DOWNLOAD Sharp MX-M904 / MX-M1204 (serv.man9) Service Manual ↓ Size: 27.84 MB | Pages: 127 in PDF or view online for FREE

MX-M1204  MX-MF11 (MULTI BYPASS TRAY)  10 – 2

2)

Fix the bracket with the screw.

3)

Remove the multi bypass tray from the package.

NOTE: Use man power of two persons to lift the multi bypass

tray. (Refer to the figure below.)

1)

Remove the screws and remove the upper cabinet.

MEMO: Remove the paper feed section with shifting it to the
direction of the arrow.

2)

Mount the multi bypass tray on LCT and fix it with screws.

NOTE: Insert the connection pin to the positioning hole of the

multi bypass tray.

3)

Connect the harnesses to LCT.

MEMO: Wire the harnesses through the cable clamp.

Screw hole

Screw hole

 

Connection pin

Connection pin

 

MX-M1204  MX-MF11 (MULTI BYPASS TRAY)  10 – 3

4)

Fix the upper cabinet with the screws.

MEMO: After fixing the cabinet, shift the paper feed section to
the direction of the arrow.

5)

Open the front door of the LCT, and store the tab sheet
restraint plate to the place as shown in the figure below.

6)

Place the End fence as shown in the figure below.

'PFHGPEG

MX-M1204  MX-FN24/FN25 (FINISHER/SADDLE STITCH FINISHER)  11 – 1

MX-M1204

Service Manual

 

1)

When you take the finisher down from the skid, raise the upper
side of the finisher along with the skid after opening the plastic
bag. 
(Please see the pictures below.) 
Required persons to unpack the finisher: 2 or more.

NOTE: The stopper attached to the outer carton can easily be

removed if you use a screwdriver.

2)

Take off the locking tape and locking material.

* Unfasten the 3 level shoe bolts at the bottom of the finisher.

1

Tray (auxiliary)

1

2

Tray

1

3

Screw (M3 

✕ 8)

1

4

Screw (M3 

✕ 6)

4

5

Screw (M4 

✕ 10)

4

6

Tray (MX-FN25 only)

1

7

Sponge strip

1

8

Ground plate (3holes)

1

9

Leveling shoes *

3

10

Joint bracket L

1

11

Joint bracket R

1

12

Entrance guide plate

1

13

Staple position label (for scanner)

1

14

Staple position label (for DSPF)

1

15

Punch position label (for scanner)

1

16

Punch position label (for DSPF)

1

13

14

15

16

1

2

3

4

5

8

7

9

6

10

11

12

Stopper

MX-M1204  MX-FN24/FN25 (FINISHER/SADDLE STITCH FINISHER)  11 – 2

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1)

Attach ground plate (Packed items No.8), Sponge strip
(Packed items No.7), and entrance guide plate (Packed items
No.12) with the screws (Packed items No.4 Screw M3x6).

* Attachment criteria of the sponge

Attach the sponge along the inside edge of the frame and
the end of the upper cover.

* If you attach the punch unit, plase attach here.

2)

Attach joint brackets L/R to the main unit of the copier with the
screw (Packed items No.5 Screw M4x10).

3)

Take off the screw which secures the tie plate on the finisher,
pull the tie plate, then join the finisher and the main unit of the
copier slowly.

Put the tie plate back and fasten the screw to secure the tie
plate.

* Please adjust the height according to “The procedure for the

main unit and the option height adjustment” if you cannot
join the units. 

4)

Attach the connector.

5)

Attach the tray. (Packed items No.3 Screw M3x8)

6)

Attach the tray (Packed items No.6). (Only MX-FN25)

 

Entrance guide plate

Cushion

Earth plate : BKT

㪪㫇㫆㫅㪾㪼㩷㫊㫋㫉㫀㫇

Joint bracket L

Joint bracket R

The screw to fix the tie plate

Connector

 

Tie plate

Fix with screws. (backside)

Output tray