Sharp MX-FXX3 Service Manual ▷ View online
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 7
46-44
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the FAX send image density.
(Ultra fine)
Section
Operation/Procedure
1)
1)
Set the original on the original table.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (For the 4.3 Inch LCD model, press the OSA
shortcut key.)
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
shortcut key.)
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
To check the adjustment density level of items A - L, set the docu-
ment and set the setting value of item M according to items A - L,
and press [EXECUTE] key.
ment and set the setting value of item M according to items A - L,
and press [EXECUTE] key.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
46-45
Purpose
Adjustment/Setup
Function (Purpose) Used to adjust the FAX send image density.
(600dpi).
Section
Operation/Procedure
1)
1)
Set the original on the original table.
2)
Enter the set value with 10-key.
3)
Press [OK] key. (For the 4.3 Inch LCD model, press the OSA
shortcut key.)
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
shortcut key.)
When [EXECUTE] key is pressed, the adjustment value is set
and the scanned document image is outputted.
Item/Display
Content
Setting
range
Default
value
A
AUTO
Ultra Fine/Auto
1 - 99
50
B
EXPOSURE1
Ultra Fine/Exposure
1
1
1 - 99
50
C
EXPOSURE2
Ultra Fine/Exposure
2
2
1 - 99
50
D
EXPOSURE3
Ultra Fine/Exposure
3
3
1 - 99
50
E
EXPOSURE4
Ultra Fine/Exposure
4
4
1 - 99
50
F
EXPOSURE5
Ultra Fine/Exposure
5
5
1 - 99
50
G
AUTO H_TONE
Ultra Fine/Auto/Half
tone
tone
1 - 99
50
H
EXPOSURE1 H_TONE
Ultra Fine/Exposure
1/Half tone
1/Half tone
1 - 99
50
I
EXPOSURE2 H_TONE
Ultra Fine/Exposure
2/Half tone
2/Half tone
1 - 99
50
J
EXPOSURE3 H_TONE
Ultra Fine/Exposure
3/Half tone
3/Half tone
1 - 99
50
K
EXPOSURE4 H_TONE
Ultra Fine/Exposure
4/Half tone
4/Half tone
1 - 99
50
L
EXPOSURE5 H_TONE
Ultra Fine/Exposure
5/Half tone
5/Half tone
1 - 99
50
M
EXECUTE
MODE
MODE
AUTO
Print
mode
mode
Ultra Fine/
Auto
Auto
1 -
12
12
1
1
(AUTO)
EXP1
Ultra Fine/
Exposure 1
Exposure 1
2
EXP2
Ultra Fine/
Exposure 2
Exposure 2
3
EXP3
Ultra Fine/
Exposure 3
Exposure 3
4
EXP4
Ultra Fine/
Exposure 4
Exposure 4
5
EXP5
Ultra Fine/
Exposure 5
Exposure 5
6
AUTO
H_TONE
H_TONE
Ultra Fine/
Auto/Half
tone
Auto/Half
tone
7
EXP1
H_TONE
H_TONE
Ultra Fine/
Exposure
1/Half tone
Exposure
1/Half tone
8
EXP2
H_TONE
H_TONE
Ultra Fine/
Exposure 2
/Half tone
Exposure 2
/Half tone
9
EXP3
H_TONE
H_TONE
Ultra Fine/
Exposure 3
/Half tone
Exposure 3
/Half tone
10
EXP4
H_TONE
H_TONE
Ultra Fine/
Exposure 4
/Half tone
Exposure 4
/Half tone
11
EXP5
H_TONE
H_TONE
Ultra Fine/
Exposure 5
/Half tone
Exposure 5
/Half tone
12
Item/Display
Content
Setting
range
Default
value
A
AUTO
600dpi/Auto 1
1 - 99
50
B
EXPOSURE1
600dpi/Exposure 1
1 - 99
50
C
EXPOSURE2
600dpi/Exposure 2
1 - 99
50
D
EXPOSURE3
600dpi/Exposure 3
1 - 99
50
E
EXPOSURE4
600dpi/Exposure 4
1 - 99
50
F
EXPOSURE5
600dpi/Exposure 5
1 - 99
50
G
AUTO H_TONE
600dpi/Auto
/Half tone 1
/Half tone 1
1 - 99
50
H
EXPOSURE1 H_TONE
600dpi/Exposure 1
/Half tone
/Half tone
1 - 99
50
I
EXPOSURE2 H_TONE
600dpi/Exposure 2
/Half tone
/Half tone
1 - 99
50
J
EXPOSURE3 H_TONE
600dpi/Exposure 3
/Half tone
/Half tone
1 - 99
50
K
EXPOSURE4 H_TONE
600dpi/Exposure 4
/Half tone
/Half tone
1 - 99
50
L
EXPOSURE5 H_TONE
600dpi/Exposure 5
/Half tone
/Half tone
1 - 99
50
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$˖
˷̚˹
(;(32685($'-8670(17)$;8/75$),1(
˖$872
$˖
˖(;32685(
%˖
˖(;32685(
&˖
˖(;32685(
'˖
7(67
(;(&87(
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 8
To check the adjustment density level of items A - L, set the docu-
ment and set the setting value of item M according to items A - L,
and press [EXECUTE] key.
