Sharp MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) Service Manual ▷ View online
MX-M264U Transit, Installation (using) environment, Note - ii
Operational environment
Temperature: 10 to 35
Temperature: 10 to 35
C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
(2) Contaminates
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.
jam, resulting in a shortened lifetime.
(3) Direct sunlight
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
the machine may be discolored and abnormal copies may be pro-
duced.
(4) Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam-
age by static electricity.
• When in transit or storing, put the parts in an anti-static bag or an
observe the following precautions in order to prevent against dam-
age by static electricity.
• When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
• When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:
• Put an earth band to your arm, and connect it to the machine.
• Put an earth band to your arm, and connect it to the machine.
• When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
85%
Humidity㧔RH㧕
60%
20%
(50F)
(86F)
(95F)
MX-M264U Transit, Installation (using) environment, Note - iii
G. Note for proper drum, developing and fusing
unit handling
When handling the OPC drum and developing units, observe the
following items.
Drum unit
• To prevent damage to the OPC drum, avoid working on the drum
following items.
Drum unit
• To prevent damage to the OPC drum, avoid working on the drum
unit in high intensity light areas.
• When the OPC drum is removed from the machine, cover it with
light blocking material. (When using paper, use about 10 sheets
of paper to cover it.)
of paper to cover it.)
• Be careful not to attach fingerprints, oil, grease, or other foreign
material on the OPC drum surface.
Developing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the developing unit.
Fusing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the fusing roller.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
copy and print image quality.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Use care not to exert vibrations or shocks to the machine when in
transit.
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Use care not to exert vibrations or shocks to the machine when in
transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
ronment.
No.
Content
Method
1
Implements, facility,
and man power
and man power
Use a forklift. (If no forklift is available,
manpower of two persons is required.)
manpower of two persons is required.)
2
Delivery
Transit must be made in packed condition.
MX-M264U CONFIGURATION 1 – 1
MX-M264U
Service Manual
[1] CONFIGURATION
1. System diagram
-8
-.-.-.
-8
-5-5-5
$)')4!,
-8
&.
&).)3(%2
-8
42
*/"
-8
4%
%8)4
-8
0+
03
-8
0&
"!2#/$%
-8
0"
02).4%2
-8
&8
&!#3)-),%
!2
35
34!-0
-8
&2&25
$!4!
-8
&78
).4%2.%4
-8
.38
.%47/2+
-8
($
(!2$
-8
53
3(!20$%3+
-8
5.(!
3HARP
-8
+"
+%9"/!2$
-8
538
3(!20$%3+
-8
538
3(!20$%3+
-8
53
3(!20$%3+
-8
53!
3(!20$%3+
-8
!-8
!00,)#!4)/.
).4%'2!4)/.
).4%'2!4)/.
-8
!-8
!00,)#!4)/.
#/--5.)#!4)/.
#/--5.)#!4)/.
-8
!-8
%84%2.!,
-8
3#8
34!0,%
!2
36
34!-0
-8
5.!
3HARP
-8
5.!
3HARP
-8
5.!
3HARP
-8
5.!
3HARP
-8
20
2%6%23).'
-8
62
$/#5-%.4
-8
$%
3(%%4 0!0%2
$2!7%2
$2!7%2
-8
$%
X 3(%%4 0!0%2
$2!7 %2
$2!7 %2
-8
$3
()'( 34!.$
-8
$3
,/7
-8
-.6-.6
$)')4!,
-8
($
(!2$
-8
$%
3(%%4 0!0%2
$2!7%2FOR
$2!7%2FOR
-8
-.2-.2-.2
1 Å
2013.8.23
1
2
‘13/Oct
2
MX-M264U CONFIGURATION 1 – 2
2. Option list
STD: Standard equipment
OPT: Installable option
*1: The FINISHER is required.
*2: Cannot be installed the EXIT TRAY UNIT and the FINISHER concurrently.
*3: Cannot be installed the JOB SEPARATOR concurrently.
*4: PRINTER EXPANSION KIT is required.
*5: HARD DISK EXPANSION KIT is required.
*6: APPLICATION COMMUNICATION MODULE is required.
*7: 500 Sheet Paper Drawer (for tray2:MX-DE24) is required for 1 tray model.
