Sharp MX-FXX3 Service Manual ▷ View online
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 15
• 7.0/8.5 Inch LCD model
66-11
Purpose
Operation test/Check
Function (Purpose) Used to send the selected signal at 300bps
to the line and the speaker. (Send level:
Max.)
Max.)
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-11, the following
screen is displayed. (Default, left upper setting)
screen is displayed. (Default, left upper setting)
2)
When a button of a sound message to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
3)
When [EXECUTE] button is pressed, it is highlighted and a
sound message is sent.
sound message is sent.
4)
To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
<300bps send signal table>
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-12
Purpose
Operation test/Check
Function (Purpose) Used to send the selected signal at 300bps
to the line and the speaker. (Send level:
Soft SW setting)
* For the kings of send signals at 300bps,
refer to SIM66-11, 300bps send signal
table.
Soft SW setting)
* For the kings of send signals at 300bps,
refer to SIM66-11, 300bps send signal
table.
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-12, the following
screen is displayed. (Default, left upper setting)
screen is displayed. (Default, left upper setting)
2)
When a button of a sound message to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
3)
When [EXECUTE] button is pressed, it is highlighted and a
sound message is sent.
sound message is sent.
4)
To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
NO SIGNAL
11111
11110
00000
010101
00001
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
,0$*(0(025<&/($5
(;(&87(
$5(<28685("
<(6
12
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
ESV6,*1$/287387/(9(/0$;
7(67
126,*1$/
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
ESV6,*1$/287387/(9(/0$;
(;(&87(
126,*1$/
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
ESV6,*1$/28738762)76:
7(67
126,*1$/
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
ESV6,*1$/28738762)76:
(;(&87(
126,*1$/
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 16
66-13
Purpose
Setting
Function (Purpose) Used to register dial numbers for SIM66-
14/15/16, Dial test. (Up to 20 digits can be
registered.)
registered.)
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-13, the following
screen is displayed.
* The number saved in the memory is displayed in the column
screen is displayed.
* The number saved in the memory is displayed in the column
of [PRESENT:]. (If there is no data, [-------] is displayed.)
2)
Enter a number with 10-key.
The entered number is displayed in the column of [NEW:].
After entering 20 digits, 10-key is disabled (no response). Only
[C] key is enabled. (10-key [0] to [9], [*], [#], [C] key (back by
one digit))
The entered number is displayed in the column of [NEW:].
After entering 20 digits, 10-key is disabled (no response). Only
[C] key is enabled. (10-key [0] to [9], [*], [#], [C] key (back by
one digit))
3)
When [SET] key is pressed after completion of entry, the
entered number is displayed (registered) in the column of
[PRESENT:]. The column of [NEW:] becomes blank.
* If the "NEW:" column is blank, SET is inactive. When a value
entered number is displayed (registered) in the column of
[PRESENT:]. The column of [NEW:] becomes blank.
* If the "NEW:" column is blank, SET is inactive. When a value
is entered to the "NEW:" column, it becomes active.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-14
Purpose
Adjustment
Function (Purpose) Used to execute the dial pulse (10PPS)
send test and to adjust the make time.
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-14, the following
screen is displayed.
* Enter the make time (0 to 15) with 10-key and press [OK]
screen is displayed.
* Enter the make time (0 to 15) with 10-key and press [OK]
button, and the entered make time is temporality saved.
* Enter the make time (0 to 15) with 10-key and press [EXE-
CUTE] button instead of [OK] button, and [EXECUTE] but-
ton is highlighted and the dial pulse is sent from the line in
the set make time.
ton is highlighted and the dial pulse is sent from the line in
the set make time.
2)
When [EXECUTE] button is pressed, it is highlighted and the
dial pulse is sent from the line in the set make time.
* The dial pulse in this example is up to 20 digits registered
dial pulse is sent from the line in the set make time.
* The dial pulse in this example is up to 20 digits registered
with SIM66-13.
3)
To end the dial test, press [EXCUTE] button again. The button
returns to the normal display and the test is terminated.
Also when dialing the number is completed, [EXECUTE] but-
ton returns to the normal display and the test is terminated.
returns to the normal display and the test is terminated.
Also when dialing the number is completed, [EXECUTE] but-
ton returns to the normal display and the test is terminated.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
',$/7(67180%(5ǂ6(77,1*
7(67
6(7
35(6(17
1(:
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
',$/7(67180%(5ǂ6(77,1*
35(6(17˖
ǂǂ1(:˖
ǂǂ1(:˖
6(7
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$˖
˷̚˹
',$/7(67336
˖0$.(7,0(>PV@
$˖
7(67
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
',$/7(67336
$˖
˷̚˹
˖0$.(7,0(>PV@
$˖
2.
(;(&87(
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 17
66-15
Purpose
Adjustment
Function (Purpose) Used to execute the dial pulse (20PPS)
send test and to adjust the make time.
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-15, the following
screen is displayed.
* Enter the make time (0 to 15) with 10-key and press [OK]
screen is displayed.
* Enter the make time (0 to 15) with 10-key and press [OK]
button, and the entered make time is temporality saved.
* Enter the make time (0 to 15) with 10-key and press [EXE-
CUTE] button instead of [OK] button, and [EXECUTE] but-
ton is highlighted and the dial pulse is sent from the line in
the set make time.
ton is highlighted and the dial pulse is sent from the line in
the set make time.
2)
When [EXECUTE] button is pressed, it is highlighted and the
dial pulse is sent from the line in the set make time.
