DOWNLOAD Sharp MX-FXX3 Service Manual ↓ Size: 3.5 MB | Pages: 76 in PDF or view online for FREE

MXFXX3  SIMULATIONS, FAX SOFTWARE SWITCH  3 – 27

• 4.3 Inch LCD model

• 7.0/8.5 Inch LCD model

 

66-61

Setting

Function (Purpose) Used to display the FAX-related soft SW

(100 - 170) on the LCD to allow changing
the soft SW while checking with the LCD.

FAX

Operation/Procedure
1)

Enter the [SW NO] with 10-key.
* When [C] key is pressed, the entered value of [SW NO] is

cleared.

2)

Press [DATA] button.
The soft SW data entered in procedure 1) is displayed.
* When [SW NO] button is pressed, the display returns to the

initial screen.

3)

Enter the number corresponding to the bit to be changed with
10-key.
[1] 

 [0]

[0] 

 [1]

* When [SW NO] button is pressed, the display returns to the

initial screen.

4)

When [EXECUTE] button is pressed, it is highlighted and the
setting is saved.
After saving the setting, [EXECUTE] button returns to the nor-
mal display.

* When [CA] key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display returns

to the sub number entry screen.

• 4.3 Inch LCD model

• 7.0/8.5 Inch LCD model

1

Thru Num.20

Through number 20

0840

Max. 4

Though Number20

Thru Num.21

Through number 21

090

Max. 4

Though Number21

Thru Num.22

Through number 22

0990

Max. 4

Though Number22

Res. Thru Num.1

Reserve Through number 1

Null

Max. 4

Reserve Though Number

Res. Thru Num.2

Reserve Through number 2

Null

Max. 4

Reserve Though Number2

Res. Thru Num.3

Reserve Through number 3

Null

Max. 4

Reserve Though Number3

2

Res. Thru Num.4

Reserve Through number 4

Null

Max. 4

Reserve Though Number4

Res. Thru Num.5

Reserve Through number 5

Null

Max. 4

Reserve Though Number5

Res. Thru Num.6

Reserve Through number 6

Null

Max. 4

Reserve Though Number6

Res. Thru Num.7

Reserve Through number 7

Null

Max. 4

Reserve Though Number7

Res. Thru Num.8

Reserve Through number 8

Null

Max. 4

Reserve Though Number8

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

$&56(77,1*/RFDO&DUULHU1XPEHU

7(67

/RFDO&DU1XP

6(7

/RQJ&DU1XP

2YHU&DU1XP

%\SDVV1XP

8VHU$UHD&G

0DFKLQH&RGH

9HUVLRQ

7KUX1XP

35(6(17

1(:

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$&56(77,1*/RFDO&DUULHU1XPEHU

(;(&87(

35(6(17˖
ǂǂ1(:˖

6(7

/RFDO&DUULHU1XP

/RQJ&DUULHU1XP

%\SDVV1XP

2YHU&DUULHU1XP

8VHU$UHD&RGH

0DFKLQH&RGH

7KUX1XP

9HUVLRQ

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

7KUX1XP

5HV7KUX1XP

5HV7KUX1XP

5HV7KUX1XP

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

)$;62)76:6(77,1*

7(67

6:12

      

       

'$7$

6:1R

(;(&87(

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

)$;62)76:6(77,1*

(;(&87(

6:1R

'$7$

䋺

䋺

6:1R

MXFXX3  SIMULATIONS, FAX SOFTWARE SWITCH  3 – 28

1

1-8

Country code

Control is performed according to the set country code.
The destination setting that is set in SIM66-2 as the image 
send function is reflected.
The country code setting cannot be directly made from this 
SW.

1

North America
* For codes of the other 

countries, refer to the 
page of SIM 66-2 
setting.

0
1
1
0
1
0
1

2

1-4

Calling

Make time (10PPS) 
setting

Setting of make time when dialling at 10PPS.
Make time can be set from 29 to 44ms in 1ms increments by 
binary inputting N over the range of 0 to 15 (N + 29ms).

1

"1011": 40ms 
(Other country)
"0100": 33ms (Malaysia/
Taiwan/South Africa/
Brazil)
"0110": 35ms 
(New Zealand/India/
Hong Kong)
"1000": 37ms (Australia)
"1001": 38ms 
(China/Singapore/
Thailand)

Adjustment 
value

0

1

1

5-8

Calling

Break time setting 
(10PPS) 

Setting of break time when dialling at 10PPS. 
Break time can be set from 56 to 71ms by in 1ms increments 
binary inputting N over the range of 0 to 15 (N + 56ms).

0

"0100": 60ms 
(Other country)
"0110": 62ms 
(China/Singapore/
Thailand/Hong Kong)
"0111": 63ms (Australia)
"1001": 65ms 
(New Zealand/India/
Hong Kong)
"1011": 67ms
 (Malaysia/Taiwan/
South Africa/Brazil)

Adjustment 
value

1

0

0

3

1-4

Calling

Minimum pause time 
(10PPS) setting

Setting of minimum pause time when dialling at 10PPS.
Minimum pause time can be set from 800 to 950ms in 10ms 
increments by binary inputting N over the range of 0 to 15 (N 
x 10ms + 800ms).

