Sharp MX-M950 / MX-MM1100 (serv.man40) Service Manual ▷ View online
MX-M1100 MAINTENANCE 9 – 33
24) Remove the screw (a), and remove the cover (b).
25) Disconnect the connector (a), and remove the screw (b).
Remove the WEB motor unit (c).
26) Remove the E-ring (a) and the gear (b), and check the web
motor (c) at every 500K or replace it at every 3000K.
27) Remove the screw (a), and remove the cover (b). Remove the
harness from the edge saddle (c). Remove the snap band (d)
and disconnect the connector (e). Remove the screw (f), and
remove the lower heat roller separation pawl unit (g).
* When disconnecting the connector (e), do not pull the har-
and disconnect the connector (e). Remove the screw (f), and
remove the lower heat roller separation pawl unit (g).
* When disconnecting the connector (e), do not pull the har-
ness but hold the connector section and pull it out.
28) Remove the spring (a), and replace the lower heat roller sepa-
ration pawl (b).
29) Remove the screw (a), and remove the cover (b).
a
a
b
a
c
b
b
a
b
c
a
a
b
e
d
f
g
c
a
b
a
a
b
MX-M1100 MAINTENANCE 9 – 34
30) Remove the screw (a). Slide the front upper paper guide (b),
and remove and replace it.
31) Remove the clip (a), and pull out the shaft (b). Open the paper
guide (c), and clean it at every 500K.
32) Remove the spring (a), and remove the lower heat roller unit
(b).
33) Remove the C-ring (a). Check the lower heat roller (b) and the
lower heat roller ball bearing (c) at every 500K or replace them
at every 1000K.
at every 1000K.
* When replacing, apply grease (UKOG-0235FCZZ) to each
section (a) of the lower heat roller.
34) Remove the E-ring (a), and remove the upper heat roller drive
gear (b) and the ball bearing (c).
Check the upper heat roller drive gear (b) at every 500K, or
replace it at every 3000K. Check the ball bearing (c) at every
3000K.
Check the upper heat roller drive gear (b) at every 500K, or
replace it at every 3000K. Check the ball bearing (c) at every
3000K.
a
b
b
c
a
a
a
b
c
b
c
a
a
a
a
a
b
c
c
MX-M1100 MAINTENANCE 9 – 35
11. Filter section
A. Maintenance table
✕: Check (Clean, replace, or adjust as necessary.) {: Clean ▲: Replace U: Adjust ✩: Lubricate : Shift the position
No.
Part name
When
calling
500
K
1000
K
1500
K
2000
K
2500
K
3000
K
Remark
[Refer to the Parts Guide. Block/Item No.]
(Only the replacement parts are described.)
1
Ozone filter
▲
▲
▲
▲
▲
▲
Or 6 months
[PG No.: [72] - 26]
[PG No.: [72] - 26]
2
Suction filter
▲
▲
▲
▲
▲
▲
Or 6 months
[PG No.: [70] - 35]
[PG No.: [70] - 35]
3
Exhaust filter
▲
▲
▲
▲
▲
▲
Or 6 months
[PG No.: [72] - 10]
[PG No.: [72] - 10]
3
2
1
MX-M1100 MAINTENANCE 9 – 36
B. Details
1)
Open the front cover (a).
2)
Remove the screw (a), and remove the cover (b). Replace the
suction filter (c).
suction filter (c).
3)
Remove the screw (a) on the back side of the machine, and
remove the cover (b). Replace the ozone filter (c).
* Attach so that the filter knob (d) comes on the left side as
remove the cover (b). Replace the ozone filter (c).
* Attach so that the filter knob (d) comes on the left side as
shown below.
4)
Remove the screw (a), and remove the cover (b). Replace the
exhaust filter (c).
* Attach so that the filter knob (d) comes on the left side as
exhaust filter (c).
* Attach so that the filter knob (d) comes on the left side as
shown below.
a
c
b
a
c
d
b
a
c
d
b
a
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man40) service manuals if exist.