Sony NW-ZX100 / NW-ZX100HN Service Manual ▷ View online
NW-ZX100/ZX100HN
13
Note: Follow the disassembly procedure in the numerical order given.
2-2. RING
2-3. BOTTOM CAP
– Rear view –
1 Insert a design knife etc. in the space
between the ring and the bottom cap
then remove the ring.
bottom cap
ring
top
bottom
2 Remove the ring block in
the direction of the arrow.
4 ring
Note: When removing this parts, it is not re-used.
Be sure to replace it with new parts.
3 ring adhesive sheet
Note: When removing this parts, it is not re-used.
Be sure to replace it with new parts.
– Rear view –
bottom cap
1 Insert a tweezers etc. in the groove of the bottom
cap then remove it.
top
2 Remove the bottom cap block
in the direction of the arrow.
4 bottom cap
Note: When removing this parts, it is not re-used.
Be sure to replace it with new parts.
3 BTM cap adhesive sheet
Note: When removing this parts, it is not re-used.
Be sure to replace it with new parts.
NW-ZX100/ZX100HN
14
2-4. REAR COVER ASSY, TOP CAP (B)
rear cover assy
case
– Rear view –
2 Peel the cover rear
adhesive sheet off
of this unit.
5 top cap adhesive sheet
3 rear cover assy
6 top cap (B)
1 Insert a tweezers etc. into the gap of the corner of
the upper end of the rear cover assy. Then carefully
peel the rear cover assy off with fingers.
Note: When removing the rear cover assy, please remove
carefully so as not to damage the case.
boss
boss
ditch
ditch
two claws
two projections
bottom
4 Remove the top cap (B) block
in the direction of the arrow.
guide line
(lower side)
(lower side)
guide line
(upper side)
(upper side)
1 cm
top
rear cover assy
1 Paste the rear cover
assy to the case.
3 Press the lower side.
2 Press the area of 1 cm of the upper side.
How to install the rear cover assy
4 Press the right
and left side.
2 Peel the cover rear
adhesive sheet off
of this unit.
NW-ZX100/ZX100HN
15
2-5. REAR PLATE (BOTTOM)
2-6. BATTERY BLOCK
– Rear view –
1 two screws
(M1.4) (L=4 mm)
4 rear plate (bottom)
3 sheet reset B
boss
hole
hole
boss
3DVWLQJSRVLWLRQRIWKHVKHHWUHVHW%
guide line
sheet reset B
rear plate (bottom)
2 Remove the rear plate (bottom) block
in the direction of the arrow.
top
bottom
– Rear view –
1 LCD FPC cushion
Switch to “HOLD off”.
case
battery block
LCD FPC cushion
LCD FPC
guide line
guide line
BT-VOL FPC
LCD FPC
3 BT-VOL FPC
connector
2 Remove three solders of the battery wire.
Note 2: When the battery wire is removed,
refer to “ABOUT INSULATING
OF THE BATTERY ASSY (BAT1)”
on page 4.
4 two screws (NDS-EL) M1.4
(L=3
mm)
5 battery block
3aVWiQJ SRViWiRQ RI WKe /&' )3&
FXVKiRQ
FXVKiRQ
+Rw WR iQVWaOO WKe EaWWer\ EORFN
:ire VeWWiQJ
MAIN board
Fix three wires under the
catcher of the holder PWB.
catcher of the holder PWB.
battery wire
[red]
[red]
battery wire
[black]
[black]
battery wire
[white]
[white]
holder PWB
Note 1: When installing the battery block,
align the position of switch of
battery block and HOLD switch
of
case.
top
bottom
catcher
NW-ZX100/ZX100HN
16
2-7. BT BOARD
2-8. BATTERY ASSY (BAT1), BASS PLATE ASSY (ANT1)
– Battery block front view –
– Rear view –
3 BT-VOL FPC connector
4 screw (NDS-EL) M1.4
(L=2
mm)
5 BT board
top
bottom
1 Unlock the
connector.
2 Draw the FPC out
of the connector.
4 screw (NDS-EL) M1.4
(L=2
mm)
– Battery block front view –
– Rear top view –
5 bass plate assy (ANT1)
bass plate
connector
guide line
sheet (BT)
bass plate
2 adhesive
sheet
sheet
(BATT)
adhesive sheet (BATT)
4 sheet (BT)
battery assy
bass plate assy
,QVWDOODWLRQSRVLWLRQRI
WKHEDWWHU\DVV\
WKHEDWWHU\DVV\
3DVWLQJSRVLWLRQRIWKHVKHHW%7
guide line
(center)
(center)
3DVWLQJSRVLWLRQRI
th
th
HDGKHVLYHVKHHW%$77
guide line
3 battery assy (BAT1)
Note
Note
1: When removing battery assy from
the adhesive sheet (BATT), the battery
assy cannot be reused.
Be sure to replace them with new parts.
Note 2: When disposing battery assy, refer to
“NOTE OF DISPOSAL OF THE
BATTERY ASSY (BAT1)” on page 4.
top
bottom
1 Remove the battery block in
the direction of the arrow.
Note 3: The cushions installed on the bass plate assy and battey assy have been deleted
in the middle of production, but there are no problems when replacing them.
For details, refer to “ABOUT CHANGES TO COMPONENTS OF THE BASS
PLATE ASSY OR BATTERY ASSY” on page 11. These illustrations and pic-
tures depict the cushions installed.
For details, refer to “ABOUT CHANGES TO COMPONENTS OF THE BASS
PLATE ASSY OR BATTERY ASSY” on page 11. These illustrations and pic-
tures depict the cushions installed.
Ver. 1.1
Click on the first or last page to see other NW-ZX100 / NW-ZX100HN service manuals if exist.