0

"0000": 800ms 
(Other country)
"0001": 810ms (France)

Adjustment 
value

0
0
0

5-8

Calling

Minimum pause time 
(20PPS) setting

Setting of minimum pause time when dialling at 20PPS.
Minimum pause time can be set from 450 to 600ms in 10ms 
increments by binary inputting N over the range of 0 to 15 (N 
x 10ms + 450ms).
Functions only in China and Thailand.

0

450ms

Adjustment 
value

0
0
0

4

1-4

Calling

Make time (20PPS) 
setting

Setting of make time when dialing at 20PPS.
Make time can be set from 9 to 24ms by binary inputting N 
over the range of 0 to 15 (N + 9ms).
Functions only in China and Thailand.

1

"1000": (Other country)
"1010": 19ms (China/
Thailand/Hong Kong)

Adjustment 
value

0
0
0

5-8

Calling

Break time setting 
(20PPS)

Setting of break time when dialing at 20PPS.
Break time can be set from 26 to 41ms by binary inputting N 
over the range of 0 to 15 (N + 26ms).
Functions only in China and Thailand.

0

"0111": (Other country)
"0101": 31ms (China/
Thailand/Hong Kong)

Adjustment 
value

1
1
1

5

1-4

Calling

Setting of DTMF send 
level (high group)

This sets the send level of high area and low area DTMF 
signals in units of 1dB.
Setting can be made over the range of 0dB to 15dB in 1dB 
increments by binary inputting.

0

"0101": 5dB (North 
America/Singapore)
"0011": 3dB 
(Other3/Russia)
"0110": 6dB 
(Other country)
"0111": 7dB (Australia/
Malaysia/Philippine/
Hong Kong/Middle East)
"1000": 8dB (Indonesia/
South Africa/Brazil)
"1001": 9dB (India)

Adjustment 
value

1

0

1

5-8

Not used

0
0
0
0

MXFXX3  SIMULATIONS, FAX SOFTWARE SWITCH  3 – 29

6

1-4

Calling

Setting of DTMF send 
level (low group)
High group - Low 
group: level difference

This sets the difference between the DTMF signal high area 
level and low area level in units of 0.5dB.
Setting can be made over the range of -2.0dB to 5.5dB in 
0.5dB increments by binary inputting. 
High group - Low group
"0 0 0 0": -2.0dB

"1 0 0 0": 2.0dB

"0 0 0 1": -1.5dB

"1 0 0 1": 2.5dB

"0 0 1 0": -1.0dB

"1 0 1 0": 3.0dB

"0 0 1 1": -0.5dB

"1 0 1 1": 3.5dB

"0 1 0 0": 0.0dB

"1 1 0 0": 4.0dB

"0 1 0 1": 0.5dB

"1 1 0 1": 4.5dB

"0 1 1 0": 1.0dB

"1 1 1 0": 5.0dB

"0 1 1 1": 1.5dB

"1 1 1 1": 5.5dB

1

"1000": 2.0dB 
(Other country)
"0100": 0.0dB 
(New Zealand)
"1010": 3.0dB (Australia)

Adjustment 
value

0

0

0

5-8

Not used

0
0
0
0

7

1-8

Calling

Setting of DTMF 
minimum pause time

This sets the minimum pause time between DTMF signals 
when sending DTMF signals.
Minimum pause time can be set by binary inputting N over the 
range of 0 to 255 (1ms x N).
Setting can be made over the range of 50ms to 255ms in 1ms 
increments by binary inputting.
When SW15-3,4 are set to other than "MODEM fixed," the set 
value less than 54ms is considered as 54ms.
The initial value is reverted to if a value outside of the setting 
range is set.

0

120ms

Adjustment 
value

1
1
1
1
0
0
0

8

1-5

Calling

DTMF signal send time

This sets the time that DTMF signals are sent when sending 
DTMF signals.
Send time can be set over the rage of 70 to 310ms in 10ms 
increments by binary inputting N from 0 to 31 (110ms x N).
The initial value is reverted to if a value outside of the setting 
range is set.

0

110ms

Adjustment 
value

1
0
1
1

6, 7

Calling

Dial call waiting time

This sets the waiting time from the end of line connection to 
the start of dial call at times of automatic dial calling.
"00": 3.5 seconds
"01": 4 seconds
"10": 5 seconds
"11": 6 seconds
This only functions when dial tone detection is OFF.

0

"00": 3.5 seconds 
(Other country)
"01": 4 seconds (U.K./
Finland/Norway/Denmark/
Netherlands/Italy/New 
Zealand/Slovakia/South 
Africa/Spain/Portuguese/
Luxemburg/Belgium/
Czech/Hungary/Greece/
Poland)

Adjustment 
value

0

8

Calling

Line current detection 
at times of dial calling

Setting to determine whether or not to call dial following 
detection of line current during line connection at times of 
automatic dial calling.
"1": No
"0": Yes
In cases where the setting is "Yes" but no line current can be 
detected, dial is not called but the busy re-call procedure is 
followed.

