DOWNLOAD Sharp MX-M904 / MX-M1204 (serv.man9) Service Manual ↓ Size: 27.84 MB | Pages: 127 in PDF or view online for FREE

MX-M1204  MX-ST10/CA10 (HIGH CAPACITY STACKER/PAPER CART)  15 – 1

MX-M1204

Service Manual

 

1)

Remove the L-Plate (Total : pcs)

2)

* For European countries, there are three types of Power cords.  

1)

Always work on this unloading in a foursome.

2)

Lay your hands on the palette as shown in the photos below.

NOTE: Try not to lay your hands on the adjuster volts.

NOTE:  Before installation, be sure to turn both the operation and
main  power switches off and disconnect the power plug from the
power outlet. Make double sure that the data lamp on the operation
panel does not light up or blink when per- forming installation. 

-  Remove the paper cart from the stacker  before moving.

-  Fix the locking plate which were removed at  B-2) Remove the
Locking Plate.

1)

Attach the guide plate. 

Tighten the paper guide C (Packed item No. 13 with MX-RB18)
at the paper feed entry with screws (Packed item No. 1 with
the decurler). 

1

Handle

1

2

Stacker tray

1

3

Frame cart

1

4

Guide plate

1

5

Bracket

1

6

Earth plate

1

7

Paper holder

1

8

Adjuster support

4

9

Sems screw (M5 x 10)

2

10

Hexagonal screw (M3 x 6)

2

11

Bind screw (M4 x 8)

6

12 *

Power cord

1

13

Spacer molt

1

14

Guide mylar

1

15

Label

1

16

Connection Plate

1

Inside the front door

16

Right Side

TopPage

: ‘13/Oct

MX-M1204  MX-ST10/CA10 (HIGH CAPACITY STACKER/PAPER CART)  15 – 2

Attach the guide plate (Packed item No. 4) to the same posi-
tion as above with the screws (Packed item No. 10 x2).

a) Remove the screw. 

b) Attach the black Mylar.   

Attach the black mylar sheet to the paper guide along the ref-
erence line. For the reference, see the figure below.  

c) Fix the guide plate with the black mylar to the paper feed
part of the stacker with the screw (Packed items No.10 Hexag-
onal screw M3x6).  

1)

Tighten the earth plate (Packed item No.6) with screws
(Packed item No.11 x2). 

Insert the screw into the lower hole and tighten it. 

Insert the screw into the upper hole and tighten it. 

1)

Tighten the bracket (Packed item No. 5) to the connection
option with the screws (Packed item No. 11 x4). 

TopPage

: ‘13/Oct

MX-M1204  MX-ST10/CA10 (HIGH CAPACITY STACKER/PAPER CART)  15 – 3

1) Remove the cover. 

2)

Tighten the bracket (Packed item No. 5) to the connection
option with the screws (Packed item No. 11 x4).  

1) Open the front door, remove the screw and pull the lock lever

toward you.    

2)

Attach the cushion (Packed item No.13).    

3)

Connect the stacker.     

4)

Set the adjusters (Packed item No.8 x4).      

5)

 Adjust the height by turning the adjuster volts. 
Keep the height of the stacker in line with the one of the con-
nection.      

6)

 Push up the lock lever which was released in procedure 5) to
fix the unit and the connected machine, and tighten with
screws. MEMO: If the lock lever cannot be locked, adjust the
height of the connection option and the stacker again.       

When separated 
Execute procedure 5) to separate. 

7)

 Put the label (Packed items No.15)as shown in the figure. 

TopPage

: ‘13/Oct

MX-M1204  MX-ST10/CA10 (HIGH CAPACITY STACKER/PAPER CART)  15 – 4

1)

Remove the screw and remove the cover. 

1)

Remove the screws and remove the covers. 

2)

Install the connection plate (Packed item No.16) with screws
(Packed item No.11 X 2). 

 

The stacker unit ID must be set with the Dip Switch2 on the control
PWB.

The stacker unit ID setting is enabled only when in I/F with the
engine. 
Machine + Stacker unit + Finisher 

Machine + 2 Stacker units + Finisher  

Machine + Stacker unit   

Machine + 2 Stacker units  

Stacker 1

ID=0x41

1: off, 2

off 

Stacker 2

ID=0x42

Stacker 1

ID=0x41

1

on, 2off 1off, 2off 

Stacker 1

ID=0x4F

1

off, 2on 

Stacker 2

ID=0x4F

Stacker 1

ID=0x41

1

on, 2on

1

off, 2off 

TopPage

: ‘13/Oct