Panasonic KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN Service Manual ▷ View online
33
7.2.3.
Cleaning-2 (Others)
When an Exit Sensor error has still occurred, clean the sensor with the following procedure.
7.2.3.1.
Exit Sensor (Board)
(1) Remove the Exit Plate. (See 8.3.15.)
(2) Blow off the dust on the surface of the Exit Sensor with the
accessory blower.
(2) Blow off the dust on the surface of the Exit Sensor with the
accessory blower.
34
7.3.
Replacing Limited Life Parts
7.3.1.
Replacing Paper Feed Roller
7.3.2.
Replacing Separation Roller
(1) Turn off the scanner.
(2) Remove the current Paper Feed Roller. (See 8.3.20.)
(3) Open the optional Roller Exchange Kit (KV-SS033), and then
take out a new Paper Feed Roller.
take out a new Paper Feed Roller.
(4) Install the Paper Feed Roller to both sides of the roller shaft
until it clicks into place, while releasing the tip of the lever on
the roller.
Note:
until it clicks into place, while releasing the tip of the lever on
the roller.
Note:
After reassembling the Paper Feed Roller, check the
roller's lever-lock is fixed on the groove of the roller
shaft by pulling the roller in the direction of the arrow.
roller's lever-lock is fixed on the groove of the roller
shaft by pulling the roller in the direction of the arrow.
(1) Turn off the scanner.
(2) Remove the current Separation Roller. (See 8.3.21.)
(3) Open the optional Roller Exchange Kit (KV-SS033), and then
take out a new Separation Roller.
take out a new Separation Roller.
(4) Install the Separation Roller to both sides of the roller shaft
until it clicks into place, while releasing the tip of the lever on
the roller.
Note:
until it clicks into place, while releasing the tip of the lever on
the roller.
Note:
After reassembling the Separation Roller, check
the roller's lever-lock is fixed on the groove of the
roller shaft by pulling the roller in the direction
of the arrow.
the roller's lever-lock is fixed on the groove of the
roller shaft by pulling the roller in the direction
of the arrow.
35
7.3.3.
Replacing DFP Roller
(1) Turn off the scanner.
(2) Remove the current DFP Roller. (See 8.3.8.)
(3) Open the optional Roller Exchange Kit (KV-SS033), and then
take out a new DFP Roller.
take out a new DFP Roller.
(4) Install the new DFP Roller with the groove of its shaft that is
located on the right, as seen from the front.
located on the right, as seen from the front.
Note:
After replacing the Paper Feed Roller, Separation
Roller, and DFP Roller, execute “Clear Counter for
replacing roller” with Service Utility. (See 9.3.4.)
Roller, and DFP Roller, execute “Clear Counter for
replacing roller” with Service Utility. (See 9.3.4.)
36
8 DISASSEMBLY INSTRUCTIONS
8.1.
Disassembly Flowchart
The flowchart indicates disassembly sequence for the Exterior, Mechanical parts, Unit Components, and Circuit Board
assemblies.
When reassembling, perform the steps in the reverse order unless otherwise instructed in Reassembling Notes.
assemblies.
When reassembling, perform the steps in the reverse order unless otherwise instructed in Reassembling Notes.
Note:
Disassembly flowchart explanation
* This sample flowchart shows that, to disassemble C, the procedures 1 and 2 must be performed first before
proceeding to the procedure 3.
proceeding to the procedure 3.
Click on the first or last page to see other KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN service manuals if exist.