Model name
Name
MX-M264U
MX-M314U
MX-M354U
MX-M314U
MX-M354U
MX-M264N
MX-M314N
MX-M354N
MX-M314N
MX-M354N
MX-M264NR
MX-M314NR
MX-M354NR
MX-M314NR
MX-M354NR
MX-M264NV
MX-M314NV
MX-M314NV
Rema
rks
Document
feed system
feed system
MX-RP15
REVERSING SINGLE PASS FEEDER
OPT
STD
STD
STD
MX-VR11
DOCUMENT COVER
OPT
---
---
---
Paper feed
system
system
MX-DE17
500 SHEET PAPER DRAWER
OPT
OPT
OPT
OPT
MX-DE18
2x500 SHEET PAPER DRAWER
OPT
OPT
OPT
OPT
MX-DE24
500 SHEET PAPER DRAWER
STD
STD
STD
OPT*7
MX-DS16
LOW STAND
OPT
OPT
OPT
OPT
MX-DS17
HIGH STAND
OPT
OPT
OPT
OPT
Paper exit
system
system
MX-TE10
EXIT TRAY UNIT
OPT
OPT
OPT
OPT
*1
MX-TR11
JOB SEPARATOR
OPT
OPT
OPT
OPT
*2
MX-FN23
FINISHER
OPT
OPT
OPT
OPT
*3
Printer expan-
sion
sion
MX-PB15
PRINTER EXPANSION KIT
OPT
STD
STD
STD
MX-PK11
PS3 EXPANSION KIT
OPT
OPT
OPT
OPT
*4
MX-PF10
BARCODE FONT KIT
OPT
OPT
OPT
OPT
*4
Image send
expansion
expansion
MX-NSX1
NETWORK SCANNER EXPANSION KIT
OPT
STD
STD
STD
MX-FX11
FACSIMILE EXPANSION KIT
OPT
OPT
OPT
OPT
MX-FWX1
INTERNET FAX EXPANSION KIT
OPT
OPT
OPT
OPT
*5
AR-SU1
STAMP UNIT
OPT
OPT
OPT
OPT
Authentica-
tion/Security
tion/Security
MX-FR37/37U
DATA SECURITY KIT
OPT
OPT
---
---
*5
Application/
Solution
Solution
MX-USX1
SHARPDESK 1 L ２ ＲCENSE KIT
OPT
OPT
OPT
OPT
MX-USX5
SHARPDESK 5 LICENSE KIT
OPT
OPT
OPT
OPT
MX-US10
SHARPDESK 10 LICENSE KIT
OPT
OPT
OPT
OPT
MX-US50
SHARPDESK 50 LICENSE KIT
OPT
OPT
OPT
OPT
MX-USA0
SHARPDESK 100 LICENSE KIT
OPT
OPT
OPT
OPT
MX-UN01A
Sharp OSA Network Scanner Tool 1 License Kit
OPT
OPT
OPT
OPT
*6
MX-UN05A
Sharp OSA Network Scanner Tool 5 License Kit
OPT
OPT
OPT
OPT
*6
MX-UN10A
Sharp OSA Network Scanner Tool 10 License Kit
OPT
OPT
OPT
OPT
*6
MX-UN50A
Sharp OSA Network Scanner Tool 50 License Kit
OPT
OPT
OPT
OPT
*6
MX-UN1HA
Sharp OSA Network Scanner Tool 100 License Kit
OPT
OPT
OPT
OPT
*6
MX-AMX1
APPLICATION INTEGRATION MODULE
OPT
OPT
OPT
OPT
*5
MX-AMX2
APPLICATION COMMUNICATION MODULE
OPT
OPT
OPT
OPT
*5
MX-AMX3
EXTERNAL ACCOUNT MODULE
OPT
OPT
OPT
OPT
*5
Service
MX-SCX1
STAPLE CARTRIDGE
OPT
OPT
OPT
OPT
AR-SV1
STAMP CARTRIDGE
OPT
OPT
OPT
OPT
Other
MX-HD12
HARD DISK EXPANSION KIT
OPT
OPT
OPT
OPT
MX-HD12R
HARD DISK EXPANSION KIT
---
---
OPT
---
MX-HD13
HARD DISK EXPANSION KIT
---
---
---
OPT
MX-KB14
KEYBOARD
---
---
---
OPT
1
1
2
‘13/Oct
2
Click on the first or last page to see other MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) service manuals if exist.