DOWNLOAD Sharp MX-M654N / MX-M754N (serv.man4) Service Manual ↓ Size: 76.53 MB | Pages: 127 in PDF or view online for FREE

MX-M754N  MX-FX11 (FACSIMILE EXPANSION KIT)  22 – 1

MX-M754N

Service Manual

 

*1: Not use these screws at installation.

NOTE: Before installation, be sure to turn both the operation and

main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.

1) Attach the step screw (M4) (Necessary items) to one of the

position from which the screws are removed.

2) Insert the step screw into the mounting hole of the fax unit

(Packed items).

3) Use a screw that has been removed in step 1) to secure the

fax unit.

1)

Remove the screw, and remove the right rear cabinet.

2)

Remove the screw, and pull out the MFP control unit.

1

Fax unit

1

2

Line cable

1

3

Ferrite core

2

4

Step screw (M4)

1

*1

5

Step screw (M3)

1

*1

6

M3  screw

1

7

Line cable

1

2

1

4

3

6

7

U.K

France

Ge rmany

Aust ralia

For other destinations

5

Ĭ

Ĭ

ĭ

Ĭ

ĭ

Ĭ

ĭ

Ĭ

: ‘14/Dec

MX-M754N  MX-FX11 (FACSIMILE EXPANSION KIT)  22 – 2

1) Connect the interface cable to the MFP control PWB.

NOTE: Check that the connector is not obliquely inserted.

2) Push the interface cable into the recessed portion of the sheet

metal on the MFP control unit.

3) Fix a snap band with the M3 screw (Packed items).

1) Attach the MFP control unit into the main unit, and fix the

screw.

2) Cut out the cut-out portion of the right rear cabinet.

3)

Fit the interface cable into the opening that has been cut. 
Attach the right rear cabinet, and fix the screw.

1)

Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.

1)

Enter the SIM26-6 mode.

2)

Check to confirm that the destination setting of the machine
matches the specifications of the FAX destination. If not, the
FAX may not function properly.

1)

Enter the SIM66-2 mode.

2)

Press DEST CODE button.

3)

Take a note of the corresponding destination code.

4)

Press BACK button to return to the code entry mode.

5)

Enter the destination code taken in procedure 3), and press
SET button.

6)

Press EXECUTE and YES buttons.

Ĭ

ĭ

Į

ĭ

Ĭ

ĭ

ĭ

Ĭ

MX-M754N  MX-FX11 (FACSIMILE EXPANSION KIT)  22 – 3

1) Connect the line cable (Packed items) on the line to the modu-

lar jack indicated as “LINE.”

MEMO: When connecting the line cable (to LINE or TEL), wind the
line cable two turns around the ferrite core (Packed items) as
shown in the figure, and connect to the modular jack which is
marked with “LINE.”

MEMO: After connection, perform the setting of “External tele-
phone connection" of the system setting (administrator).

About
10 cm

MX-M754N  AR-SU1 (STAMP UNIT)  23 – 1

MX-M754N

Service Manual

 

* When replacing the stamp cartridge, Refer to “Stamp cartridge

replacement” in the “User’s Guide” (PDF document) which is
stored in the hard disk of the machine. The user must be notified
of that. (Do not refer to “Stamp cartridge replacement procedure”
(Packed items).)

1) Open the DSPF unit, remove the OC mat.

2) Remove the screw, and remove the paper exit PG cover.

Remove the screw.
Disengage the pawl, and remove the stamp case unit.

3)

Attach the stamp unit (Packed items) to the stamp case which
was removed from the DSPF unit with the installing screw
(Packed items). (Fix it together with the earth wire.)

* Arrange the harness of the stamp unit as shown below.

4)

Install the stamp case unit, and fasten it with the screw. Install
the earth wire. Connect the connector.

5)

Install the paper exit PG cover.

1

Stamp  unit

1

2

Stamp cartridge replacement procedure*

1

3

Stamp cartridge

3

4

Installing screw

1