• 4.3 Inch LCD model
ment and set the setting value of item M according to items A - L,
and press [EXECUTE] key.
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
50
50-27
Purpose
Adjustment
Function (Purpose) Used to perform the image loss adjustment
of scanned images in the FAX or image
send mode.
send mode.
Section
Operation/Procedure
1)
1)
Select a target adjustment mode.
2)
Select an adjustment target item with [
] [] key on the touch
panel.
3)
Enter the set value with 10-key.
4)
Press [OK] key. (For the 4.3 Inch LCD model, press the OSA
shortcut key.) (The set value is saved.)
shortcut key.) (The set value is saved.)
M
EXECUTE
MODE
MODE
AUTO
Print
mode
mode
600dpi/Auto
1 -
12
12
1
1
(AUTO)
EXP1
600dpi/
Exposure 1
Exposure 1
2
EXP2
600dpi/
Exposure 2
Exposure 2
3
EXP3
600dpi/
Exposure 3
Exposure 3
4
EXP4
600dpi/
Exposure 4
Exposure 4
5
EXP5
600dpi/
Exposure 5
Exposure 5
6
AUTO
H_TONE
H_TONE
600dpi/Auto/
Half tone
Half tone
7
EXP1
H_TONE
H_TONE
600dpi/
Exposure 1
/Half tone
Exposure 1
/Half tone
8
EXP2
H_TONE
H_TONE
600dpi/
Exposure 2
/Half tone
Exposure 2
/Half tone
9
EXP3
H_TONE
H_TONE
600dpi/
Exposure 3
/Half tone
Exposure 3
/Half tone
10
EXP4
H_TONE
H_TONE
600dpi/
Exposure 4
/Half tone
Exposure 4
/Half tone
11
EXP5
H_TONE
H_TONE
600dpi/
Exposure 5
/Half tone
Exposure 5
/Half tone
12
Item/Display
Content
Setting
range
Default
value
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$˖
˷̚˹
(;(32685($'-8670(17)$;'3,
˖$872
$˖
˖(;32685(
%˖
˖(;32685(
&˖
˖(;32685(
'˖
7(67
(;(&87(
Item/Display
Content
Setting
range
Default
value
FAX
send
send
A
Image
loss
amount
setting
OC
loss
amount
setting
OC
LEAD_EDGE
(OC)
(OC)
OC lead
edge
image loss
amount
setting
edge
image loss
amount
setting
0 - 100
30
(3mm)
B
FRONT
_REAR (OC)
_REAR (OC)
OC side
image loss
amount
setting
image loss
amount
setting
0 - 100
20
(2mm)
C
TRAIL_EDGE
(OC)
(OC)
OC rear
edge
image loss
amount
setting
edge
image loss
amount
setting
0 - 100
20
(2mm)
D
Image
loss
amount
setting
SPF
SIDE1
loss
amount
setting
SPF
SIDE1
LEAD_EDGE
(SPF_SIDE1)
(SPF_SIDE1)
Front
surface
lead edge
image loss
amount
setting
surface
lead edge
image loss
amount
setting
0 - 100
20
(2mm)
E
FRONT
_REAR
(SPF_SIDE1)
_REAR
(SPF_SIDE1)
Front
surface
side image
loss
amount
setting
surface
side image
loss
amount
setting
0 - 100
20
(2mm)
F
TRAIL_EDGE
(SPF_SIDE1)
(SPF_SIDE1)
Front
surface
rear edge
image loss
amount
setting
surface
rear edge
image loss
amount
setting
0 - 100
30
(3mm)
G
Image
loss
amount
setting
SPF
SIDE2
loss
amount
setting
SPF
SIDE2
LEAD_EDGE
(SPF_SIDE2)
(SPF_SIDE2)
Back
surface
lead edge
image loss
amount
setting
surface
lead edge
image loss
amount
setting
0 - 100
20
(2mm)
H
FRONT
_REAR
(SPF_SIDE2)
_REAR
(SPF_SIDE2)
Back
surface
side image
loss
amount
setting
surface
side image
loss
amount
setting
0 - 100
20
(2mm)
I
TRAIL_EDGE
(SPF_SIDE2)
(SPF_SIDE2)
Back
surface
rear edge
image loss
amount
setting
surface
rear edge
image loss
amount
setting
0 - 100
30
(3mm)
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 9
A-I: When the adjustment value is increased, the image loss is
increased.
