Sharp MX-FXX3 Service Manual ▷ View online
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 11
Country code list screen
• 4.3 Inch LCD model
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-3
Purpose
Operation test/Check
Function (Purpose) Used to execute the read/write check of
EEPROM on the MODEM controller,
SDRAM, SRAM on the MFP controller, and
flash ROM, and to display the results.
SDRAM, SRAM on the MFP controller, and
flash ROM, and to display the results.
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-03, the following
screen is displayed.
* Use [
screen is displayed.
* Use [
] [] buttons to select the country select page. (The
highlighted section of the set value is switched and dis-
played on the set setting area.)
When [
played on the set setting area.)
When [
] [] buttons gray out, they are disabled.
2)
When the memory check item button is selected, the display is
shifted to the memory check screen.
* Only one memory check item can be selected.
shifted to the memory check screen.
* Only one memory check item can be selected.
3)
When [EXECUTE] button is pressed, it is highlighted and the
memory check of the selected item is started.
* When [EXECUTE] button is pressed again during memory
memory check of the selected item is started.
* When [EXECUTE] button is pressed again during memory
check, the operation is interrupted. (The display shows the
status immediately before pressing [EXECUTE] button.)
When [EXECUTE] button is pressed after interrupting the
operation, memory check is resumed.
status immediately before pressing [EXECUTE] button.)
When [EXECUTE] button is pressed after interrupting the
operation, memory check is resumed.
4)
After completion of memory check, [EXECUTE] button returns
to the normal display and the result of memory check is dis-
played.
* For the memory which is not installed, [NO CHECK] is dis-
to the normal display and the result of memory check is dis-
played.
* For the memory which is not installed, [NO CHECK] is dis-
played.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display
* When [SYSTEM SETTINGS] key is pressed, the display
returns to the sub number entry screen.
* In the case of [REPEAT] check, the following display is made for
every execution.
CHECKING 0001
CHECKING 0002
CHECKING 0003
:
:
The number of times is displayed in 4-digit decimal numbers.
When the number exceeds 9999, it becomes 0000
Check is repeated until [EXECUTE] is pressed or [NG] occurs.
CHECKING 0001
CHECKING 0002
CHECKING 0003
:
:
The number of times is displayed in 4-digit decimal numbers.
When the number exceeds 9999, it becomes 0000
Check is repeated until [EXECUTE] is pressed or [NG] occurs.
Memory check status
Check item
The number in < > indicates the line.
• 4.3 Inch LCD model
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
)$;62)76:&/($5
-$3$1˖86$˖
$8675$/,$˖8.˖
)5$1&(˖*(50$1<˖
6:('(1˖1(:=($/$1'˖
7(67
%$&.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)$;62)76:&/($5
%$&.
-$3$1˖86$˖
$8675$/,$˖8.˖
)5$1&(˖*(50$1<˖
6:('(1˖1(:=($/$1'˖
&+,1$˖6,1*$325(˖
7:˖0,''/($1'1($5($6˖
6/29$.,$˖27+(5˖
),1/$1'˖125:$<˖
'(10$5.ǂ˖1(7+(5/$1'6˖
,7$/<˖6:,7=(5$1'˖
$8675,$˖,1'21(6,$˖
7+$,/$1'˖0$/$<6,$˖
NO CHECK
No check
CHECKING
During checking
OK
Check complete OK
NG A##
Check complete NG
Error occurring address or data
line is displayed for each item.
line is displayed for each item.
Check memory item
Remark
1
All Memory Device Check (once)
All the items are checked
once.
once.
2
MFP SRAM (once)
Check only once
3
MFP SRAM (repeat)
Repeat check
4
MFP FLASH + OP.FLASH (once)
Check only once
5
MFP FLASH + OP.FLASH (repeat)
Repeat check
6
MODEM EEPROM <1> (once)
Check only once in LINE1
7
MODEM EEPROM <1> (repeat)
Repeat check in LINE1
8
MODEM SDRAM <1> (once)
Check only once in LINE1
9
MODEM SDRAM<1>(repeat)
Repeat check in LINE1
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
)$;3:%0(025<&+(&.
7(67
$OO0HP'HY&KHFNRQFH
0)365$0UHSHDW
0)323)/$6+UHSHDW
02'(0((3520!UHSHDW
0)365$0RQFH
0)323)/$6+RQFH
02'(0((3520!RQFH
02'(06'5$0!RQFH
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)$;3:%0(025<&+(&.