* The dial pulse in this example is up to 20 digits registered
dial pulse is sent from the line in the set make time.
* The dial pulse in this example is up to 20 digits registered
with SIM66-13.
3)
To end the dial test, press [EXCUTE] button again. The button
returns to the normal display and the test is terminated.
Also when dialing the number is completed, [EXECUTE] but-
ton returns to the normal display and the test is terminated.
returns to the normal display and the test is terminated.
Also when dialing the number is completed, [EXECUTE] but-
ton returns to the normal display and the test is terminated.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-16
Purpose
Adjustment
Function (Purpose) Used to execute the DTFM signal send test
and to adjust the send level.
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-16, the following
screen is displayed.
* Item A (High group frequency) and item B (High-Low group
screen is displayed.
* Item A (High group frequency) and item B (High-Low group
frequency) are selected with [
] [] buttons. When the
selected item is the top (last) item, [
] [] buttons gray out.
(The highlighted section of the set value is switched and dis-
played on the set setting area.)
When [
played on the set setting area.)
When [
] [] buttons gray out, they are disabled.
* Enter the High group or High - Low group (0 to 15) with 10-
key and press [OK] button. The set sign send level is tempo-
rality saved.
rality saved.
* Enter the single send level (0 to 15) with 10-key and press
[EXECUTE] button instead of [OK] button, and [EXECUTE]
button is highlighted and the dial pulse is sent from the line
by the setting of high group or low group.
button is highlighted and the dial pulse is sent from the line
by the setting of high group or low group.
2)
When [EXECUTE] button is pressed, it is highlighted and the
dial pulse signal is sent from the line by the setting of high/low
group of the signal send level.
dial pulse signal is sent from the line by the setting of high/low
group of the signal send level.
3)
To terminate the dial test, press [EXECUTE] button. The button
returns to the normal display and the test is terminated.
When dialing the dial number is completed, [EXECUTE] button
returns to the normal display and the test is terminated.
returns to the normal display and the test is terminated.
When dialing the dial number is completed, [EXECUTE] button
returns to the normal display and the test is terminated.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$˖
˷̚˹
',$/7(67336
˖0$.(7,0(>PV@
$˖
7(67
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
',$/7(67336
$˖
˷̚˹
˖0$.(7,0(>PV@
$˖
2.
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$˖
˷̚˹
',$/7(67'70)
˖+,*+G%
$˖
˖+,*+/2:
%˖
7(67
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
',$/7(67'70)
$˖
˷̚˹
˖+,*+G%
$˖
˖+,*+/2:
%˖
2.
(;(&87(
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 18
66-17
Purpose
Operation test/Check
Function (Purpose) Used to send the DTMF signal to the line
and the speaker. (Send level: Max.)
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-17, the following
screen is displayed. (Default, left upper selected)
screen is displayed. (Default, left upper selected)
2)
When a button of a send signal is selected, it is highlighted and
the previously set button returns to the normal display.
* Only one kind of signal to be sent can be selected.
the previously set button returns to the normal display.
* Only one kind of signal to be sent can be selected.
3)
When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
* When another signal send button is pressed during sending
nals are sent.
* When another signal send button is pressed during sending
signals, the send signal can be changed.
4)
To stop signal sending:
When [EXECUTE] button is pressed, it returns to the normal
display and signal sending is interrupted.
When [EXECUTE] button is pressed, it returns to the normal
display and signal sending is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-18
Purpose
Operation test/Check
Function (Purpose) Used to send the DTMF signal to the line
and the speaker. (Send level: Soft SW set-
ting)
ting)
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-18, the following
screen is displayed.
screen is displayed.
2)
When a button of a send signal is selected, it is highlighted and
the previously set button returns to the normal display.
the previously set button returns to the normal display.
3)
When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
* When another signal send button is pressed during sending
nals are sent.
* When another signal send button is pressed during sending
signals, the send signal can be changed.
4)
To stop signal sending:
When [EXECUTE] button is pressed, it returns to the normal
display and signal sending is interrupted.
When [EXECUTE] button is pressed, it returns to the normal
display and signal sending is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-21
Purpose
Check
Function (Purpose) Used to print the selected items (various
registration information, communication
management information, file management
information, system error, protocol moni-
tor).
management information, file management
information, system error, protocol moni-
tor).
Section
FAX
Operation/Procedure
1)
1)
When an item button to be printed is selected, it is highlighted
and the previously set button returns to the normal display.
(Default select: Left upper)
* Only one item can be selected.
and the previously set button returns to the normal display.
(Default select: Left upper)
* Only one item can be selected.
2)
Press [EXECUTE] button.
[EXECUTE] button is highlighted and printing is started.
* During printing an item, [EXECUTE] and the print item but-
[EXECUTE] button is highlighted and printing is started.
* During printing an item, [EXECUTE] and the print item but-
ton are highlighted.
3)
After completion of printing, [EXECUTE] button returns to the
normal display.
normal display.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key is
pressed during printing, the operation is interrupted.
<FAX information print content table>
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
'70)6,*1$/287387/(9(/0$;
7(67
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'70)6,*1$/287387/(9(/0$;
(;(&87(
REGISTERED
MANAGEMENT
FILE MANAGEMENT
SYSTEM ERROR LINE 1
PROTOCOL LINE 1
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
'70)6,*1$/28738762)76:
7(67
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'70)6,*1$/28738762)76:
(;(&87(
Click on the first or last page to see other MX-FXX3 service manuals if exist.