Sony NW-ZX100 / NW-ZX100HN Service Manual ▷ View online
NW-ZX100/ZX100HN
17
2-9. WINDOW
ASSY
2-10. 4D BUTTON ASSY
– Rear view –
– Front bottom view –
2 window assy
1 Insert a flat rod, etc. into the hole of
the case, and push in the direction
of the arrow to peel off the window
assy from the case.
Note: When removing the window assy,
remove so that you do not damage
the case. Also, if you use objects
with sharp tips such as tweezers,
you may damage the printed areas
of the window assy.
flat rod, etc.
window assy
When replacing the window assy with a new one, make sure to follow the procedure to below.
You cannot correctly install a new window assy while the window spacer is installed.
You cannot correctly install a new window assy while the window spacer is installed.
window assy
,QVWDOODWLRQSRVLWLRQRIWKHZLQGRZDVV\
1RWHVZKHQUHSODFLQJWKHZLQGRZDVV\
guide line
top
bottom
case
1 Remove the window assy
that needs to be replaced.
window
spacer
spacer
2 Check whether there is
a window spacer.
3 Peel off the window spacer.
4 Install a new window assy.
top
top
3URFHGXUH
If there is ĺ *o to step
3
If not ĺ *o to step
4
1 two step screws (NDS-EL) M1.4
(L=1.6
mm)
5 4D button assy
4D button assy
4 HI-RES label
HI-RES label
2 two screws (NDS-EL) M1.4
(L=3
mm)
3 Remove the 4D button block
in the direction of the arrow.
3DVWLQJSRVLWLRQRIWKH+,5(6ODEHO
top
bottom
–)URQWYLHZ–
1.4 ± 0.2 mm
1.4 ± 0.2 mm
Ver. 1.1
NW-ZX100/ZX100HN
18
2-11. SW BOARD
– Front view –
6 SW board
3 connector
5 PWB SW adhesive sheet
4 Remove the SW board
block in the direction
of the arrow.
1 two screws
(M1.4) (L=2.5 mm)
top
bottom
Note 3: When the SW board block is installed,
confirm that it is not overlapped.
SW board
case
– SW board rear view –
SW board
2 Insert tweezers, etc. into the cutout area of
the SW board as shown in the figure below,
and raise the SW board, and peel off the
adhesive
sheet.
Note
4: Be careful not to damage the mount part on
the rear side with the tips of the tweezers.
Note 5: Insert the tweezers
so that the tips hit
in this area.
Note 2: When removing SW board, please remove carefully
so as not to deform it.
When SW board is deformed, it is not re-used.
In this case, be sure to replace the SW board and
the MAIN board simultaneously.
2-12. SLOT LID ASSY, SLOT GUIDE ASSY
– Front view –
2 screw (NDS-EL) M1.4
(L=3
mm)
5 slot lid assy
3 claw
hole
6 slot guide assy
4 Remove the slot guide block
in the direction of the arrow.
1 Open the slot lid.
top
bottom
Note 1: The SW board cannot replace with single. If replace
the SW board, be sure to replace the MAIN board
simultaneously.
simultaneously.
Ver. 1.1
NW-ZX100/ZX100HN
19
2-13. MAIN BOARD BLOCK
OK
NG
– Rear view –
– Front view –
3 two screws (NDS-EL) M1.4
(L=3
mm)
Note: When replacing these screws, refer to
“NOTE OF REPLACING THE SCREWS
(Except for Chinese model)” on page 10.
4 Remove the MAIN board block
in the direction of the arrow.
5 MAIN board block
2 two screws (NDS-EL) M1.4
(L=5
mm)
1 LCD FFC connector
+ow to inVtaOO tKe /&' FF& FonneFtor
curved
folded
top
top
bottom
bottom
NW-ZX100/ZX100HN
20
2-14. MAIN BOARD ASSY
2-15. PWB PLATE ASSY
OK
NG
– MAIN board block front view –
– Rear view –
1 two screws (NDS-EL) M1.4
(L=2
mm)
2 screw
(B1.4) (L=3 mm)
2 screw
(B1.4) (L=3 mm)
4 gasket (jack)
5 bottom plate
top
bottom
hook
hook
hook
5 pin jack
5 pin jack
bottom plate
5 pin jack
bottom plate
3 Remove the bottom plate block
in the direction of the arrow.
6 strap pin
7 MAIN board assy
InVtallation direction for tKe bottoP Slate
– Bottom view –
2 screw (NDS-EL) M1.4
(L=4
mm)
3 PWB plate assy
1 lid (protect) sheet
lid (protect) sheet
PWB plate assy
3DVWLQJSRVLWLRQRIWKHOLGSURWHFWVKHHW
guide line
two bosses
two holes
Note: When the PWB plate assy is installed,
confirm that it is fit as shown below.
top
bottom
–0$,1ERDUGEORFNUHDUYLHZ–
Click on the first or last page to see other NW-ZX100 / NW-ZX100HN service manuals if exist.