Sharp MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) Service Manual ▷ View online
MX-M264U MX-DS16/DS17 (LOW STAND/HIGH STAND) 6 – 1
MX-M264U
Service Manual
[6] MX-DS16/DS17 (LOW STAND/HIGH STAND)
1. Unpacking
Unpack the package, and check to confirm that all the parts are
provided.
provided.
Packed parts
2. Installation
1)
Attach the adjusters.
Attach the front adjusters (2 pcs.) as shown in the figure below.
Attach the front adjusters (2 pcs.) as shown in the figure below.
2)
Attach the adjuster covers.
Put the desk on the floor in the normal state, and open the
door.
Slide the adjuster covers (2 pcs.) as shown in the figure below
and attach them. Then, close the door.
Put the desk on the floor in the normal state, and open the
door.
Slide the adjuster covers (2 pcs.) as shown in the figure below
and attach them. Then, close the door.
3)
Remove the paper tray.
Pull out the paper feed unit tray from the copier until it stops.
Lift it and remove it from the copier.
Pull out the paper feed unit tray from the copier until it stops.
Lift it and remove it from the copier.
Machine stand
Packed parts add
MX-DS16
MX-DS17
Front adjusters: 2 pcs.
Adjuster covers: 2 pcs.
Copier connecting fixtures:
2 pcs.
2 pcs.
Screws (S tight):
2 pcs.
2 pcs.
Screws (P tight):
4 pcs.
4 pcs.
( 110)
Front
adjuster
adjuster
Front
adjuster
adjuster
Rear side
Front side
Screw the adjusters into
the hole so that the adjuster
tips do not extend out from
the hole.
the hole so that the adjuster
tips do not extend out from
the hole.
( 110)
( 110)
Front side
Adjuster covers
Adjuster covers
Front side
MX-DS17
MX-DS16
MX-M264U MX-DS16/DS17 (LOW STAND/HIGH STAND) 6 – 2
4)
Put the copier (or the paper feed unit) on the desk.
Insert the positioning pins (2 pcs.) of the desk into the position-
ing holes of the copier (or the paper feed unit).
At that time, be careful not to break the fixtures on the desk
side.
Insert the positioning pins (2 pcs.) of the desk into the position-
ing holes of the copier (or the paper feed unit).
At that time, be careful not to break the fixtures on the desk
side.
5)
Connect the copier with the desk.
Connect the copier with the desk with two screws (P tight,
packed together with the copier) and the fixture.
Connect the copier with the desk with two screws (P tight,
packed together with the copier) and the fixture.
6)
Remove the two screws, and remove the rear cover.
7)
Connect the copier (or the paper feed unit) and the desk with
two screws (P tight) and two screws (S tight) packed together
with the copier. When connecting, be careful of the direction of
the connecting fixture of the copier.
two screws (P tight) and two screws (S tight) packed together
with the copier. When connecting, be careful of the direction of
the connecting fixture of the copier.
8)
Attach the rear cover, and fix it with the two screws.
9)
Install the paper tray.
Install the paper tray to the original position.
Install the paper tray to the original position.
ུఘ
Positioning pin
Copier
Be careful not to hit.
Machine stand
Fixture
Positioning pin
Front side
Screws (P tight)
Screws (P tight)
Back side
Copier
connecting
fixture
connecting
fixture
Screws (P tight)
Screws (P tight)
Screws (S tight)
Copier
connecting
fixture
connecting
fixture
Screws (S tight)
MX-M264U MX-FN23 (FINISHER) 7 – 1
MX-M264U
Service Manual
[7] MX-FN23 (FINISHER)
1. Unpacking
MEMO: When removing the finisher, put your hand beneath the
unit and lift it up as shown below.
unit and lift it up as shown below.
Check to confirm that all the packed parts are provided.
2. Installation
NOTE: Turn off the main switch of the machine and then remove
the power plug of the machine from the outlet.
1)
Open the front cover.
2)
Remove the screws, and remove the left cabinet.
3)
Remove the screw which are fixing the paper exit tray.
Remove the paper exit tray by using care for the tray paper
presence detection harness which is connected to the back
side of the paper exit tray.
Remove the paper exit tray by using care for the tray paper
presence detection harness which is connected to the back
side of the paper exit tray.
FIN connection unit
FIN front cover
Second paper exit unit
Paper holding arm
Rail dummy cover
M3 x 8 S tight bind
(4 pcs.)
M3 x 10 S tight bind
(4 pcs.)
Resin grip
Staple position label
MX-M264U MX-FN23 (FINISHER) 7 – 2
4)
Insert the tray paper presence detection harness into the
dummy connector on the fan duct.
dummy connector on the fan duct.
5)
Disengage the pawls in the sequence of (1) and (2) and
remove the paper exit dummy cover.
remove the paper exit dummy cover.
6)
Remove the screw and remove the rear cabinet.
7)
Remove the screw, and remove the right cabinet lever cover.
8)
Open the manual feed tray and the right door.
Remove the two screws, and remove the right cabinet.
Remove the two screws, and remove the right cabinet.
9)
Pass the harness (packed together with the unit) of the second
paper exit unit though inside of the frame plate as shown in the
figure.
Install the second paper exit unit to the machine, and fix it with
the four M4 S tight screws which are packed together with the
finisher. Connect the connector of the harness.
paper exit unit though inside of the frame plate as shown in the
figure.
Install the second paper exit unit to the machine, and fix it with
the four M4 S tight screws which are packed together with the
finisher. Connect the connector of the harness.
10) Install the right cabinet to the original position, and fix it with
two screws.
Close the right door and the manual paper feed tray.
Close the right door and the manual paper feed tray.
1
2
1
1
2
Click on the first or last page to see other MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man6) service manuals if exist.