Panasonic KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN Service Manual ▷ View online
13
4.2.
DIMM Module Extension
A maximum of 1024 MB (total size for front and back sides) extended memory may be required depending on the combination of
the paper size, mode, and resolution. To determine how much extended memory is required for a certain configuration, refer to
Fig. 4.2.1 and Fig. 4.2.2.
the paper size, mode, and resolution. To determine how much extended memory is required for a certain configuration, refer to
Fig. 4.2.1 and Fig. 4.2.2.
Note 1:
If configurations requiring a lot of memory (high resolution, color mode, etc.) are used with
KV-S4065CL/S4065CW/S4085CL/S4085CW Series, the scanning will be suspended intermittently while the data is
being transferred to the computer.
As a result, the images may be disrupted slightly due to the effect of suspending the scanning.
In cases like this, the image quality will be improved by installing additional memory in the scanner.
To determine the amount of memory that is required to avoid suspending the scanning, refer to Fig.4.2.1. and Fig.4.2.2.
KV-S4065CL/S4065CW/S4085CL/S4085CW Series, the scanning will be suspended intermittently while the data is
being transferred to the computer.
As a result, the images may be disrupted slightly due to the effect of suspending the scanning.
In cases like this, the image quality will be improved by installing additional memory in the scanner.
To determine the amount of memory that is required to avoid suspending the scanning, refer to Fig.4.2.1. and Fig.4.2.2.
Note 2:
Originally, CONTROL Board has 32 MB memory built in.
Note 3:
For the additional memory, the scanner requires the same type of memories for each side (Front and Back)
to be installed at the same time. (For example: “128” means that you must install 128 MB of memory for front-side
scanning and 128 MB of memory for back-side scanning.)
to be installed at the same time. (For example: “128” means that you must install 128 MB of memory for front-side
scanning and 128 MB of memory for back-side scanning.)
Note 4: Recommended memory
(1) 144 pin SDRAM (Unbuffered SO-DIMM)
(2) Non ECC
(3) + 3.3 V ± 0.3 V power supply
(4) Frequency / CAS Latency: 100 MHz / CL=2 or 133 MHz / CL=2
(5) Support for Full Page Burst
(6) Memory size: 128 MB, 256 MB, or 512 MB
(7) Height: Less than 31.75 mm (1.25 in.)
(2) Non ECC
(3) + 3.3 V ± 0.3 V power supply
(4) Frequency / CAS Latency: 100 MHz / CL=2 or 133 MHz / CL=2
(5) Support for Full Page Burst
(6) Memory size: 128 MB, 256 MB, or 512 MB
(7) Height: Less than 31.75 mm (1.25 in.)
Note 5: “X”
“X” in the Fig. 4.2.1 and Fig. 4.2.2 means the scanning will be suspended intermittently (START/STOP function
will operate.) even if the maximum amount of memory (total 1024 MB) is installed.
will operate.) even if the maximum amount of memory (total 1024 MB) is installed.
14
15
4.3.
Installing DIMM Modules
1. Remove the Right Cover. (See 8.2.1.)
2. Remove the screw (a), screw (b), and 2 screws (c) from the back. (See 8.4.1-(2).)
3. Remove the screw from the right. (See 8.4.1-(3).)
4. Release the connector wires from the 3 wire clamps. (See 8.4.1-(4).)
5. Pull out the Board Plate Assembly after releasing the connector wires from the 5 wire clamps. (See 8.4.1-(5).)
6. Insert the DIMM modules completely into the connectors’ (CN 1020, CN1021: Regarding each location, see 8.4.1.) slots.
2. Remove the screw (a), screw (b), and 2 screws (c) from the back. (See 8.4.1-(2).)
3. Remove the screw from the right. (See 8.4.1-(3).)
4. Release the connector wires from the 3 wire clamps. (See 8.4.1-(4).)
5. Pull out the Board Plate Assembly after releasing the connector wires from the 5 wire clamps. (See 8.4.1-(5).)
6. Insert the DIMM modules completely into the connectors’ (CN 1020, CN1021: Regarding each location, see 8.4.1.) slots.
16
4.4.
Connecting the Scanner to a Personal Computer
Connect the accessories’ Power Cord and USB cable to the back of the unit.
Note:
1. Power Cord shown on the above figure is for AC 100-120 V.
Caution:
1. Only use the Power Cord and USB Cable enclosed in this scanner.
2. Be sure to connect the scanner directly to the USB interface port on the PC.
We cannot guarantee that the scanner will work properly if it is connected to a USB hub.
2. Be sure to connect the scanner directly to the USB interface port on the PC.
We cannot guarantee that the scanner will work properly if it is connected to a USB hub.
Click on the first or last page to see other KV-S4065CL / KV-S4065CW / KV-S4065CWCN / KV-S4085CL / KV-S4085CW / KV-S4085CWCN service manuals if exist.