Panasonic CF-08TX1BX1M Service Manual ▷ View online
9-9
9.2.4.
Setting the Dock Con PCB
1. Fix the Docking PCB Sheet, the Base Joint Cover and the
Dock Con PCB using five Screws <N3>. No1 to No5
2. Connect the two Cables to the two connectors (CN600,
CN601) of the Dock Con PCB.
3. Attach the FFC Hold Cushion.
Note:
Tighten the Screws in the numbered order (No1 to
No5).
No5).
Screws <N3>:DXQT26+D5FNL
<N3>
<N3>
<N3>
<N3>
<N3>
Dock Con P.C.B.
Docking P.C.B. Sheet
Docking P.C.B. Sheet
Base Joint Cover
No.1
No.2
No.3
No.4
No.5
FFC Hold Cushion
Dock Con P.C.B.
Connector(CN600)
Connector(CN601)
9-10
n
Assembly of the DOCK CON PCB
Base Joint Cover
Docking PCB Sheet
FFC Hold Cushion
Cradle
Relay Card
FFC
(Docking Card)
Busterade
Screw-4
Screw-3
Screw-5
Screw-1
Screw-2
Caption Tape
0~1mm
10+1mm
Ensure the
direction is right.
Attach to the
top side of CN.
Attach.
Docking
PCB side
Attach the Hook firmly.Ensure
the Connector Terminals of the
Sheet ( Docking PCB sheet) do
not run over.
(Attach in the arrow direction
horizontally.)
Match to the end of the
Connector. (0 to 1 mm)
Screw-1->Screw-5
Match to the center of
Mg square hole. (– 1 mm)
stiffening plate side
Check Insert/Lock.
Rear Case Assy
Docking Cover Sheet
Asymmetric shape
Order of fixing
9-11
9.2.5.
Setting the Bluetooth WLAN R PCB
1. Fix the Antenna Cable and the Bluetooth WLAN R PCB
using one Screw <N7>.
2. Fix the Antenna Cables with the two tapes.
Screw <N7>:DFHE5025XA
9.2.6.
Setting the WLAN L PCB
1. Fix the Antenna Cable and the WLAN L PCB using one
Screw <N7>.
2. Fix the Antenna Cable with the Insulation Sheet.
Screw <N7>:DFHE5025XA
n
Assembly of the Antenna PCB
<N7>
Tape
Blue tooth
WLAN R P.C.B.
Antenna
Cable
<N7>
Insulation Sheet
WLAN L P.C.B.
Antenna Cable
Antenna PCB(WLAN)
Antenna PCB(BT)
ANT Cable Packing
Screw
Screw
Press fit.
Insert until it reaches
the brim.
Press fit.
Insert until it reaches
the brim.
9-12
9.2.7.
Setting the USB PCB
1. Fix the USB Hold Plate and the USB PCB using two
Screws <N1>.
2. Attach the Edge Sheet.
Screws <N1>:XSB2+4FNL
9.2.8.
Setting the Speaker
1. Attach the Speaker.
2. Fix the Speaker Hold Sheet using two Screws <K1-1-2>.
2. Fix the Speaker Hold Sheet using two Screws <K1-1-2>.
Screws <K1-1-2>:XSB2+4FNL
9.2.9.
Setting the Audio Con PCB
1. Connect the Cable to the Connector (CN300) of the Audio
Con PCB.
2. Fix the Audio Con PCB using two Screws <N1>.
3. Attach the Edge Sheet.
3. Attach the Edge Sheet.
Screws <N1>:XSB2+4FNL
Connector(CN400)
USB P.C.B.
USB Hold Plate
<N1>
<N1>
<K1-1-2>
<K1-1-2>
Speaker Hold Sheet
Speaker
<N1>
<N1>
Edge Sheet
Audio Con P.C.B.
Connector(CN300)
Click on the first or last page to see other CF-08TX1BX1M service manuals if exist.