DOWNLOAD Sharp MX-M904 / MX-M1204 (serv.man9) Service Manual ↓ Size: 27.84 MB | Pages: 127 in PDF or view online for FREE

MX-M1204  MX-RB13 (RELAY UNIT)  16 – 3

2)

Fix the latch receivers F/R (Packed items No.4, 5) with the
screws (Packed items No.2).

1)

Attach the Black Mylar (bundled with the inserter No.10) to the
paper guide D (Packed items No.9).

Attach the Black Mylar to the downstream side of the paper
guide.

Attach to the notch in the rear side as the reference.

2)

Fix the paper guide D (Packed items No.9) to the paper feed
side of the relay unit with the screws (Packed items No.1).

1)

Open the front cover of the relay unit, remove the screws and
pull the lock lever toward you.

2)

Connect the relay unit to the inserter or stacker. 
Insert the pin of the latch receiver into the hole in the relay unit.

3)

Push up the lock lever to fix the relay unit and the inserter or
stacker, and use the removed screw to fix the lock lever.

MEMO: If they cannot be locked, follow the installing proce-
dures (height adjustment) of the complex machine and options
to adjust the height.

 

R side

Black Mylar

Notch

MX-M1204  MX-RB13 (RELAY UNIT)  16 – 4

NOTE: When the adjuster bolt is turned counterclockwise, the

height is decreased. When turned clockwise, the height is
increased.

NOTE: For the height and tilt adjustment, use the three adjuster

bolts under the unit.

Turn the adjustment nuts of the casters with a wrench in the arrow
direction to adjust the height. (When turning the adjustment nut one
rotation, the height of the relay unit is changed by about 1.75mm.)

• To increase the relay unit height, turn the nut in the direction [A].

• To decrease the relay unit height, turn the nut in the direction [B].

NOTE: Use the wrench attached to the finisher.

1)

Adjust the adjuster bolt (1) so that the difference in heights in
the front side the relay unit and the connection unit is within
2mm.

2)

Adjust the adjuster bolt (1) so that the difference in heights in
the rear side the relay unit and the connection unit is within
2mm.

3)

Use adjuster bolt (3) so that the clearance between the
machine and the unit becomes uniform.

1)

Open the cover at the back of the finisher, and disconnect the
dummy connector.

2)

Attach the disconnected dummy connector to the saddle at the
right lower side to keep for future use. 
Pass the cable from the relay unit to the center saddle and fix
with the screw (Packed items No.2) to connect.

3)

Connect the two cables, and attach the cover.

 

Ԙ

 

Ԛ

 

ԙ

 

MX-M1204  MX-FD10 (FOLDING UNIT)  17 – 1

MX-M1204

Service Manual

 

NOTE: When moving the paper folding unit, use manpower of four

or more persons.

1)

Remove taping from the paper folding unit.

2)

Remove the L-shape angle brackets for the folding unit.  

Open the paper guide and remove the fixing angles as the pic-
ture below indicates.

NOTE: Remove the fixing bracket for pressure release (blue

circled section, two positions) with opening the paper
guide  after you open the fixing bracket for pressure
release (red circled section, four positions) with open-
ing the paper guide. Since it may drop inside the fixing
bracket unit, do not pull forcibly.

NOTE: The two screws (pointed to by screwdrivers) at the

front and rear are used to adjust the folding roller pres-
sure. Never loosen these screws.

MX-M1204  MX-FD10 (FOLDING UNIT)  17 – 2

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Fix the connection plates F/R (Packed items No.5) and the
connection pin (Packed items No.6) to the decurler unit with
the screws (Packed items No.4).

1

Plug cover

1

---

---

---

1

1

2

Screw 
(Bind, M4 x 7)

1

---

---

---

1

1

3

Power  relay  cable

1

1

1

1

1

1

4

Screw 
(RS tight, M4 x 8)

8

8

8

8

---

---

5

Connection plate

2

2

2

2

---

---

6

Positioning  pin

1

1

1

1

1

1

7

Screw 
(Bind, M4 x 10)

2

---

---

---

2

2

8

Shunt  cable

1

1

1

1

1

1

9

Wire  saddle

1

1

1

1

1

1

10

Cushion

1

1

1

1

1

1

2

1

6

5

4

3

7

8

9

10

Cushion attachment 
position

Reference of cushion on.
(Rear screw hole tiered edge)

Reference of cushion on.
(Upper cabinet lower edge)

 

: ‘17/Apr.