Panasonic CF-08TX1BX1M Service Manual ▷ View online
9-5
9.1.14. Removing the LCD Unit and the
Inverter
1. Disconnect the Cable from the Inverter Connector.
2. Remove the Inverter with the Inverter Case.
3. Remove the Pet Tape.
2. Remove the Inverter with the Inverter Case.
3. Remove the Pet Tape.
4. Remove the TS Noise Tape.
5. Remove the Cable from the Clamper.
6. Remove the LCD Unit.
5. Remove the Cable from the Clamper.
6. Remove the LCD Unit.
Pet Tape
Inverter Case
Inverter
LCD Unit
Inverter
Connector
TS Noise Tape
LCD Unit
Clamper
Cable
9-6
9.2.
Reassembly Instructions
9.2.1.
Attention when CF-08 series is repaired
• Please execute writing BIOS ID when you exchange the Main Board.
• Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.
• Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.
9.2.2.
Setting the LCD Unit and the Inverter
1. Attach the LCD Unit.
2. Attach the TS Noise Tape.
3. Put the Cable into the Clamper.
2. Attach the TS Noise Tape.
3. Put the Cable into the Clamper.
4. Attach the Pet Tape.
5. Connect the Cable to the Inverter connector.
5. Connect the Cable to the Inverter connector.
TS Noise Tape
LCD Unit
Clamper
Cable
Pet Tape
Inverter Case
Inverter
LCD Unit
Inverter
Connector
9-7
9.2.3.
Setting the SW LED PCB
1. Connect the Cable to the connector (CN501) of the SW
LED PCB.
2. Attach the tape.
3. Fix the SW LED PCB and SW Board Stopper Plate using
3. Fix the SW LED PCB and SW Board Stopper Plate using
three Screws <N2>. No1 to No3
4. Put the Cable into the Clamper.
Note:
Tighten the Screws in the numbered order (No1 to No3).
Screws <N2>:DRSB2+5FKL
<N2>
<N2>
<N2>
SW LED P.C.B.
SW Board Stopper Plate
Connector(CN501)
Connector(CN500)
No.3
No.1
No.2
9-8
n
Assembly of the SW LED PCB
LED Lens
SW Rubber
Power Button
SW
Board
Tape
SW
Board
Stopper
Plate
Screw-2
Screw-3
Screw-1
Tape
Scroll Button
User Button
1~2mm
0~1mm
Asymmetric shape
Ensure it is attached
in the notch.
in FPC direction
Place the stiffening
plate downward.
After attaching FPC, put the
Board and fix it with a tape:
CN edge standard.
Press the scroll
button. (3.0 to
4.0 Kgf)
Order of fixing
Screw-1->Screw-3
Screw-1->Screw-3
Keep 1 mm or more.
Fix with the Tape using
the rib as a guide.
Lens Sheet
Match to the lateral side of the boss
and attach to the top side of the lens.
Inverter CN Tape
Inverter Case
Inverter
Fix Tape
Clamper
Clamper
SW Card Cable
Inverter
Cable
Inverter
Lamp CN
Match the end.
Important Parts for Safety
After passing the case
through, attach to the back
side of the Board.
Remove the Release
Paper on the back
side and attach it,
matching it to the edge
of the case.
Match.
0 to 1 mm
from the line
0 to 1 mm
from the line
Note)Avoid any stress on
the transformer of the
Inverter and the coil.
Ensure the Cable does
not run over the LCD Frame.
Pass the Cable between
the Board and rib.
Pass it through the clamper.
Wrap around the Conductive Cloth on this side.
Pass it through
the clamper.
Lamp CN
Safety Working
Safety Working
Safety Working
Safety Working
Click on the first or last page to see other CF-08TX1BX1M service manuals if exist.