1step = 0.1mm
• 4.3 Inch LCD model
increased.
1step = 0.1mm
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
66
66-1
Purpose
Setting
Function (Purpose) Used to display the FAX-related soft SW (2
- 99) on the LCD to allow changing the soft
SW while checking with the LCD.
SW while checking with the LCD.
Section
FAX
Operation/Procedure
1)
1)
Enter the [SW NO] with 10-key.
* When [C] key is pressed, the entered value of [SW NO] is
* When [C] key is pressed, the entered value of [SW NO] is
cleared.
2)
Press [DATA] button.
The soft SW data entered in procedure 1) is displayed.
* When [SW NO] button is pressed, the display returns to the
The soft SW data entered in procedure 1) is displayed.
* When [SW NO] button is pressed, the display returns to the
initial screen.
3)
Enter the number corresponding to the bit to be changed with
10-key.
[1]
10-key.
[1]
[0]
[0]
[1]
* When [SW NO] button is pressed, the display returns to the
initial screen.
4)
When [EXECUTE] button is pressed, it is highlighted and the
setting is saved.
After saving the setting, [EXECUTE] button returns to the nor-
mal display.
setting is saved.
After saving the setting, [EXECUTE] button returns to the nor-
mal display.
* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns
* When [SYSTEM SETTINGS] key is pressed, the display returns
to the sub number entry screen.
• 4.3 Inch LCD model
When
image
send
mode
(Except
for FAX
and
copy)
image
send
mode
(Except
for FAX
and
copy)
A
Image
loss
amount
setting
OC
loss
amount
setting
OC
LEAD_EDGE
(OC)
(OC)
OC lead
edge
image loss
amount
setting
edge
image loss
amount
setting
0 - 100
0
(0mm)
B
FRONT
_REAR(OC)
_REAR(OC)
OC side
image loss
amount
setting
image loss
amount
setting
0 - 100
0
(0mm)
C
TRAIL_EDGE
(OC)
(OC)
OC rear
edge
image loss
amount
setting
edge
image loss
amount
setting
0 - 100
0
(0mm)
D
Image
loss
amount
setting
SPF
SIDE1
loss
amount
setting
SPF
SIDE1
LEAD_EDGE
(SPF_SIDE1)
(SPF_SIDE1)
Front
surface
lead edge
image loss
amount
setting
surface
lead edge
image loss
amount
setting
0 - 100
0
(0mm)
E
FRONT
_REAR
(SPF_SIDE1)
_REAR
(SPF_SIDE1)
Front
surface
side image
loss
amount
setting
surface
side image
loss
amount
setting
0 - 100
0
(0mm)
F
TRAIL_EDGE
(SPF_SIDE1)
(SPF_SIDE1)
Front
surface
rear edge
image loss
amount
setting
surface
rear edge
image loss
amount
setting
0 - 100
0
(0mm)
When
image
send
mode
(Except
for FAX
and
copy)
image
send
mode
(Except
for FAX
and
copy)
G
Image
loss
amount
setting
SPF
SIDE2
loss
amount
setting
SPF
SIDE2
LEAD_EDGE
(SPF_SIDE2)
(SPF_SIDE2)
Back
surface
lead edge
image loss
amount
setting
surface
lead edge
image loss
amount
setting
0 - 100
0
(0mm)
H
FRONT
_REAR
(SPF_SIDE2)
_REAR
(SPF_SIDE2)
Back
surface
side image
loss
amount
setting
surface
side image
loss
amount
setting
0 - 100
0
(0mm)
I
TRAIL_EDGE
(SPF_SIDE2)
(SPF_SIDE2)
Back
surface
rear edge
image loss
amount
setting
surface
rear edge
image loss
amount
setting
0 - 100
0
(0mm)
Item/Display
Content
Setting
range
Default
value
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$˖
˷̚˹
6&$11(5)$;6(1'$//('*($'-8670(179$/8(
˖/($'B('*(2&
$˖
˖)5217B5($52&
%˖
˖75$,/B('*(2&
&˖
˖/($'B('*(63)B6,'(
'˖
7(67
)$;
6&$11(5
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
)$;62)76:6(77,1*
7(67
6:12
'$7$
6:1R
(;(&87(
MXFXX3 SIMULATIONS, FAX SOFTWARE SWITCH 3 – 10
• 7.0/8.5 Inch LCD model
66-2
Purpose
Setting
Function (Purpose) Used to enter a country code and set the
default value for the country code.
