Sharp MX-M950 / MX-MM1100 (serv.man40) Service Manual ▷ View online
MX-M1100 MAINTENANCE 9 – 17
6. Waste toner section
A. Maintenance table
✕: Check (Clean, replace, or adjust as necessary.) {: Clean ▲: Replace U: Adjust ✩: Lubricate : Shift the position
B. Details
1)
Open the front cover (a).
2)
Replace the waste toner bottle (a).
* Be sure to insert a new waste toner bottle securely to the
* Be sure to insert a new waste toner bottle securely to the
bottom.
3)
Attach the cap (a).
* Check to confirm that it is securely attached.
* Check to confirm that it is securely attached.
No.
Part name
When
calling
500
K
1000
K
1500
K
2000
K
2500
K
3000
K
Remark
[Refer to the Parts Guide. Block/Item No.]
(Only the replacement parts are described.)
1
Waste toner bottle (with cap)
✕
▲
▲
▲
▲
▲
▲
[PG No.: [75] - 26]
2
Gears
✕
3
Bearing (Waste toner resin bearing)
✕
1
2
3
3
3
a
a
a
MX-M1100 MAINTENANCE 9 – 18
7. Transfer section
A. Maintenance table
✕: Check (Clean, replace, or adjust as necessary.) {: Clean ▲: Replace U: Adjust ✩: Lubricate : Shift the position
No.
Part name
When
calling
500
K
1000
K
1500
K
2000
K
2500
K
3000
K
Remark
[Refer to the Parts Guide. Block/Item No.]
(Only the replacement parts are described.)
1
Transfer belt
{
✕
▲
✕
▲
✕
▲
Use dry cloth only. Never use alcohol.
[PG No.: [43] - 1]
When replacing, apply stearic acid. (UKOG-0312FCZZ)
[PG No.: [43] - 1]
When replacing, apply stearic acid. (UKOG-0312FCZZ)
2
Transfer roller
▲
✕
▲
✕
▲
✕
[PG No.: [43] - 29]
3
Transfer cleaning brush
✕
{
✕
{
✕
▲
[PG No.: [44] - 14]
4
Transfer cleaning blade
✕
✕
▲
✕
▲
✕
▲
[PG No.: [44] - 9]
5
Transfer sub blade
✕
✕
✕
✕
✕
✕
▲
[PG No.: [44] - 5]
6
Transfer side seal F, R
✕
✕
✕
✕
✕
✕
✕
7
Transfer drive roller
✕
8
Bearing (Waste toner resin bearing)
✕
9
Ball bearings
✕
10
Gears
✕
11
Ball bearing for transfer roller
✕
▲
✕
▲
✕
▲
[PG No.: [43] - 14]
12
Discharge plate
{
{
{
{
{
{
{
13
Discharge plate holder
{
{
{
{
{
{
{
1
5
3
7
2
4
11
9
11
13
12
8
9
6
6
8
8
9
11
11
MX-M1100 MAINTENANCE 9 – 19
B. Details
1)
Open the front cover (a), and pull out the intermediate frame
(b).
(b).
2)
Check the transfer belt (a) at every 500K.
3)
Remove the screw (a), and remove the cover (b).
4)
Remove the screw (a), and remove the cover (b).
5)
Remove the screw (a), and remove the holder (b).
6)
Remove the transfer belt unit (a).
7)
Remove the screw (a), and remove the bearing (b).
8)
Remove the transfer drive roller unit (a).
a
b
a
a
b
a
b
a
b
a
a
a
b
b
a
MX-M1100 MAINTENANCE 9 – 20
9)
Check the transfer drive roller (a), the gear (b) and the ball
bearings (c) at every 3000K.
bearings (c) at every 3000K.
10) Replace the transfer belt (a) at every 1000K.
* After replacement of the transfer belt, apply stearic acid
(UKOG-0312FCZZ) to all the circumference of the belt. After
assembling the unit, rotate it one revolution in the normal
direction.
assembling the unit, rotate it one revolution in the normal
direction.
* Use care so that the beats (b) on the both edges of the back
of the transfer belt are not on the drive roller and the follower
roller.
roller.
* Never apply powder other than stearic acid.
11) Check the transfer roller (a) and the ball bearing (b) for the
transfer roller at every 500K, and check each ball bearing (c) at
every 3000K.
every 3000K.
12) Remove the bearing (a) and the spring (b), and replace the ball
bearing (c) for the transfer roller and the transfer roller (d) at
every 1000K.
every 1000K.
13) Check the screw (a), and replace the transfer cleaning blade
(b) at every 500K, and replace it at every 1000K.
* Be careful not to touch the urethane edge of the transfer
* Be careful not to touch the urethane edge of the transfer
cleaning blade.
14) Check the side seal F (a) and the side seal R (b) at every
500K.
a
c
b
c
a
b
b
b
b
a
c
c
a
a
a
b
b
c
c
d
a
b
a
b
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man40) service manuals if exist.