$//0HPRU\'HYLFH&KHFNRQFH
0)365$0RQFH
0)365$0UHSHDW
0)3)/$6+23)/$6+RQFH
0)3)/$6+23)/$6+UHSHDW
02'(0((3520!RQFH
02'(0((3520!UHSHDW
02'(06'5$0!RQFH
02'(06'5$0!UHSHDW
02'(0((3520!RQFH
02'(0((3520!UHSHDW
02'(06'5$0!RQFH
02'(06'5$0!UHSHDW
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 12
66-4
Purpose
Operation test/Check
Function (Purpose) Used to send the selected signals to the
line and the main unit speaker. (Send level:
max.)
max.)
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-04, the screen on the
right is displayed. (Default, left upper selected.)
* Use [
right is displayed. (Default, left upper selected.)
* Use [
] [] buttons to switch the send mode select page.
When the selected item is the top (last) item, [
] [] buttons
gray out. (The highlighted section of the set value is
switched and displayed on the set setting area.)
When [
switched and displayed on the set setting area.)
When [
] [] buttons gray out, they are disabled.
2)
When a button of a signal to be sent is selected, it is high-
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.
3)
When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
nals are sent.
4)
To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
<Signal send table>
Page1
Page2
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-5
Purpose
Operation test/Check
Function (Purpose) Used to send the selected signal to the line
and the main unit speaker. (Send level: Soft
SW setting) (For the kinds of send signals,
refer to PART1 and PART2 of SIM66-04.)
SW setting) (For the kinds of send signals,
refer to PART1 and PART2 of SIM66-04.)
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-05, the following
screen is displayed. (Default, left upper selected)
* Use [
screen is displayed. (Default, left upper selected)
* Use [
] [] buttons to switch the send mode select page.
When the selected item is the top (last) item, [
] [] buttons
gray out. (The highlighted section of the set value is
switched and displayed on the set setting area.)
When [
switched and displayed on the set setting area.)
When [
] [] buttons gray out, they are disabled.
2)
When a button of a signal to be sent is selected, it is high-
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.
lighted and the previously set button is shifted to the normal
display.
* Only one signal to be sent can be selected.
3)
When [EXECUTE] button is pressed, it is highlighted and sig-
nals are sent.
nals are sent.
4)
To end signal send:
* When [EXECUTE] button is pressed, it is highlighted and
* When [EXECUTE] button is pressed, it is highlighted and
signal send is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display
* When [SYSTEM SETTINGS] key is pressed, the display
returns to the sub number entry screen.
• 4.3 Inch LCD model
NOSIGNAL
33.6 V34
31.2 V34
28.8 V34
26.4 V34
24.0 V34
21.6 V34
19.2 V34
16.8 V34
14.4 V34
12.0 V34
9.6 V34
7.2 V34
4.8 V34
2.4 V34
14.4 V33
12.0 V33
14.4 V17
12.0 V17
9.6 V17
7.2 V17
9.6 V29
7.2 V29
4.8 V27t
2.4 V27t
0.3 FLG
CED 2100
CNG 1100
0.3 V21
ANSam
RINGER
No RBT
DP MAKE
DP BRK
NO MSG
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
6,*1$/287387&+(&./(9(/0$;
7(67
126,*1$/
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6,*1$/287387&+(&./(9(/0$;
(;(&87(
126,*1$/
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9W
9
9W
)/*
&1*
&('
9
$96DP
1R5%7
5,1*(5
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
6,*1$/287387&+(&.62)76:
7(67
126,*1$/
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
(;(&87(
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 13
• 7.0/8.5 Inch LCD model
66-6
Purpose
Data output/Check
Function (Purpose) Used to print the confidential registration
check table (BOX NO., BOX name, pass-
code. (If there is no confidential registra-
tion, no print is made.)
code. (If there is no confidential registra-
tion, no print is made.)
Section
FAX
Operation/Procedure
1)
1)
When [EXECUTE] button is pressed, it is highlighted and the
confidential checkable is printed.
* If there is no confidential registration, no print is made even
confidential checkable is printed.
* If there is no confidential registration, no print is made even
though [EXECUTE] key is pressed.
2)
After completion of printing, [EXECUTE] button returns to the
normal display.
normal display.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key is
pressed during printing, the operation is interrupted.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-7
Purpose
Data output/Check
Function (Purpose) Used to output all image data saved in the
image memory. (Confidential data are also
outputted.)
outputted.)
Section
FAX
Operation/Procedure
1)
1)
When [EXECUTE] button is pressed, it is highlighted and all
image data saved in the image memory are outputted.
* The confidential data are also outputted.
image data saved in the image memory are outputted.
* The confidential data are also outputted.
After completion of printing, the image data are not cleared.
* If there is no image memory, no print is made though [EXE-
CUTE] button is pressed.
