1. Remove the two Screws <N1>.
2. Disconnect the Cable from the Connector (CN400).
3. Remove the USB Hold Plate and the USB PCB.
2. Disconnect the Cable from the Connector (CN400).
3. Remove the USB Hold Plate and the USB PCB.
Screws <N1>:XSB2+4FNL
Antenna Cable
WLAN P.C.B.
Antenna Cable
Lamp Cable Spring
<N1>
<N1>
<N1>
<N1>
B
A
A
B
<N1>
<N1>
Edge Sheet
Audio Con P.C.B.
Connector(CN300)
<K1-1-2>
<K1-1-2>
Speaker Hold Sheet
Speaker
Connector(CN400)
USB P.C.B.
USB Hold Plate
<N1>
<N1>
9-4
9.1.10. Removing the WLAN L PCB
1. Remove the Insulation Sheet.
2. Remove the Screw <N7>.
3. Remove both the Antenna Cable and the WLAN L PCB.
2. Remove the Screw <N7>.
3. Remove both the Antenna Cable and the WLAN L PCB.
Screw <N7>:DFHE5025XA
9.1.11. Removing the Bluetooth WLAN R
PCB
1. Remove the two tapes.
2. Remove the Screw <N7>.
3. Remove both the Antenna Cable and the Bluetooth
2. Remove the Screw <N7>.
3. Remove both the Antenna Cable and the Bluetooth
WLAN R PCB.
Screw <N7>:DFHE5025XA
9.1.12. Removing the Dock Con PCB
1. Remove the FFC Hold Cushion.
2. Disconnect the two Cables from the Connectors
2. Disconnect the two Cables from the Connectors
(CN600,CN601).
3. Remove the five screws <N3>.
4. Remove the Base Joint Cover, the Docking PCB Sheet
4. Remove the Base Joint Cover, the Docking PCB Sheet
and the Dock Con PCB.
Screws <N3>:DXQT26+D5FNL
9.1.13. Removing the SW LED PCB
1. Remove the three Screws <N2>.
2. Remove the SW Board Stopper Plate.
3. Disconnect the two Cables from the Connectors
2. Remove the SW Board Stopper Plate.
3. Disconnect the two Cables from the Connectors
(CN500,CN501).
4. Remove the SW LED PCB.
Screws <N2>:DRSB2+5FKL
<N7>
Insulation Sheet
WLAN L P.C.B.
Antenna Cable
<N7>
Tape
Blue tooth
WLAN R P.C.B.
Antenna
Cable
FFC Hold Cushion
Dock Con P.C.B.
Connector(CN600)
Connector(CN601)
<N3>
<N3>
<N3>
<N3>
<N3>
Dock Con P.C.B.
Docking P.C.B. Sheet
Docking P.C.B. Sheet
Base Joint Cover
<N2>
<N2>
<N2>
SW LED P.C.B.
SW Board Stopper Plate
Connector(CN501)
Connector(CN500)
Click on the first or last page to see other CF-08TX1BX1M service manuals if exist.