Sharp MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) Service Manual ▷ View online
MX-M264U MX-FN23 (FINISHER) 7 – 3
11) Install the rear cabinet to the original position, and fix it with
screw.
12) Attach the rail dummy cover to the guide rail by sliding it along
the guide rail in the arrow direction as shown in the figure.
13) Remove round-head screw from the connection unit which is
packed with the finisher, and remove the front cabinet lower
and the connection cabinet temporarily.
and the connection cabinet temporarily.
14) Slide the rail under the connection unit to the lock position.
15) Engage the finisher connection plate with the notch in the stay
at the right bottom of the machine.
Slide the connection plate to the bottom, and attach M3 screw
as shown. (Use the screw bundled to the package.)
MEMO: Press the right side of the connection plate.
Slide the connection plate to the bottom, and attach M3 screw
as shown. (Use the screw bundled to the package.)
MEMO: Press the right side of the connection plate.
16) After attaching the screw, pull the connection plate toward you.
MEMO: When holding the finisher, hold the front frame side
and the rear frame side.
and the rear frame side.
17) Insert the finisher along the connection plate rail from the left
side of the machine until it locks.
MX-M264U MX-FN23 (FINISHER) 7 – 4
18) Press the finisher from the front to slide to the rear together
with the connection plate.
19) Fix the connection plate from the front with the M3 screw which
are packed with the finisher.
20) Install the finisher connection cabinet from the left. (A hook
pawl is provided on the back. Be careful not to float.)
21) Install the finisher front cabinet lower with screw. (First attach
the A screw.)
A: M3 round-head screw
Use the screw which was removed from the FIN connection
unit.
B: M4 P tight screw
Use the screws which were removed from the paper exit tray
of the machine.
A: M3 round-head screw
Use the screw which was removed from the FIN connection
unit.
B: M4 P tight screw
Use the screws which were removed from the paper exit tray
of the machine.
22) Install the left cabinet to the original position.
23) Install the finisher front cover from the left side by sliding, and
fix the center of the fulcrum point with the resin clip.
24) Install the paper holding arm.
25) Close the finisher front cover and the machine front cover.
A
B
B
B
MX-M264U MX-FN23 (FINISHER) 7 – 5
26) Connect the machine connection connector.
Non LPS
Do not connect to devices other than specified peripheral
devices of our company.
Do not connect to devices other than specified peripheral
devices of our company.
27) Attach the staple position label to the document feed unit.
MX-M264U MX-TE10 (EXIT TRAY UNIT) 8 – 1
MX-M264U
Service Manual
[8] MX-TE10 (EXIT TRAY UNIT)
1. Parts included
2. Installation
NOTE: Turn off the main switch of the machine and then remove
the power plug of the machine from the outlet.
1)
Remove two EPE cushions.
2)
Remove five screws and remove the rear cabinet.
3)
Remove two screws and remove the right cabinet unit.
NOTE: One of the removed screws is used in the step 6).
4)
Insert the harness of the right paper exit unit to the hole of the
second paper exit.
second paper exit.
NOTE: Wire the harness to the upper of the rib.
If wiring it to the under of the rib, the harness may
come into contact with the gear.
come into contact with the gear.
5)
Insert the pawl of the right paper exit unit to the oval hole of the
frame of the main unit.
Insert the positioning boss of the main unit to the round hole in
lower side.
frame of the main unit.
Insert the positioning boss of the main unit to the round hole in
lower side.
6)
When tightening the screw, tighten in the sequence of (1), (2),
(3) and (4).
(3) and (4).
Paper exit unit
Paper exit tray
Paper holding arm
Harness cover OP
Screw (M3 x 4)
Paper exit
right cover
Right paper
exit actuator
Screw (M4 x 10)
Screw (M3 x 8)
2
1
1
1
Rib
Gear
3
2
1
4
Click on the first or last page to see other MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) service manuals if exist.