Sony NW-ZX100 / NW-ZX100HN Service Manual ▷ View online
37
NW-ZX100/ZX100HN
4-2. BATTERY SECTION
• Rear view
52
53
53
51
55
54
55
front panel section
ANT1
BAT1
A
A
B
B
1000
(SHEET (BT))
B
B
A
A
4.3
6
unit: mm
SHEET (BT)
$ERXW5HI1R
Please cut out and use POLYIMIDE SHEET for
a specified size when you exchange it for new parts.
Note 2: As for this part, the material or thickness
Please cut out and use POLYIMIDE SHEET for
a specified size when you exchange it for new parts.
Note 2: As for this part, the material or thickness
might be different compared with before.
However, there is no obstacle at all.
51
4-577-711-01 CUSHION, LCD FPC
52
4-475-089-01 SHEET
(BATT),
ADHESIVE
53
4-573-907-11 SCREW (NDS-EL) M1.4 (L=3 mm)
54
A-2079-566-A BT BOARD, COMPLETE
55
4-573-907-01 SCREW (NDS-EL) M1.4 (L=2 mm)
1000
9-913-402-43 POLYIMIDE SHEET (t=0.075) (for SERVICE)
ANT1
X-2592-382-1 SVX BASS PLATE ASSY (Including NFC antenna,
BT-VOL FPC board, Adhesive sheet (BATT),
Shield tape, Cushion) (See Note 3)
BAT1
X-2592-257-1 SVX BATTERY ASSY (Including BATT protection
sheet, Battery cushion (B)) (Except CH)
(See Note 1)
BAT1
X-2592-381-1 SVX BATTERY ASSY (CN) (Including BATT
protection sheet, Battery cushion (B),
Label (china battery)) (CH) (See Note 1)
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note 1:
• When the battery wire is removed, refer to “ABOUT INSULATING OF THE BATTERY ASSY
• When the battery wire is removed, refer to “ABOUT INSULATING OF THE BATTERY ASSY
(BAT1)” on page 4.
• When removing battery assy (Ref. No. BAT1) from the adhesive sheet (BATT) (Ref. No. 52), the
battery assy (Ref. No. BAT1) cannot be reused. Be sure to replace them with new parts.
• When disposing battery assy (Ref. No. BAT1), refer to “NOTE OF DISPOSAL OF THE BATTERY
ASSY (BAT1)” on page 4.
• The cushion installed on the battery assy (Ref. No. BAT1) have been deleted in the middle of produc-
tion, but there are no problems when replacing it.
For details, refer to “ABOUT CHANGES TO COMPONENTS OF THE BASS PLATE ASSY OR
BATTERY ASSY” on page 11.
Note 3: The cushions installed on the inside of the bass plate assy (Ref. No.
ANT1) have been deleted in the middle of production, but there are
no problems when replacing it.
no problems when replacing it.
For details, refer to “ABOUT CHANGES TO COMPONENTS OF
THE BASS PLATE ASSY OR BATTERY ASSY” on page 11.
THE BASS PLATE ASSY OR BATTERY ASSY” on page 11.
Ver. 1.1
38
NW-ZX100/ZX100HN
4-3. FRONT PANEL SECTION
MAIN board section
102
111
110
102
103
109
108
109
102
101
(See Note 1)
112
106
(See Note 2)
107
(See Note 2)
105
(See Note 2)
104
(See Note 2)
101
X-2592-234-2 SVX WINDOW ASSY (Including Window cushion)
(See Note 1)
102
4-573-907-11 SCREW (NDS-EL) M1.4 (L=3 mm)
103
X-2592-236-2 SVX 4D BUTTON ASSY (Including Button, Hinge,
Plate, SW rubber, W logo etc.)
104
4-571-676-01 RING (See Note 2)
105
4-573-921-01 SHEET, RING ADHESIVE (See Note 2)
106
4-571-675-01 CAP, BOTTOM (See Note 2)
107
4-573-920-01 SHEET, BTM CAP ADHESIVE (See Note 2)
108
4-484-509-01 GASKET
(JACK)
109
4-574-339-01 STEP SCREW (NDS-EL) M1.4 (L=1.6 mm)
110
X-2592-235-1 SVX SLOT GUIDE ASSY (Including Reset button)
111
X-2592-238-1 SVX LID, SLOT ASSY (Including O-ring, Spacer)
112
4-538-017-01 HI-RES
LABEL
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note 2: When removing the parts (Ref. No. 104, 105, 106, 107), these
parts are not re-used.
Be sure to replace these with new parts.
Note 1: The SVX window assy (Ref. No. 101) has been changed in the
middle of production. When replacing the SVX window assy (Ref.
No. 101), make sure to refer to “NOTES WHEN REPLACING
THE WINDOW ASSY OR CASE ASSY WITH THE DELETION
OF THE WINDOW SPACER” on page 10.
No. 101), make sure to refer to “NOTES WHEN REPLACING
THE WINDOW ASSY OR CASE ASSY WITH THE DELETION
OF THE WINDOW SPACER” on page 10.
Ver. 1.1
39
NW-ZX100/ZX100HN
4-4. MAIN BOARD SECTION
157
160
156
155
160
157
LCD section
SW board
MAIN board
not supplied
not supplied
HPJ1
151
151
154
161
158
159
153
152
153
152
C
D
D
C
1000
(SHEET, LID (PROTECT))
B
B
A
A
11
18
unit: mm
SHEET, LID (PROTECT)
$ERXW5HI1R
Please cut out and use POLYIMIDE SHEET for
a specified size when you exchange it for new parts.