Section
FAX
Operation/Procedure
1)
1)
When the machine enters Simulation 66-02, the following
screen is displayed.
* When [DEST CODE] button is pressed, the display is shifted
screen is displayed.
* When [DEST CODE] button is pressed, the display is shifted
to the country code list screen.
* The country code shift screen is shown on the next page.
* The currently set country code is displayed in the column of
* The currently set country code is displayed in the column of
"PRESENT:".
2)
Enter the country code (8 digits) with 10-key([0]/[1]). The
entered country code is displayed in the column of "NEW:" and
[SET] key becomes active.
* When [C] key is pressed, the column of “NEW:” is cleared.
entered country code is displayed in the column of "NEW:" and
[SET] key becomes active.
* When [C] key is pressed, the column of “NEW:” is cleared.
3)
When [SET] button is pressed after entering the country code,
[EXECUTE] button becomes active. The country code is dis-
played in the column of "PRESENT:", and the column of
"NEW:" is cleared.
* When [C] key is pressed, the display returns to the initial set-
[EXECUTE] button becomes active. The country code is dis-
played in the column of "PRESENT:", and the column of
"NEW:" is cleared.
* When [C] key is pressed, the display returns to the initial set-
ting screen.
4)
When [EXECUTE] button is pressed, it is highlighted and
[YES] and [NO] buttons become active. The country name is
displayed on the tile line.
* When [NO] button is pressed, [EXECUTE] button returns to
[YES] and [NO] buttons become active. The country name is
displayed on the tile line.
* When [NO] button is pressed, [EXECUTE] button returns to
the normal display and [YES] and [NO] buttons become
inactive.
inactive.
5)
When [YES] button is pressed, it is highlighted and the soft SW
corresponding to the country code is initialized.
* During clearing the FAX-related soft SW, [EXECUTE] and
corresponding to the country code is initialized.
* During clearing the FAX-related soft SW, [EXECUTE] and
[YES] buttons are highlighted.
6)
After completion of initialization of the soft SW, [EXECUTE],
[YES], and [NO] buttons become inactive.
* When [CA] key is pressed after completion of initialization of
[YES], and [NO] buttons become inactive.
* When [CA] key is pressed after completion of initialization of
the soft SW, the whole machine is reset.
Operation/Procedure (Shifting to the country page)
* When [DEST CODE] button is pressed on the initial screen, the
* When [DEST CODE] button is pressed on the initial screen, the
display is shifted to the country code list screen.
Use [
Use [
] [] buttons to select the country select page.
When the table item is the top (last) item, [
] [] buttons gray out.
When [
] [] buttons gray out, they are disabled.
* Press [BACK] button to return to the entry screen.
<Country code list>
Initial screen
• 4.3 Inch LCD model
• 4.3 Inch LCD model
• 7.0/8.5 Inch LCD model
JAPAN
00000000
U.S.A.
10110101
AUSTRALIA
00001001
U.K.
10110100
FRANCE
00111101
ǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)$;62)76:6(77,1*
(;(&87(
6:1R
'$7$
䋺
䋺
6:1R
GERMANY
00000100
SWEDEN
10100101
NEWZEALAND
01111110
CHINA
00100110
SINGAPORE
10011100
TW
11111110
MIDDLEANDNEAREAST
11111101
SLOVAKIA
11111100
OTHER3
11111011
FINLAND
00111100
NORWAY
10000010
DENMARK
00110001
NETHERLANDS
01111011
ITALY
01011001
SWITZERLAND
10100110
AUSTRIA
00001010
INDONESIA
01010100
THAILAND
10101001
MALAYSIA
01101100
INDIA
01010011
PHILIPPINES
10001001
HONGKONG
01010000
RUSSIA
10111000
SOUTHAFRICA
10011111
SPAIN
10100000
PORTUGUESE
10001011
LUXEMBURG
01101001
BELGIUM
00001111
CZECH
00101110
HUNGARY
01010001
GREECE
01000110
POLAND
10001010
BRAZIL
00010110
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
)$;62)76:&/($5-$3$1
7(67
6(7
35(6(17
1(:
(;(&87(
685("
<(6
12
'(67&2'(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
)$;62)76:&/($5-$3$1
35(6(17˖
ǂǂ1(:˖
ǂǂ1(:˖
6(7
'(67&2'(
$5(<28685("
<(6
12
(;(&87(
Click on the first or last page to see other MX-FXX3 service manuals if exist.