2)
After completion of printing, [EXECUTE] button returns to the
normal display.
normal display.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
* When [C], [CA], [SYSTEM SETTINGS], or [EXECUTE] key is
pressed during printing, the operation is interrupted.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-8
Purpose
Operation test/Check
Function (Purpose) Used to send the selected sound mes-
sages to the line and the speaker. (Send
level: Max.)
level: Max.)
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-08, the following
screen is displayed. (Default, left upper selected)
screen is displayed. (Default, left upper selected)
2)
When the sound message button to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
* When [EXECUTE] button is pressed, it is highlighted and a
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
* When [EXECUTE] button is pressed, it is highlighted and a
sound message is sent.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6,*1$/287387&+(&.62)76:
(;(&87(
126,*1$/
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9W
9
9W
)/*
&1*
&('
9
$96DP
1R5%7
5,1*(5
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
3$66&2'(35,17287
7(67
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
3$66&2'(35,17287
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
,0$*(0(025<35,17287
7(67
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
,0$*(0(025<35,17287
(;(&87(
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 14
* When [EXECUTE] button is pressed, it is returns to the nor-
mal display and sending a sound message is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
<Sound message table>
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-9
Purpose
Operation test/Check
Function (Purpose) Used to send the selected sound message
to the line and the speaker. (Send level:
max.)
* For details of sound messages, refer to
the sound message table of SIM66-08.
max.)
* For details of sound messages, refer to
the sound message table of SIM66-08.
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-09, the following
screen is displayed. (Default, left upper setting)
screen is displayed. (Default, left upper setting)
2)
When a button of a sound message to be sent is selected, it is
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
highlighted and the previously set button returns to the normal
display.
* Only one sound message to be sent can be selected.
3)
When [EXECUTE] button is pressed, it is highlighted and a
sound message is sent.
sound message is sent.
4)
To end signal send:
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
When [EXECUTE] button is pressed, it is highlighted and sig-
nal send is interrupted.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66-10
Purpose
Data clear
Function (Purpose) Used to clear all image data saved in the
FAX image memory. (The confidential data
are also cleared.)
are also cleared.)
Section
FAX
Operation/Procedure
1)
1)
Press [EXECUTE] button.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.
[EXECUTE] button is highlighted and [YES] and [NO] buttons
become active.
2)
Press [YES] button.
The image memory is cleared. [YES] button is highlighted.
* When [NO] button is pressed, [EXECUTE] button returns to
The image memory is cleared. [YES] button is highlighted.
* When [NO] button is pressed, [EXECUTE] button returns to
the normal display and [YES] and [NO] buttons gray out.
* During clearing the image memory, [EXECUTE] and [YES]
buttons are highlighted.
The image memory can be cleared even if there is no image
data.
The image memory can be cleared even if there is no image
data.
3)
After completion of clearing, press [CA] key to reboot the
machine.
machine.
• 4.3 Inch LCD model
NONE (Mute)
PAUSE (Pause
melody)
melody)
MESSAGE1
(Message 1)
(Message 1)
MESSAGE2
(Message 2)
(Message 2)
MESSAGE3
(Message 3)
(Message 3)
MESSAGE4
(Message 4)
(Message 4)
MESSAGE5
(Massage 5)
(Massage 5)
MESSAGE6
(Message 6)
(Message 6)
ALARM (Alarm)
RINGER
(Ringing sound
(Speaker))
(Ringing sound
(Speaker))
EXT.TEL.RING
ER (External
telephone call)
ER (External
telephone call)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
0(66$*(287387&+(&./(9(/0$;
7(67
121(
0(66$*(
$/$50
0(66$*(
0(66$*(
(;77(/5
3$86(
0(66$*(
5,1*(5
0(66$*(
0(66$*(
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
0(66$*(287387&+(&./(9(/0$;
(;(&87(
121(
3$86(
0(66$*(
0(66$*(
0(66$*(
0(66$*(
0(66$*(
0(66$*(
$/$50
5,1*(5
(;77(/5,1*(5
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
0(66$*(287387&+(&.62)76:
7(67
121(
0(66$*(
$/$50
0(66$*(
0(66$*(
(;77(/5
3$86(
0(66$*(
5,1*(5
0(66$*(
0(66$*(
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
0(66$*(287387&+(&.62)76:
(;(&87(
121(
3$86(
0(66$*(
0(66$*(
0(66$*(
0(66$*(
0(66$*(
0(66$*(
$/$50
5,1*(5
(;77(/5,1*(5
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
,0$*(0(025<&/($5
7(67
(;(&87(
685("
<(6
12
Click on the first or last page to see other MX-FXX3 service manuals if exist.