Note 6: As for this part, the material or thickness
Please cut out and use POLYIMIDE SHEET for
a specified size when you exchange it for new parts.
Note 6: As for this part, the material or thickness
might be different compared with before.
However, there is no obstacle at all.
Note 5: Refer to page 5 for more about the pasting
position of the sheet (speaker).
=;+1
Note 1: When replacing the SW board, be sure the SW board and the
MAIN board replace both at the same time. The SW board
cannot replace with single.
cannot replace with single.
151
4-573-907-11 SCREW (NDS-EL) M1.4 (L=3 mm, Black)
(See Note 2)
151
4-573-907-41 SCREW (NDS-EL) M1.4 (L=2.5 mm, Silver)
(See Note 2)
152
3-254-135-01 SCREW (B1.4) (L=3 mm)
153
4-573-907-01 SCREW (NDS-EL) M1.4 (L=2 mm)
154
4-571-713-01 PLATE,
BOTTOM
155
4-571-709-01 PIN,
STRAP
156
4-573-907-21 SCREW (NDS-EL) M1.4 (L=4 mm)
157
3-234-449-27 SCREW (M1.4) (L=2.5 mm)
158
9-885-203-88 SVX MAIN BOARD ASSY
(Including MAIN board, 5PIN HP assy, PWB holder,
PWB assy plate, Sheet, Wire) (See Note 3, 4)
159
9-885-203-90 SVX MAIN-SW BOARD ASSY (Including MAIN
board, SW board, Adhesive sheet, PWB holder,
PWB assy plate, Sheet, Wire) (See Note 1, 3, 4)
160
4-573-907-31 SCREW (NDS-EL) M1.4 (L=5 mm)
161
4-577-712-01 SHEET, PWB SW ADHESIVE
1000
9-913-402-43 POLYIMIDE SHEET (t=0.075) (for SERVICE)
HPJ1
A-2092-992-A SVX 5PIN HP ASSY
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note 2: When replacing the screw (Ref. No. 151),
refer to “NOTE OF REPLACING THE
SCREWS (Except for Chinese model)”
on page 10.
SCREWS (Except for Chinese model)”
on page 10.
Note 3: When the MAIN board is replaced, re-
fer to “NOTE OF THE MAIN BOARD
ASSY REPLACING” on page 5.
ASSY REPLACING” on page 5.
Note 4: When complete MAIN board and SW
board are replaced, the data writing pro-
cessing etc. are necessary. For details,
refer to “ABOUT WORKING OF THE
BOARD REPLACING” on page 5.
cessing etc. are necessary. For details,
refer to “ABOUT WORKING OF THE
BOARD REPLACING” on page 5.
Ver. 1.1
40
NW-ZX100/ZX100HN
4-5. LCD SECTION
205
201
203
202
202
207
(See Note 2)
204
(See Note 1, 2)
LCD1
206
(See Note 1)
201
4-544-869-01 SHEET (FPC TP), PROTECTION
202
4-573-911-02 SPACER, LCD (SIDE)
203
4-573-910-01 SHEET, LCD (TOP) ADHESIVE
204
9-885-203-78 SVX CASE ASSY (Including Key, Knob) (AEP, UK)
(See Note 1, 2)
204
9-885-203-80 SVX CASE ASSY (Including Key, Knob) (EE)
(See Note 1, 2)
204
9-885-203-81 SVX CASE ASSY (Including Key, Knob)
(E, AUS, JE) (See Note 1, 2)
204
9-885-203-82 SVX CASE ASSY (Including Key, Knob) (CH)
(See Note 1, 2)
205
4-573-912-01 SHEET, FPC LCD ADHESIVE
206
4-582-384-01 SPACER, WINDOW (See Note 1)
207
4-586-693-01 SPACER, LID GUIDE (See Note 2)
LCD1 1-812-163-11 LCD
MODULE
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
Note 2: The lid guide spacer (Ref. No. 207) has been added in the
middle of production. When replacing the SVX case assy (Ref.
No. 204), refer to “NOTES WHEN REPLACING THE CASE
ASSY WITH THE ADDITION OF THE LID GUIDE SPAC-
ER” on page 11.
No. 204), refer to “NOTES WHEN REPLACING THE CASE
ASSY WITH THE ADDITION OF THE LID GUIDE SPAC-
ER” on page 11.
Ver. 1.1
Note 1: Along with changes to the SVX window assy (Ref. No. 101:
page 38), the window spacer (Ref. No. 206) has been deleted in
the middle of production. Attention is required when replacing
the SVX window assy (Ref. No. 101: page 38) or SVX case
assy (Ref. No. 204).
the middle of production. Attention is required when replacing
the SVX window assy (Ref. No. 101: page 38) or SVX case
assy (Ref. No. 204).
For details, refer to “NOTES WHEN REPLACING THE WIN-
DOW ASSY OR CASE ASSY WITH THE DELETION OF
THE WINDOW SPACER” on page 10.
THE WINDOW SPACER” on page 10.
Click on the first or last page to see other NW-ZX100 / NW-ZX100HN service manuals if exist.