1

"1": No (North America/
Taiwan/Middle East/
Other3/Russia)
"0": Yes (Other country)

Setting

9

1

Calling

Manual calibration 
setting when sending

Setting to execute the manual calibration or not when 
sending.
In case of an abnormal current waveform, the auto calibration 
fails and the DTFM signal is deformed. This setting provides 
the countermeasure against that problem.
"0": Execute
"1": Not execute

0

Execute

Setting

2

Call 
arrival

Manual calibration 
setting when a signal
arrives

Setting to execute the manual calibration or not when a signal 
arrives.
In case of an abnormal current waveform, the auto calibration 
fails and the transmission is affected. This setting provides 
the countermeasure against that problem.
"0": Execute
"1": Not execute

0

Execute

Setting

3, 4

Not used

1
1

5

Calling

SDT signal detection

Setting to determine whether or not to detect the SDT signal, 
which is the second dial tone when transmitting to the F-net.
When the SDT signal is not detected, ordinary dialling is 
conducted even after 16X dialling.
"0": Do not detect
"1": Detect

0

Do not detect

Setting

6

Calling

No. 2 dial tone 
detection

Setting of ON/OFF of No.2 dial tone detection function.
"0": OFF (No. 2 dial tone detection is not performed.)
"1": ON (No. 2 dial tone detection is performed.)

0

Detection is not performed

Setting

MXFXX3  SIMULATIONS, FAX SOFTWARE SWITCH  3 – 30

9

7

Calling

Dial tone detection

When the setting is "Yes," the dial is sent following 
confirmation of detection of the dial tone when the line is 
captured; and when the setting is "No," dial is sent without a 
dial tone because no confirmation of dial tone detection is 
carried out after line capture.
"0": No
"1": Yes

1

"1": Yes (Other country)
"0": No (Australia/New 
Zealand/China/Indonesia/
Thailand/Malaysia/India/
Philippine/Hong Kong/
Taiwan/Middle East/
Other3/Russia)

Setting

8

Calling

Dial tone ON detection 
time (during 
continuous detection)

This sets the waiting time from the end of line connection to 
the start of dial call at times of automatic dial calling.
"0": 1.5 seconds
"1": 1 seconds

0

1.5 seconds

Adjustment 
value

10

1-4

Calling

Lower limit of dial tone 
ON/OFF detection time 
(during intermittent 
detection)

This sets the lower limit time for detection of dial tone ON/
OFF time.
Setting can be made over the range of 40ms to 490ms in 
30ms increments by binary inputting.
(N x 30ms) + 40ms
This is only valid during intermittent DT detection.

0

"0010": 100ms (North 
America/Australia/New 
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle 
East/Other3/Brazil)
"0001": 70ms 
(Other country)

Adjustment 
value

0

1

0

5-8

Calling

Upper limit of dial tone 
ON/OFF detection time 
(during intermittent 
detection)

This sets the upper limit time for detection of dial tone ON/
OFF time.
 Setting can be made over the range of 400ms to 1900ms in 
100ms increments by binary inputting.
(N x 100ms) + 400ms
This is only valid during intermittent DT detection.

0

"0011": 700ms (North 
America/Australia/New 
Zealand/China/Singapore/
Indonesia/Thailand/
Malaysia/India/Philippine/
Hong Kong/Taiwan/Middle 
East/Other3/Brazil)
"1000": 1200ms 
(Other country)

Adjustment 
value

0

1

1

11

1-4

Calling

External line 
connection number 
setting 1 <First digit>

When No. 2 dial tone is detected, this area is compared with 
the external in connection number. If they match, the units 
waits for No. 2 dial tone.
Up to two external line connection numbers (max. 4 digits) 
can be registered as options.
The first digit of the external line connection number 1 is set.
The numbers and codes which can be registered are as 
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) / 
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].

0

0

Setting

0

0

0

5-8

Calling

External line 
connection number 
setting 1 <Second 
digit>

The second digit of the external line connection number 1 is 
set.
The numbers and codes which can be registered are as 
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) / 
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].

0

0

Setting

0

0

0

12

1-4

Calling

External line 
connection number 
setting 1 <Third digit>

The third digit of the external line connection number 1 is set.
The numbers and codes which can be registered are as 
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) / 
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].

0

0

Setting

0
0

0

5-8

Calling

External line 
connection number 
setting 1 <Fourth digit>

The fourth digit of the external line connection number 1 is 
set.
The numbers and codes which can be registered are as 
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) / 
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].

0

0

Setting

0
0

0

13

1-4

Calling

External line 
connection number 
setting 2 <First digit>

The first digit of the external line connection number 2 is set.
The numbers and codes which can be registered are as 
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) / 
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].

0

0

Setting

0
0

0

5-8

Calling

External line 
connection number 
setting 2 <Second 
digit>

The second digit of the external line connection number 2 is 
set.
The numbers and codes which can be registered are as 
follows.
0 - 9 / * (a) / # (b) / – (pause) (c) / 
Not used for this digit and after (d) / Any is OK (f)
When set to [e], it is considered as setting to [0].

0

0

Setting

0
0

0