Sharp MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) Service Manual ▷ View online
MX-M264U MX-TE10 (EXIT TRAY UNIT) 8 – 2
7)
Wiring
8)
Install the paper exit right cover sub and tightening the screw.
3 x 4 screw (S) 2PCS
3 x 4 screw (S) 2PCS
9)
Install the right paper exit actuator and the paper holding arm.
10) Remove the screw and remove the paper exit fan connector
sheet.
11) Install the harness cover OP and tightening the screw.
Paper holding arm
Right paper
exit actuator
exit actuator
Insertion direction
Right paper exit paper
full detection fulcrum
full detection fulcrum
Insert it to the hole of the paper
exit right cover (R side, F side)
exit right cover (R side, F side)
MX-M264U MX-TR11 (JOB SEPARATOR) 9 – 1
MX-M264U
Service Manual
[9] MX-TR11 (JOB SEPARATOR)
1. Parts included
2. Installation
NOTE: Turn off the main switch of the machine and then remove
the power plug of the machine from the outlet.
1)
Remove the rear cabinet.
2)
Remove the right cabinet lever cover.
(Dispose of the part after installation)
(M4 x 12 P tight)
(Dispose of the part after installation)
(M4 x 12 P tight)
3)
Remove the right cabinet AS.
M4 x 10 P tight (2pcs)
M4 x 10 P tight (2pcs)
4)
Install the second paper exit UN.
M4 x 10 S tight (4pcs)
M4 x 10 S tight (4pcs)
5)
Connect the second paper exit UN connector to MCU UN.
Fixation treatment of the harness is required.
Fixation treatment of the harness is required.
6)
Disengage the pawls in the sequence of (1) and (2) and
remove the paper exit dummy cover.
remove the paper exit dummy cover.
Job separator unit
Second paper
exit tray holder
exit tray holder
Second paper exit unit
M4 x 10 (5 pcs.)
Mylar
*Not used.
1
2
1
1
2
MX-M264U MX-TR11 (JOB SEPARATOR) 9 – 2
7)
Remove the paper holding arm, install it to job separator AS.
(Same as the current state)
(Same as the current state)
8)
Install the second paper exit tray holder. (New part)
M4 P tight tightening
M4 P tight tightening
9)
Install the job separator tray AS.
10) Install the rail dummy cover part to the guide rail so that slide
the over part from front side to rear side.
After that, insert the rib of tray part to the location of insertion of
the second paper exit tray holder.
Check that it is caught while being pushing up the tray.
After that, insert the rib of tray part to the location of insertion of
the second paper exit tray holder.
Check that it is caught while being pushing up the tray.
11) Install the right cabinet AS.
M4 x 10 P tight (2pcs)
12) Install the rear cabinet.
13) Job separator setting in simulation 26-1.
Paper holding arm
MX-M264U MX-PB15 (PRINTER EXPANSION KIT) 10 – 1
MX-M264U
Service Manual
[10] MX-PB15 (PRINTER EXPANSION KIT)
1. Unpacking
A. Packed items check
2. Installation
A. Enable setting of functions
1)
Enter the product key to enable the functions.
a)
a)
Enter the system setting mode.
b)
The machine enters the product key input mode.
c)
Enter the product key.
d)
Press the registration key.
2)
After completion of the product key input, turn OFF the power
switch on the operation panel of the machine, and turn OFF
the main power switch.
switch on the operation panel of the machine, and turn OFF
the main power switch.
3)
Turn ON the main power switch and the power switch on the
operation panel.
operation panel.
B. Confirmation of function enable
Execute SIM22-10 (Machine configuration display) to check to con-
firm that the set functions are enable.
firm that the set functions are enable.
No.
Name
Quantity
1
CD-ROM
1
2
Operation manual
1
1
2
Click on the first or last page to see other MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) service manuals if exist.